Internet Engineering Task Force (IETF) T. Li, Ed.
Request for Comments: 9667 Juniper Networks
Category: Experimental P. Psenak, Ed.
ISSN: 2070-1721 Cisco Systems, Inc.
H. Chen
Futurewei
L. Jalil
Verizon
S. Dontula
AT&T
October 2024
Dynamic Flooding on Dense Graphs
Abstract
Routing with link-state protocols in dense network topologies can
result in suboptimal convergence times due to the overhead associated
with flooding. This can be addressed by decreasing the flooding
topology so that it is less dense.
This document discusses the problem in some depth and an
architectural solution. Specific protocol changes for IS-IS, OSPFv2,
and OSPFv3 are described in this document.
Status of This Memo
This document is not an Internet Standards Track specification; it is
published for examination, experimental implementation, and
evaluation.
This document defines an Experimental Protocol for the Internet
community. This document is a product of the Internet Engineering
Task Force (IETF). It represents the consensus of the IETF
community. It has received public review and has been approved for
publication by the Internet Engineering Steering Group (IESG). Not
all documents approved by the IESG are candidates for any level of
Internet Standard; see Section 2 of RFC 7841.
Information about the current status of this document, any errata,
and how to provide feedback on it may be obtained at
https://www.rfc-editor.org/info/rfc9667.
Copyright Notice
Copyright (c) 2024 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(https://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Revised BSD License text as described in Section 4.e of the
Trust Legal Provisions and are provided without warranty as described
in the Revised BSD License.
Table of Contents
1. Introduction
1.1. Requirements Language
2. Problem Statement
3. Solution Requirements
4. Dynamic Flooding
4.1. Applicability
4.2. Leader Election
4.3. Computing the Flooding Topology
4.4. Topologies on Complete Bipartite Graphs
4.4.1. A Minimal Flooding Topology
4.4.2. Xia Topologies
4.4.3. Optimization
4.5. Encoding the Flooding Topology
4.6. Advertising the Local Edges Enabled for Flooding
5. Protocol Elements
5.1. IS-IS TLVs
5.1.1. IS-IS Area Leader Sub-TLV
5.1.2. IS-IS Dynamic Flooding Sub-TLV
5.1.3. IS-IS Area Node IDs TLV
5.1.4. IS-IS Flooding Path TLV
5.1.5. IS-IS Flooding Request TLV
5.1.6. IS-IS LEEF Advertisement
5.2. OSPF LSAs and TLVs
5.2.1. OSPF Area Leader Sub-TLV
5.2.2. OSPF Dynamic Flooding Sub-TLV
5.2.3. OSPFv2 Dynamic Flooding Opaque LSA
5.2.4. OSPFv3 Dynamic Flooding LSA
5.2.5. OSPF Area Router ID TLVs
5.2.5.1. OSPFv2 Area Router ID TLV
5.2.5.2. OSPFv3 Area Router ID TLV
5.2.6. OSPF Flooding Path TLV
5.2.7. OSPF Flooding Request Bit
5.2.8. OSPF LEEF Advertisement
6. Behavioral Specification
6.1. Terminology
6.2. Flooding Topology
6.3. Leader Election
6.4. Area Leader Responsibilities
6.5. Distributed Flooding Topology Calculation
6.6. Use of LANs in the Flooding Topology
6.6.1. Use of LANs in Centralized Mode
6.6.2. Use of LANs in Distributed Mode
6.6.2.1. Partial Flooding on a LAN in IS-IS
6.6.2.2. Partial Flooding on a LAN in OSPF
6.7. Flooding Behavior
6.8. Treatment of Topology Events
6.8.1. Temporary Addition of Links to the Flooding Topology
6.8.2. Local Link Addition
6.8.3. Node Addition
6.8.4. Failures of Links Not on the Flooding Topology
6.8.5. Failures of Links On the Flooding Topology
6.8.6. Node Deletion
6.8.7. Local Link Addition to the Flooding Topology
6.8.8. Local Link Deletion from the Flooding Topology
6.8.9. Treatment of Disconnected Adjacent Nodes
6.8.10. Failure of the Area Leader
6.8.11. Recovery from Multiple Failures
6.8.12. Rate-Limiting Temporary Flooding
7. IANA Considerations
7.1. IS-IS
7.2. OSPF
7.2.1. OSPF Dynamic Flooding LSA TLVs Registry
7.2.2. OSPF Link Attributes Sub-TLV Bit Values Registry
7.3. IGP
8. Security Considerations
9. References
9.1. Normative References
9.2. Informative References
Acknowledgements
Authors' Addresses
1. Introduction
In recent years, there has been increased focus on how to address the
dynamic routing of networks that have a bipartite (also known as
spine-leaf or leaf-spine), Clos [Clos], or Fat-tree [Leiserson]
topology. Conventional Interior Gateway Protocols (IGPs; i.e., IS-IS
[ISO10589], OSPFv2 [RFC2328], and OSPFv3 [RFC5340]) underperform,
redundantly flooding information throughout the dense topology. This
leads to overloaded control plane inputs and thereby create
operational issues. For practical considerations, network architects
have resorted to applying unconventional techniques to address the
problem, e.g., applying BGP in the data center [RFC7938]. However,
some network architects feel that using an Exterior Gateway Protocol
(EGP) as an IGP is suboptimal, perhaps only because of the
configuration overhead.
The primary issue that is demonstrated when conventional IGPs are
applied is the poor reaction of the network to topology changes.
Normal link-state routing protocols rely on a flooding algorithm for
state distribution within an area. In a dense topology, this
flooding algorithm is highly redundant and results in unnecessary
overhead. Each node in the topology receives each link state update
multiple times. Ultimately, all of the redundant copies will be
discarded, but only after they have reached the control plane and
have been processed. This creates issues because significant Link
State Database (LSDB) updates can become queued behind many redundant
copies of another update. This delays convergence as the LSDB does
not stabilize promptly.
In a real-world implementation, the packet queues leading to the
control plane are necessarily of finite size, so if the flooding rate
exceeds the update processing rate for long enough, then the control
plane will be obligated to drop incoming updates. If these lost
updates are of significance, this will further delay the
stabilization of the LSDB and the convergence of the network.
This is not a new problem. Historically, when routing protocols have
been deployed in networks where the underlying topology is a complete
graph, there have been similar issues. This was more common when the
underlying link-layer fabric presented the network layer with a full
mesh of virtual connections. This was addressed by reducing the
flooding topology through IS-IS Mesh Groups [RFC2973], but this
approach requires careful configuration of the flooding topology.
Thus, the root problem is not limited to massively scalable data
centers. It exists with any dense topology at scale.
Link-state routing protocols were conceived when links were very
expensive and topologies were sparse. The fact that those same
designs are suboptimal in a dense topology should not come as a huge
surprise. Technology has progressed to the point where links are
cheap and common. This represents a complete reversal in the
economic fundamentals of network engineering. The original designs
are to be commended for continuing to provide correct operation to
this point and optimizations for operation in today's environment are
to be expected.
1.1. Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in
BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all
capitals, as shown here.
These words may also appear in this document in lower case as plain
English words without their normative meanings.
2. Problem Statement
In a dense topology, the flooding algorithm that is the heart of
conventional link-state routing protocols causes a great deal of
redundant messaging. This is exacerbated by scale. While the
protocol can survive this combination, the redundant messaging is
unnecessary overhead and delays convergence. Thus, the problem is
how to provide routing in dense, scalable topologies with rapid
convergence.
3. Solution Requirements
A solution to this problem must meet the following requirements:
Requirement 1: Provide a dynamic routing solution. Reachability
must be restored after any topology change.
Requirement 2: Provide a significant improvement in convergence.
Requirement 3: The solution should address a variety of dense
topologies. Just addressing a complete bipartite
topology such as K5,8 is insufficient (see [Bondy]).
Multi-stage Clos topologies must also be addressed,
as well as topologies that are slight variants.
Addressing complete graphs is a good demonstration of
generality.
Requirement 4: There must be no single point of failure. The loss
of any link or node should not unduly hinder
convergence.
Requirement 5: The workload for flooding should be evenly
distributed. A hot spot, where one node has an
extreme workload, would be a performance limitation
and a vulnerability for resiliency.
Requirement 6: Dense topologies are subgraphs of much larger
topologies. Operational efficiency requires that the
dense subgraph not operate in a radically different
manner than the remainder of the topology. While
some operational differences are permissible, they
should be minimized. Any change to any node outside
of the dense subgraph is not acceptable. These
situations occur when massively scaled data centers
are part of an overall larger wide-area network.
Having a second protocol operating just on this
subgraph would add much more complexity at the edge
of the subgraph where the two protocols would have to
interoperate.
4. Dynamic Flooding
The combination of a dense topology and flooding on the physical
topology is suboptimal for network scaling. However, if the flooding
topology is decoupled from the physical topology and restricted to a
greatly reduced portion of that topology, the result can be efficient
flooding and the resilience of existing protocols. A node that
supports flooding on the decoupled flooding topology is said to
support dynamic flooding.
With dynamic flooding, the flooding topology is computed within an
IGP area with the dense topology either centrally on an elected node,
termed the Area Leader, or in a distributed manner on all nodes that
are supporting dynamic flooding. If the flooding topology is
computed centrally, it is encoded into and distributed as part of the
normal LSDB. This is the centralized mode of operation. If the
flooding topology is computed in a distributed fashion, this is the
distributed mode of operation. Nodes within such an IGP area would
only flood on the flooding topology. On links outside of the
flooding topology, normal database synchronization mechanisms, i.e.,
OSPF database exchange and IS-IS Complete Sequence Number PDUs
(CSNPs), would apply, but flooding may not. The detailed behavior of
the nodes participating in IGP is described in Section 6. New link-
state information that arrives from outside of the flooding topology
suggests that the sender has no flooding topology information or that
it is operating on old information about the flooding topology. In
these cases, the new link-state information should be flooded on the
flooding topology as well.
The flooding topology covers the full set of nodes within the area,
but excludes some of the links that standard flooding would employ.
Since the flooding topology is computed before topology changes, the
effort required to compute it does not factor into the convergence
time and can be done when the topology is stable. In the case of
centralized mode, the speed of the computation and its distribution
is not a significant issue.
Graph theory defines the "degree" of a node to be the number of edges
that are attached to the node. To keep the flooding workload
scalable and distributed, there should be no nodes in the flooding
topology that have a much higher degree than other nodes.
If a node does not have any flooding topology information when it
receives new link-state information, it should flood according to
standard flooding rules. This situation will occur when the dense
topology is first established but is unlikely to recur.
Link-state protocols are intentionally designed to be asynchronous
with nodes acting independently. During the flooding process,
different nodes will have different information, resulting in
transient conditions that can temporarily produce suboptimal
forwarding. These periods of transient conditions are known as
"transients."
When centralized mode is used and if there are multiple flooding
topologies being advertised during a transient, then nodes should
flood link-state updates on all of the flooding topologies. Each
node should locally evaluate the election of the Area Leader for the
IGP area and first flood on its flooding topology. The rationale
behind this is straightforward: if there is a transient and there has
been a recent change in Area Leader, then propagating topology
information promptly along the most likely flooding topology should
be the priority.
During transients, loops may form in the flooding topology. This is
not problematic, as the standard flooding rules would cause duplicate
updates to be ignored. Similarly, during transients, the flooding
topology may become disconnected. Section 6.8.11 discusses how such
conditions are handled.
4.1. Applicability
In a complete graph, this approach is appealing because it
drastically decreases the flooding topology without the manual
configuration of mesh groups. By controlling the diameter of the
flooding topology, as well as the maximum node degree in the flooding
topology, convergence time goals can be met, and the stability of the
control plane can be assured.
Similarly, in a massively scaled data center (where there are many
opportunities for redundant flooding), this mechanism guarantees that
flooding is redundant, with each leaf and spine well connected, while
ensuring that no update takes too many hops and that no node shares
an undue portion of the flooding effort.
In a network where only a portion of the nodes support dynamic
flooding, the remaining nodes will continue to perform standard
flooding. This is not an issue for correctness, as no node can
become isolated.
Flooding that is initiated by nodes that support dynamic flooding
will remain within the flooding topology until it reaches a legacy
node, where standard flooding is resumed. Standard flooding will be
bounded by nodes supporting dynamic flooding, which can help limit
the propagation of unnecessary flooding. Whether or not the network
can remain stable in this condition is very dependent on the number
and location of the nodes that support dynamic flooding.
During incremental deployment of dynamic flooding, an area will
consist of one or more sets of connected nodes that support dynamic
flooding and one or more sets of connected nodes that do not, i.e.,
nodes that support standard flooding. The flooding topology is the
union of these sets of nodes. Each set of nodes that does not
support dynamic flooding needs to be part of the flooding topology
and such a set of nodes may provide connectivity between two or more
sets of nodes that support dynamic flooding.
4.2. Leader Election
A single node within the dense topology is elected as an Area Leader.
A generalization of the mechanisms used in existing Designated Router
(OSPF) or Designated Intermediate-System (IS-IS) elections is used
for leader election. The elected node is known as the Area Leader.
In the case of centralized mode, the Area Leader is responsible for
computing and distributing the flooding topology. When a new Area
Leader is elected and has distributed new flooding topology
information, then any prior Area Leaders should withdraw any of their
flooding topology information from their LSDB entries.
In the case of distributed mode, the distributed algorithm advertised
by the Area Leader MUST be used by all nodes that participate in
dynamic flooding.
Not every node needs to be a candidate to be the Area Leader within
an area, as a single candidate is sufficient for correct operation.
However, for redundancy, it is strongly RECOMMENDED that there be
multiple candidates.
4.3. Computing the Flooding Topology
There is a great deal of flexibility in how the flooding topology may
be computed. For resilience, it needs to at least contain a cycle of
all nodes in the dense subgraph. However, additional links could be
added to decrease the convergence time. The trade-off between the
density of the flooding topology and the convergence time is a matter
for further study. The exact algorithm for computing the flooding
topology in the case of the centralized computation need not be
standardized, as it is not an interoperability issue. Only the
encoding of the resultant topology needs to be documented. In the
case of distributed mode, all nodes in the IGP area need to use the
same algorithm to compute the flooding topology. It is possible to
use private algorithms to compute flooding topology, so long as all
nodes in the IGP area use the same algorithm.
While the flooding topology should be a covering cycle, it need not
be a Hamiltonian cycle where each node appears only once. In fact,
in many relevant topologies, this will not be possible (e.g., K5,8).
This is fortunate, as computing a Hamiltonian cycle is known to be
NP-complete.
A simple algorithm to compute the topology for a complete bipartite
graph is to simply select unvisited nodes on each side of the graph
until both sides are completely visited. If the numbers of nodes on
each side of the graph are unequal, then revisiting nodes on the less
populated side of the graph will be inevitable. This algorithm can
run in O(N) time, so it is quite efficient.
While a simple cycle is adequate for correctness and resiliency, it
may not be optimal for convergence. At scale, a cycle may have a
diameter that is half the number of nodes in the graph. This could
cause an undue delay in link-state update propagation. Therefore, it
may be useful to have a bound on the diameter of the flooding
topology. Introducing more links into the flooding topology would
reduce the diameter but at the trade-off of possibly adding redundant
messaging. The optimal trade-off between convergence time and graph
diameter is for further study.
Similarly, if additional redundancy is added to the flooding
topology, specific nodes in that topology may end up with a very high
degree. This could result in overloading the control plane of those
nodes, resulting in poor convergence. Thus, it may be preferable to
have an upper bound on the degree of nodes in the flooding topology.
Again, the optimal trade-off between graph diameter, node degree,
convergence time, and topology computation time is for further study.
If the leader chooses to include a multi-access broadcast LAN segment
as part of the flooding topology, all of the adjacencies in that LAN
segment should be included as well. Once updates are flooded on the
LAN, they will be received by every attached node.
4.4. Topologies on Complete Bipartite Graphs
Complete bipartite graph topologies have become popular for data
center applications and are commonly called leaf-spine or spine-leaf
topologies. This section discusses some flooding topologies that are
of particular interest in these networks.
4.4.1. A Minimal Flooding Topology
A minimal flooding topology on a complete bipartite graph is one in
which the topology is connected and each node has at least degree
two. This is of interest because it guarantees that the flooding
topology has no single point of failure.
In practice, this implies that every leaf node in the flooding
topology will have a degree of two. As there are usually more leaves
than spines, the degree of the spines will be higher, but the load on
the individual spines can be evenly distributed.
This type of flooding topology is also of interest because it scales
well. As the number of leaves increases, it is possible to construct
flooding topologies that perform well. Specifically, for N spines
and M leaves, if M >= N(N/2-1), then there is a flooding topology
that has a diameter of 4.
4.4.2. Xia Topologies
A Xia topology on a complete bipartite graph is one in which all
spine nodes are biconnected through leaves with degree two, but the
remaining leaves all have degree one and are evenly distributed
across the spines.
Constructively, one can create a Xia topology by iterating through
the spines. Each spine can be connected to the next spine by
selecting any unused leaf. Since leaves are connected to all spines,
all leaves will have a connection to both the first and second spine
and one can therefore choose any leaf without loss of generality.
Continuing this iteration across all of the spines, selecting a new
leaf at each iteration will result in a path that connects all
spines. Adding one more leaf between the last and first spine will
produce a cycle of N spines and N leaves.
At this point, M-N leaves remain unconnected. These can be
distributed evenly across the remaining spines and connected by a
single link.
Xia topologies represent a compromise that trades off increased risk
and decreased performance for lower flooding amplification. Xia
topologies will have a larger diameter. For M spines, the diameter
will be M + 2.
In a Xia topology, some leaves are singly connected. This represents
a risk in that convergence may be delayed in some failures. However,
there may be some alternate behaviors that can be employed to
mitigate these risks. If a leaf node sees that its single link on
the flooding topology has failed, it can compensate by performing a
database synchronization check with a different spine. Similarly, if
a leaf determines that its connected spine on the flooding topology
has failed, it can compensate by performing a database
synchronization check with a different spine. In both of these
cases, the synchronization check is intended to ameliorate any delays
in link-state propagation due to the fragmentation of the flooding
topology.
The benefit of this topology is that flooding load is easily
understood. Each node in the spine cycle will never receive an
update more than twice. For M leaves and N spines, a spine never
transmits more than (M/N +1) updates.
4.4.3. Optimization
If two nodes are adjacent in the flooding topology and there is a set
of parallel links between them, then any given update MUST be flooded
over only one of those links. The selection of the specific link is
implementation-specific.
4.5. Encoding the Flooding Topology
There are a variety of ways that the flooding topology could be
encoded efficiently. If the topology was only a cycle, a simple list
of the nodes in the topology would suffice. However, this is
insufficiently flexible, as it would require a slightly different
encoding scheme as soon as a single additional link is added.
Instead, this document chooses to encode the flooding topology as a
set of intersecting paths, where each path is a set of connected
links.
Advertisement of the flooding topology includes support for multi-
access broadcast LANs. When a LAN is included in the flooding
topology, all edges between the LAN and nodes connected to the LAN
are assumed to be part of the flooding topology. To reduce the size
of the flooding topology advertisement, explicit advertisement of
these edges is optional. Note that this may result in the
possibility of "hidden nodes" or "stealth nodes", which are part of
the flooding topology but are not explicitly mentioned in the
flooding topology advertisements. These hidden nodes can be found by
examination of the LSDB where connectivity between a LAN and nodes
connected to the LAN is fully specified.
Note that while all nodes MUST be part of the advertised flooding
topology, not all multi-access LANs need to be included. Only those
LANs that are part of the flooding topology need to be included in
the advertised flooding topology.
Other encodings are certainly possible. This document has attempted
to make a useful trade-off between simplicity, generality, and space.
4.6. Advertising the Local Edges Enabled for Flooding
Correct operation of the flooding topology requires that all nodes
that participate in the flooding topology choose local links for
flooding that are part of the calculated flooding topology. Failure
to do so could result in an unexpected partition of the flooding
topology and/or suboptimal flooding reduction. As an aid to
diagnosing problems when dynamic flooding is in use, this document
defines a means of advertising the Local Edges Enabled for Flooding
(LEEF). The protocol-specific encodings are defined in Sections
5.1.6 and 5.2.8.
The following guidelines apply:
* Advertisement of LEEF is optional.
* As the flooding topology is defined in terms of edges (i.e., pairs
of nodes) and not in terms of links, the advertisement SHOULD
indicate that all such links have been enabled in cases where
parallel adjacencies to the same neighbor exist.
* LEEF advertisements MUST NOT include edges enabled for temporary
flooding (Section 6.7).
* LEEF advertisements MUST NOT be used either when calculating a
flooding topology or when determining what links to add
temporarily to the flooding topology when the flooding topology is
temporarily partitioned.
5. Protocol Elements
5.1. IS-IS TLVs
The following TLVs/sub-TLVs are added to IS-IS:
1. A sub-TLV that an IS may include in its Link State PDU (LSP) to
indicate its preference for becoming the Area Leader.
2. A sub-TLV that an IS may include in its LSP to indicate that it
supports dynamic flooding and the algorithms that it supports for
distributed mode, if any.
3. A TLV to advertise the list of system IDs that compose the
flooding topology for the area. A system ID is an identifier for
a node.
4. A TLV to advertise a path that is part of the flooding topology.
5. A TLV that requests flooding from the adjacent node.
5.1.1. IS-IS Area Leader Sub-TLV
The IS-IS Area Leader Sub-TLV allows a system to:
1. Indicate its eligibility and priority for becoming the Area
Leader.
2. Indicate whether centralized or distributed mode is to be used to
compute the flooding topology in the area.
3. Indicate the algorithm identifier for the algorithm that is used
to compute the flooding topology in distributed mode.
Intermediate Systems (nodes) that are not advertising this sub-TLV
are not eligible to become the Area Leader.
The Area Leader is the node with the numerically highest Area Leader
priority in the area. In the event of ties, the node with the
numerically highest system ID is the Area Leader. Due to transients
during database flooding, different nodes may not agree on the Area
Leader. This is not problematic, as subsequent flooding will cause
the entire area to converge.
The IS-IS Area Leader Sub-TLV is advertised as a sub-TLV of the IS-IS
Router Capability TLV (242) [RFC7981] and has the following format:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | Priority | Algorithm |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 1: IS-IS Area Leader Sub-TLV
Type: 27
Length: 2 octets
Priority: 0-255, unsigned integer. Determination of the priority is
outside of the scope of this document.
Algorithm: A numeric identifier in the range 0-255 that identifies
the algorithm used to calculate the flooding topology. The
following values are defined:
0: Centralized computation by the Area Leader.
1-127: Standardized distributed algorithms.
128-254: Private distributed algorithms. Individual values are
to be assigned according to the "Private Use" policy defined in
Section 4.1 of [RFC8126] (see Section 7.3).
255: Reserved
5.1.2. IS-IS Dynamic Flooding Sub-TLV
The IS-IS Dynamic Flooding Sub-TLV allows a system to:
1. Indicate that it supports dynamic flooding. This is indicated by
the advertisement of this sub-TLV.
2. Indicate the set of algorithms that it supports.
In incremental deployments, understanding which nodes support dynamic
flooding can be used to optimize the flooding topology. In
distributed mode, knowing the capabilities of the nodes can allow the
Area Leader to select the optimal algorithm.
The IS-IS Dynamic Flooding Sub-TLV is advertised as a sub-TLV of the
IS-IS Router Capability TLV (242) [RFC7981] and has the following
format:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | Algorithm... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 2: IS-IS Dynamic Flooding Sub-TLV
Type: 28
Length: 1-255 octets; number of Algorithms
Algorithm: Numeric identifiers in the range 0-255 that identify the
algorithm used to calculate the flooding topology as described in
Section 5.1.1.
5.1.3. IS-IS Area Node IDs TLV
The IS-IS Area Node IDs TLV is only used in centralized mode.
The IS-IS Area Node IDs TLV is used by the Area Leader to enumerate
the node IDs (System ID + pseudonode ID) that it has used in
computing the area flooding topology. Conceptually, the Area Leader
creates a list of node IDs for all nodes in the area (including
pseudonodes for all LANs in the topology) and assigns an index to
each node, starting with index 0. Indices are implicitly assigned
sequentially, with the index of the first node being the Starting
Index and each subsequent node's index is the previous node's index +
1.
Because the space in a single TLV is limited, more than one TLV may
be required to encode all of the node IDs in the area. This TLV may
be present in multiple LSPs.
The IS-IS Area Node IDs TLV has the following format:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | Starting Index |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|L| Reserved | Node IDs ...
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Node IDs continued ....
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 3: IS-IS Area Node IDs TLV
Type: 17
Length: 3 + ((System ID Length + 1) * (number of node IDs)) in
octets
Starting Index: The index of the first node ID that appears in this
TLV.
L (Last): This bit is set if the index of the last node ID that
appears in this TLV is equal to the last index in the full list of
node IDs for the area.
Node IDs: A concatenated list of node IDs for the area.
If multiple IS-IS Area Node IDs TLVs with the L bit set are
advertised by the same node, the TLV that specifies the smaller
maximum index is used and the other TLVs with the L bit set are
ignored. TLVs that specify node IDs with indices greater than that
specified by the TLV with the L bit set are also ignored.
5.1.4. IS-IS Flooding Path TLV
The IS-IS Flooding Path TLV is only used in centralized mode.
The IS-IS Flooding Path TLV is used to denote a path in the flooding
topology. The goal is an efficient encoding of the links of the
topology. A single link is a simple case of a path that only covers
two nodes. A connected path may be described as a sequence of
indices (I1, I2, I3, ...), denoting a link from the system with index
1 to the system with index 2, a link from the system with index 2 to
the system with index 3, and so on.
If a path exceeds the size that can be stored in a single TLV, then
the path may be distributed across multiple TLVs by the replication
of a single system index.
Complex topologies that are not a single path can be described using
multiple TLVs.
The IS-IS Flooding Path TLV contains a list of system indices
relative to the systems advertised through the IS-IS Area Node IDs
TLV. At least 2 indices must be included in the TLV. Due to the
length restriction of TLVs, this TLV can contain 126 system indices
at most.
The IS-IS Flooding Path TLV has the following format:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | Starting Index |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Index 2 | Additional indices ...
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 4: IS-IS Flooding Path TLV
Type: 18
Length: 2 * (number of indices in the path) in octets
Starting Index: The index of the first system in the path.
Index 2: The index of the next system in the path.
Additional indices (optional): A sequence of additional indices to
systems along the path.
5.1.5. IS-IS Flooding Request TLV
The IS-IS Flooding Request TLV allows a system to request an adjacent
node to enable flooding towards it on a specific link in the case
where the connection to the adjacent node is not part of the existing
flooding topology.
A node that supports dynamic flooding MAY include the IS-IS Flooding
Request TLV in its IS-IS Hello (IIH) Protocol Data Units (PDUs).
The IS-IS Flooding Request TLV has the following format:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | Levels | Scope |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 5: IS-IS Flooding Request TLV
Type: 19
Length: 1 + number of advertised flooding scopes in octets
Levels: The levels for which flooding is requested. Levels are
encoded as the circuit type as specified in IS-IS [ISO10589]
Scope (8 bits): Flooding scope for which the flooding is requested
as defined in the LSP Flooding Scope Identifier Registry as
created by [RFC7356]. Inclusion of flooding scopes is optional
and is only necessary if [RFC7356] is supported. Multiple
flooding scopes MAY be included. Values are restricted to the
range 0..127.
Circuit flooding scope MUST NOT be sent in the Flooding Request TLV
and MUST be ignored if received.
When the TLV is received in a level-specific LAN-Hello PDU (L1-LAN-
IIH or L2-LAN-IIH), only levels that match the PDU type are valid.
Levels that do not match the PDU type MUST be ignored on receipt.
When the TLV is received in a Point-to-Point Hello (P2P-IIH), only
levels that are supported by the established adjacency are valid.
Levels that are not supported by the adjacency MUST be ignored on
receipt.
If flooding was disabled on the received link due to dynamic
flooding, then flooding MUST be temporarily enabled over the link for
the specified Circuit Types and flooding scopes received in the in
the IS-IS Flooding Request TLV. Flooding MUST be enabled until the
Circuit Type or Flooding Scope is no longer advertised in the IS-IS
Flooding Request TLV or the TLV no longer appears in IIH PDUs
received on the link.
When flooding is temporarily enabled on the link for any Circuit Type
or Flooding Scope due to receiving the IS-IS Flooding Request TLV,
the receiver MUST perform standard database synchronization for the
corresponding Circuit Types and flooding scopes on the link. In the
case of IS-IS, this results in setting the Send Routeing Message
(SRM) flag for all related LSPs on the link and sending CSNPs.
So long as the IS-IS Flooding Request TLV is being received, flooding
MUST NOT be disabled for any of the Circuit Types or flooding scopes
present in the IS-IS Flooding Request TLV, even if the connection
between the neighbors is removed from the flooding topology.
Flooding for such Circuit Types or flooding scopes MUST continue on
the link and be considered temporarily enabled.
5.1.6. IS-IS LEEF Advertisement
In support of advertising which edges are currently enabled in the
flooding topology, an implementation MAY indicate that a link is part
of the flooding topology by advertising a bit value in the Link
Attributes sub-TLV defined by [RFC5029].
The following bit-value is defined by this document:
Local Edge Enabled for Flooding (LEEF): 0x4
5.2. OSPF LSAs and TLVs
This section defines new Link State Advertisements (LSAs) and TLVs
for both OSPFv2 and OSPFv3.
The following LSAs and TLVs/sub-TLVs are added to OSPFv2/OSPFv3:
1. A TLV that is used to advertise the preference for becoming the
Area Leader.
2. A TLV that is used to indicate the support for dynamic flooding
and the algorithms that the advertising node supports for
distributed mode, if any.
3. An OSPFv2 Opaque LSA and OSPFv3 LSA to advertise the flooding
topology for centralized mode.
4. A TLV to advertise the list of Router IDs that comprise the
flooding topology for the area.
5. A TLV to advertise a path that is part of the flooding topology.
6. A bit in the Link-Local Signaling (LLS) Type 1 Extended Options
and Flags that requests flooding from the adjacent node.
5.2.1. OSPF Area Leader Sub-TLV
The usage of the OSPF Area Leader Sub-TLV is identical to that of the
IS-IS Area Leader Sub-TLV described in Section 5.1.1.
The OSPF Area Leader Sub-TLV is used by both OSPFv2 and OSPFv3.
The OSPF Area Leader Sub-TLV is advertised as a top-level TLV of the
Router Information (RI) LSA that is defined in [RFC7770] and has the
following format:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Priority | Algorithm | Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 6: OSPF Area Leader Sub-TLV
Type: 17
Length: 4 octets
Priority: 0-255, unsigned integer
Algorithm: As defined in Section 5.1.1.
5.2.2. OSPF Dynamic Flooding Sub-TLV
The usage of the OSPF Dynamic Flooding Sub-TLV is identical to that
of the IS-IS Dynamic Flooding Sub-TLV described in Section 5.1.2.
The OSPF Dynamic Flooding Sub-TLV is used by both OSPFv2 and OSPFv3.
The OSPF Dynamic Flooding Sub-TLV is advertised as a top-level TLV of
the RI LSA that is defined in [RFC7770] and has the following format:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Algorithm ... | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 7: OSPF Dynamic Flooding Sub-TLV
Type: 18
Length: Number of Algorithms in octets
Algorithm: As defined in Section 5.1.1.
5.2.3. OSPFv2 Dynamic Flooding Opaque LSA
The OSPFv2 Dynamic Flooding Opaque LSA is only used in centralized
mode.
The OSPFv2 Dynamic Flooding Opaque LSA is used to advertise
additional data related to dynamic flooding in OSPFv2. OSPFv2 Opaque
LSAs are described in [RFC5250].
Multiple OSPFv2 Dynamic Flooding Opaque LSAs can be advertised by an
OSPFv2 router. The flooding scope of the OSPFv2 Dynamic Flooding
Opaque LSA is area-local.
The format of the OSPFv2 Dynamic Flooding Opaque LSA is as follows:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| LS age | Options | LS Type |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 10 | Opaque ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Advertising Router |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| LS sequence number |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| LS checksum | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+- TLVs -+
| ... |
Figure 8: OSPFv2 Dynamic Flooding Opaque LSA
The opaque type used by OSPFv2 Dynamic Flooding Opaque LSA is 10.
The opaque type is used to differentiate the various types of OSPFv2
Opaque LSAs as described in Section 3 of [RFC5250]. The LS Type is
10. The LSA Length field [RFC2328] represents the total length (in
octets) of the Opaque LSA including the LSA header and all TLVs
(including padding).
The Opaque ID field is an arbitrary value used to maintain multiple
Dynamic Flooding Opaque LSAs. For OSPFv2 Dynamic Flooding Opaque
LSAs, the Opaque ID has no semantic significance other than to
differentiate Dynamic Flooding Opaque LSAs originated from the same
OSPFv2 router.
The format of the TLVs within the body of the OSPFv2 Dynamic Flooding
Opaque LSA is the same as the format used by the Traffic Engineering
Extensions to OSPF [RFC3630].
The Length field defines the length of the value portion in octets
(thus a TLV with no value portion would have a length of 0 octets).
The TLV is padded to a 4-octet alignment; padding is not included in
the length field (so a 3-octet value would have a length of 3 octets,
but the total size of the TLV would be 8 octets). Nested TLVs are
also 32-bit aligned. For example, a 1-octet value would have the
length field set to 1, and 3 octets of padding would be added to the
end of the value portion of the TLV. The padding is composed of
zeros.
5.2.4. OSPFv3 Dynamic Flooding LSA
The OSPFv3 Dynamic Flooding Opaque LSA is only used in centralized
mode.
The OSPFv3 Dynamic Flooding LSA is used to advertise additional data
related to dynamic flooding in OSPFv3.
The OSPFv3 Dynamic Flooding LSA has a function code of 16. The
flooding scope of the OSPFv3 Dynamic Flooding LSA is area-local. The
U bit will be set indicating that the OSPFv3 Dynamic Flooding LSA
should be flooded even if it is not understood. The Link State ID
(LSID) value for this LSA is the Instance ID. OSPFv3 routers MAY
advertise multiple OSPFv3 Dynamic Flooding Opaque LSAs in each area.
The format of the OSPFv3 Dynamic Flooding LSA is as follows:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| LS age |1|0|1| 16 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Link State ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Advertising Router |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| LS sequence number |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| LS checksum | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+- TLVs -+
| ... |
Figure 9: OSPFv3 Dynamic Flooding LSA
5.2.5. OSPF Area Router ID TLVs
In OSPF, TLVs are defined to advertise indices associated with nodes
and Broadcast / Non-Broadcast Multi-Access (NBMA) networks. Due to
identifier differences between OSPFv2 and OSPFv3, two different TLVs
are defined as described in the following sub-sections.
The OSPF Area Router ID TLVs are used by the Area Leader to enumerate
the Router IDs that it has used in computing the flooding topology.
This includes the identifiers associated with Broadcast/NBMA networks
as defined for Network LSAs. Conceptually, the Area Leader creates a
list of Router IDs for all routers in the area and assigns an index
to each router, starting with index 0. Indices are implicitly
assigned sequentially, with the index of the first node being the
Starting Index and each subsequent node's index is the previous
node's index + 1.
5.2.5.1. OSPFv2 Area Router ID TLV
This TLV is a top-level TLV of the OSPFv2 Dynamic Flooding Opaque
LSA.
Because the space in a single OSPFv2 opaque LSA is limited, more than
one LSA may be required to encode all of the Router IDs in the area.
This TLV MAY be advertised in multiple OSPFv2 Dynamic Flooding Opaque
LSAs so that all Router IDs can be advertised.
The OSPFv2 Area Router IDs TLV has the following format:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Starting Index |L| Flags | Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+- OSPFv2 Router ID TLV Entry -+
| ... |
Figure 10: OSPFv2 Area Router IDs TLV
Type: 1
Length: 4 + sum of the lengths of all TLV entries in octets
Starting Index: The index of the first Router/Designated Router ID
that appears in this TLV.
L (Last): This bit is set if the index of the last Router/Designated
Router ID that appears in this TLV is equal to the last index in
the full list of Router IDs for the area.
OSPFv2 Router ID TLV Entries: A concatenated list of Router ID TLV
Entries for the area.
If multiple OSPFv2 Area Router ID TLVs with the L bit set are
advertised by the same router, the TLV that specifies the smaller
maximum index is used and the other TLVs with L bit set are ignored.
TLVs that specify Router IDs with indices greater than that specified
by the TLV with the L bit set are also ignored.
Each entry in the OSPFv2 Area Router IDs TLV represents either a node
or a Broadcast/NBMA network identifier. An entry has the following
format:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ID Type | Number of IDs | Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+- Originating Router ID/DR Address -+
| ... |
Figure 11: OSPFv2 Router IDs TLV Entry
ID Type: 1 octet. The following values are defined:
1: Router
2: Designated Router
Number of IDs: 2 octets
Reserved: 1 octet. MUST be transmitted as 0 and MUST be ignored on
receipt.
Originating Router ID/DR Address: (4 * Number of IDs) octets as
indicated by the ID Type.
5.2.5.2. OSPFv3 Area Router ID TLV
This TLV is a top-level TLV of the OSPFv3 Dynamic Flooding LSA.
Because the space in a single OSPFv3 Dynamic Flooding LSA is limited,
more than one LSA may be required to encode all of the Router IDs in
the area. This TLV MAY be advertised in multiple OSPFv3 Dynamic
Flooding Opaque LSAs so that all Router IDs can be advertised.
The OSPFv3 Area Router IDs TLV has the following format:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Starting Index |L| Flags | Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+- OSPFv3 Router ID TLV Entry -+
| ... |
Figure 12: OSPFv3 Area Router IDs TLV
Type: 1
Length: 4 + sum of the lengths of all TLV entries in octets
Starting Index: The index of the first Router/Designated Router ID
that appears in this TLV.
L (Last): This bit is set if the index of the last Router/Designated
Router ID that appears in this TLV is equal to the last index in
the full list of Router IDs for the area.
OSPFv3 Router ID TLV Entries: A concatenated list of Router ID TLV
Entries for the area.
If multiple OSPFv3 Area Router ID TLVs with the L bit set are
advertised by the same router the TLV that specifies the smaller
maximum index is used and the other TLVs with L bit set are ignored.
TLVs that specify Router IDs with indices greater than that specified
by the TLV with the L bit set are also ignored.
Each entry in the OSPFv3 Area Router IDs TLV represents either a
router or a Broadcast/NBMA network identifier. An entry has the
following format:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ID Type | Number of IDs | Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+- Originating ID Entry -+
| ... |
Figure 13: OSPFv3 Router ID TLV Entry
ID Type: 1 octet. The following values are defined:
1: Router
2: Designated Router
Number of IDs: 2 octets
Reserved: 1 octet. MUST be transmitted as 0 and MUST be ignored on
receipt.
The Originating ID Entry takes one of the following forms, depending
on the ID Type.
For a Router:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Originating Router ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
The length of the Originating ID Entry is (4 * Number of IDs) octets.
For a Designated Router:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Originating Router ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Interface ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
The length of the Originating ID Entry is (8 * Number of IDs) octets.
5.2.6. OSPF Flooding Path TLV
The OSPF Flooding Path TLV is a top-level TLV of the OSPFv2 Dynamic
Flooding Opaque LSAs and OSPFv3 Dynamic Flooding LSA.
The usage of the OSPF Flooding Path TLV is identical to that of the
IS-IS Flooding Path TLV described in Section 5.1.4.
The OSPF Flooding Path TLV contains a list of Router ID indices
relative to the Router IDs advertised through the OSPF Area Router
IDs TLV. At least 2 indices must be included in the TLV.
Multiple OSPF Flooding Path TLVs can be advertised in a single OSPFv2
Dynamic Flooding Opaque LSA or OSPFv3 Dynamic Flooding LSA. OSPF
Flooding Path TLVs can also be advertised in multiple OSPFv2 Dynamic
Flooding Opaque LSAs or OSPFv3 Dynamic Flooding LSAs if they all
cannot fit in a single LSA.
The OSPF Flooding Path TLV has the following format:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Starting Index | Index 2 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+- Additional Indices -+
| ... |
Figure 14: OSPF Flooding Path TLV
Type: 2
Length: 2 * (number of indices in the path) in octets
Starting Index: The index of the first Router ID in the path.
Index 2: The index of the next Router ID in the path.
Additional indices (optional): A sequence of additional indices to
Router IDs along the path.
5.2.7. OSPF Flooding Request Bit
A single new option bit, the Flooding Request (FR) bit, is defined in
the LLS Type 1 Extended Options and Flags field [RFC5613]. The FR
bit allows a router to request an adjacent node to enable flooding
towards it on a specific link in the case where the connection to the
adjacent node is not part of the current flooding topology.
A node that supports dynamic flooding MAY include the FR bit in its
OSPF LLS Extended Options and Flags TLV.
If the FR bit is signaled for a link on which flooding was disabled
due to dynamic flooding, then flooding MUST be temporarily enabled
over the link. Flooding MUST be enabled until the FR bit is no
longer advertised in the OSPF LLS Extended Options and Flags TLV or
the OSPF LLS Extended Options and Flags TLV no longer appears in the
OSPF Hellos.
When flooding is temporarily enabled on the link for any area due to
receiving the FR bit in the OSPF LLS Extended Options and Flags TLV,
the receiver MUST perform standard database synchronization for the
area corresponding to the link. If the adjacency is already in the
FULL state, the mechanism specified in [RFC4811] MUST be used for
database resynchronization.
So long as the FR bit is being received in the OSPF LLS Extended
Options and Flags TLV for a link, flooding MUST NOT be disabled on
the link, even if the connection between the neighbors is removed
from the flooding topology. Flooding MUST continue on the link and
be considered as temporarily enabled.
5.2.8. OSPF LEEF Advertisement
In support of advertising the specific edges that are currently
enabled in the flooding topology, an implementation MAY indicate that
a link is part of the flooding topology. The OSPF Link Attributes
Bits TLV is defined to support this advertisement.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Link Attribute Bits |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+- Additional Link Attribute Bits -+
| ... |
Figure 15: OSPF Link Attributes Bits TLV
Type: 21 (for OSPFv2) or 10 (for OSPFv3)
Length: Size of the Link Attribute Bits in octets. It MUST be a
multiple of 4 octets.
The following bits are defined:
Bit #0: Local Edge Enabled for Flooding (LEEF)
OSPF Link-attribute Bits TLV appears as:
1. A sub-TLV of the OSPFv2 Extended Link TLV [RFC7684].
2. A sub-TLV of the OSPFv3 Router-Link TLV [RFC8362].
6. Behavioral Specification
This section specifies the detailed behavior of the nodes
participating in the IGP.
6.1. Terminology
Some terminology to be used in the following sections:
Reachable: A node is considered reachable if it is part of the
connected network graph. Note that this is independent of any
constraints that may be considered when performing IGP shortest-
path tree calculation, e.g., link metrics, overload bit state,
etc. The two-way connectivity check MUST be performed before
including an edge in the connected network graph.
Connected: A node is connected to the flooding topology if it has at
least one local link, which is part of the flooding topology.
Disconnected: A node is disconnected from the flooding topology when
it is not connected to the flooding topology.
Current flooding topology: The latest version of the flooding
topology that has been received (in the case of centralized mode)
or calculated locally (in the case of distributed mode).
6.2. Flooding Topology
The flooding topology MUST include all reachable nodes in the area.
If a node's reachability changes, the flooding topology MUST be
recalculated. In centralized mode, the Area Leader MUST advertise a
new flooding topology.
If a node becomes disconnected from the current flooding topology but
is still reachable, then a new flooding topology MUST be calculated.
In centralized mode, the Area Leader MUST advertise the new flooding
topology.
The flooding topology SHOULD be biconnected to provide network
resiliency, but this does incur some amount of redundant flooding.
Xia topologies (Section 4.4.2) are an example of an explicit decision
to sacrifice resiliency to avoid redundancy.
6.3. Leader Election
Any capable node MAY advertise its eligibility to become the Area
Leader.
Nodes that are not reachable are not eligible to become the Area
Leader. Nodes that do not advertise their eligibility to become the
Area Leader are not eligible. Amongst the eligible nodes, the node
with the numerically highest priority is the Area Leader. If
multiple nodes all have the highest priority, then the node with the
numerically highest system identifier (in the case of IS-IS) or
Router ID (in the case of OSPFv2 and OSPFv3) is the Area Leader.
6.4. Area Leader Responsibilities
If the Area Leader operates in centralized mode, it MUST advertise
algorithm 0 in its Area Leader Sub-TLV. For dynamic flooding to be
enabled, it also MUST compute and advertise a flooding topology for
the area. The Area Leader may update the flooding topology at any
time. However, it should not destabilize the network with undue or
overly frequent topology changes. If the Area Leader operates in
centralized mode and needs to advertise a new flooding topology, it
floods the new flooding topology on both the new and old flooding
topologies.
If the Area Leader operates in distributed mode, it MUST advertise a
nonzero algorithm in its Area Leader Sub-TLV.
When the Area Leader advertises algorithm 0 in its Area Leader Sub-
TLV and does not advertise a flooding topology, dynamic flooding is
disabled for the area. Note this applies whether the Area Leader
intends to operate in centralized mode or distributed mode.
Note that once dynamic flooding is enabled, disabling it risks
destabilizing the network due to the issues discussed in Section 1.
6.5. Distributed Flooding Topology Calculation
If the Area Leader advertises a nonzero algorithm in its Area Leader
Sub-TLV, all nodes in the area that support dynamic flooding and
support the algorithm advertised by the Area Leader MUST compute the
flooding topology based on the Area Leader's advertised algorithm.
Nodes that do not support the advertised algorithm MUST continue to
use standard IS-IS/OSPF flooding mechanisms. Nodes that do not
support the flooding algorithm advertised by the Area Leader MUST be
considered as dynamic flooding incapable nodes by the Area Leader.
If the value of the algorithm advertised by the Area Leader is from
the range 128-254 (private distributed algorithms), it is the
responsibility of the network operator to guarantee that all nodes in
the area agree on the dynamic flooding algorithm corresponding to the
advertised value.
6.6. Use of LANs in the Flooding Topology
The use of LANs in the flooding topology differs depending on whether
the area is operating in centralized mode or distributed mode.
6.6.1. Use of LANs in Centralized Mode
As specified in Section 4.5, when a LAN is advertised as part of the
flooding topology, all nodes connected to the LAN are assumed to be
using the LAN as part of the flooding topology. This assumption is
made to reduce the size of the flooding topology advertisement.
6.6.2. Use of LANs in Distributed Mode
In distributed mode, the flooding topology is NOT advertised; thus,
the space consumed to advertise it is not a concern. Therefore, it
is possible to assign only a subset of the nodes connected to the LAN
to use the LAN as part of the flooding topology. Doing so may
further optimize flooding by reducing the amount of redundant
flooding on a LAN. However, support of flooding by a subset of the
nodes connected to a LAN requires some modest but backward-compatible
changes in the way flooding is performed on a LAN.
6.6.2.1. Partial Flooding on a LAN in IS-IS
The Designated Intermediate System (DIS) for a LAN MUST use the
standard flooding behavior.
Non-DIS nodes whose connection to the LAN is included in the flooding
topology MUST use the standard flooding behavior.
Non-DIS nodes whose connection to the LAN is NOT included in the
flooding topology behave as follows:
* Received CSNPs from the DIS are ignored.
* Partial Sequence Number PDUs (PSNPs) are NOT originated on the
LAN.
* An LSP that is received on the LAN and is newer than the
corresponding LSP present in the Link State PDU Database (LSPDB)
is retained and flooded on all local circuits that are part of the
flooding topology (i.e., do not discard newer LSPs simply because
they were received on a LAN that the receiving node is not using
for flooding).
* An LSP received on the LAN that is older or the same as the
corresponding LSP in the LSPDB is silently discarded.
* LSPs received on links other than the LAN are NOT flooded on the
LAN.
NOTE: If any node connected to the LAN requests the enablement of
temporary flooding, all nodes MUST revert to the standard flooding
behavior on the LAN.
6.6.2.2. Partial Flooding on a LAN in OSPF
The Designated Router (DR) and Backup Designated Router (BDR) for
LANs MUST use the standard flooding behavior.
Non-DR/BDR nodes with a connection to a LAN that is included in the
flooding topology use the standard flooding behavior on that LAN.
Non-DR/BDR nodes with a connection to a LAN that is NOT included in
the flooding topology behave as follows:
* LSAs received on the LAN are acknowledged to the DR/BDR.
* LSAs received on interfaces other than the LAN are NOT flooded on
the LAN.
NOTE: If any node connected to the LAN requests the enablement of
temporary flooding, all nodes revert to the standard flooding
behavior.
NOTE: The sending of LSA Acknowledgements by nodes NOT using the LAN
as part of the flooding topology eliminates the need for changes on
the part of the DR/BDR, which might include nodes that do not support
the dynamic flooding algorithm.
6.7. Flooding Behavior
Nodes that support dynamic flooding MUST use the flooding topology
for flooding when possible and MUST NOT revert to standard flooding
when a valid flooding topology is available.
In some cases, a node that supports dynamic flooding may need to add
local links to the flooding topology temporarily, even though the
links are not part of the calculated flooding topology. This is
termed "temporary flooding" and is discussed in Section 6.8.1.
In distributed mode, the flooding topology is calculated locally. In
centralized mode, the flooding topology is advertised in the area
LSDB. Received link-state updates, whether received on a link that
is in the flooding topology or on a link that is not in the flooding
topology, MUST be flooded on all links that are in the flooding
topology except for the link on which the update was received.
In centralized mode, new information in the form of new paths or new
node ID assignments can be received at any time. This may replace
some or all of the existing information about the flooding topology.
There may be transient conditions where the information that a node
has is inconsistent or incomplete. If a node detects that its
current information is inconsistent, then the node may wait for an
implementation-specific amount of time, expecting more information to
arrive that will provide a consistent, complete view of the flooding
topology.
In both centralized and distributed mode, if a node determines that
some of its adjacencies are to be added to the flooding topology, it
should add those and begin flooding on those adjacencies immediately.
If a node determines that adjacencies are to be removed from the
flooding topology, then it should wait for an implementation-specific
amount of time before acting on that information. This serves to
ensure that new information is flooded promptly and completely,
allowing all nodes to receive updates in a timely fashion.
6.8. Treatment of Topology Events
This section explicitly considers a variety of different topological
events in the network and how dynamic flooding should address them.
6.8.1. Temporary Addition of Links to the Flooding Topology
When temporary flooding is enabled on the link, the flooding needs to
be enabled in both directions. To achieve that, the following steps
MUST be performed:
* The LSDB needs to be resynchronised on the link. This is done
using the standard protocol mechanisms. In the case of IS-IS,
this results in setting the SRM bit for all LSPs on the circuit
and sending a complete set of CSNPs on the link. In OSPF, the
mechanism specified in [RFC4811] is used.
* Flooding is enabled locally on the link.
* Flooding is requested from the neighbor using the mechanism
specified in Sections 5.1.5 or 5.2.7.
The request for temporary flooding MUST be withdrawn on the link when
all of the following conditions are met:
* The node itself is connected to the current flooding topology.
* The adjacent node is connected to the current flooding topology.
Any change in the flooding topology MUST result in an evaluation of
the above conditions for any link on which temporary flooding was
enabled.
Temporary flooding is stopped on the link when both adjacent nodes
stop requesting temporary flooding on the link.
6.8.2. Local Link Addition
If a local link is added to the topology, the protocol will form a
normal adjacency on the link and update the appropriate LSAs for the
nodes on either end of the link. These link state updates will be
flooded on the flooding topology.
In centralized mode, the Area Leader may choose to retain the
existing flooding topology or modify the flooding topology upon
receiving these updates. If the Area Leader decides to change the
flooding topology, it will update the flooding topology in the LSDB
and flood it using the new flooding topology.
In distributed mode, any change in the topology, including the link
addition, MUST trigger the flooding topology recalculation. This is
done to ensure that all nodes converge to the same flooding topology,
regardless of the time of the calculation.
Temporary flooding MUST be enabled on the newly added local link as
long as at least one of the following conditions are met:
* The node on which the local link was added is not connected to the
current flooding topology.
* The new adjacent node is not connected to the current flooding
topology.
Note that in this case there is no need to perform a database
synchronization as part of the enablement of the temporary flooding
because it was part of the adjacency bring-up itself.
If multiple local links are added to the topology before the flooding
topology is updated, temporary flooding MUST be enabled on a subset
of these links per the conditions discussed in Section 6.8.12.
6.8.3. Node Addition
If a node is added to the topology, then at least one link is also
added to the topology. Section 6.8.2 applies.
A node that has a large number of neighbors is at risk of introducing
a local flooding storm if all neighbors are brought up at once and
temporary flooding is enabled on all links simultaneously. The most
robust way to address this is to limit the rate of initial adjacency
formation following bootup. This reduces unnecessary redundant
flooding as part of initial database synchronization and minimizes
the need for temporary flooding, as it allows time for the new node
to be added to the flooding topology after only a small number of
adjacencies have been formed.
In the event a node elects to bring up a large number of adjacencies
simultaneously, a significant amount of redundant flooding may be
introduced as multiple neighbors of the new node enable temporary
flooding to the new node, which initially is not part of the flooding
topology.
6.8.4. Failures of Links Not on the Flooding Topology
If a link that is not part of the flooding topology fails, then the
adjacent nodes will update their LSAs and flood them on the flooding
topology.
In centralized mode, the Area Leader may choose to retain the
existing flooding topology or modify the flooding topology upon
receiving these updates. If it elects to change the flooding
topology, it will update the flooding topology in the LSDB and flood
it using the new flooding topology.
In distributed mode, any change in the topology, including the
failure of the link that is not part of the flooding topology, MUST
trigger the flooding topology recalculation. This is done to ensure
that all nodes converge to the same flooding topology, regardless of
the time of the calculation.
6.8.5. Failures of Links On the Flooding Topology
If there is a failure on the flooding topology, the adjacent nodes
will update their LSAs and flood them. If the original flooding
topology is biconnected, the flooding topology should still be
connected despite a single failure.
If the failed local link represented the only connection to the
flooding topology on the node where the link failed, the node MUST
enable temporary flooding on a subset of its local links. This
allows the node to send its updated LSAs and receive link-state
updates from other nodes in the network before the new flooding
topology is calculated and distributed (in the case of centralized
mode).
In centralized mode, the Area Leader will notice the change in the
flooding topology, recompute the flooding topology, and flood it
using the new flooding topology.
In distributed mode, all nodes supporting dynamic flooding will
notice the change in the topology and recompute the new flooding
topology.
6.8.6. Node Deletion
If a node is deleted from the topology, then at least one link is
also removed from the topology. Section 6.8.4 and Section 6.8.5
apply.
6.8.7. Local Link Addition to the Flooding Topology
If the flooding topology changes and a local link that was not part
of the flooding topology is now part of the flooding topology, then
the node MUST:
* Resynchronize the LSDB over the link. This is done using the
standard protocol mechanisms. In the case of IS-IS, this requires
sending a complete set of CSNPs. In OSPF, the mechanism specified
in [RFC4811] is used.
* Make the link part of the flooding topology and start flooding on
it.
6.8.8. Local Link Deletion from the Flooding Topology
If the flooding topology changes and a local link that was part of
the flooding topology is no longer part of the flooding topology,
then the node MUST remove the link from the flooding topology.
The node MUST keep flooding on such link for a limited amount of time
to allow other nodes to migrate to the new flooding topology.
If the removed local link represented the only connection to the
flooding topology on the node, the node MUST enable temporary
flooding on a subset of its local links. This allows the node to
send its updated LSAs and receive link-state updates from other nodes
in the network before the new flooding topology is calculated and
distributed (in the case of centralized mode).
6.8.9. Treatment of Disconnected Adjacent Nodes
Every time there is a change in the flooding topology, a node MUST
check if any adjacent nodes are disconnected from the current
flooding topology. Temporary flooding MUST be enabled towards a
subset of the disconnected nodes per Sections 6.8.12 and 6.7.
6.8.10. Failure of the Area Leader
The failure of the Area Leader can be detected by observing that it
is no longer reachable. In this case, the Area Leader election
process is repeated and a new Area Leader is elected.
To minimize disruption to dynamic flooding if the Area Leader becomes
unreachable, the node that has the second-highest priority for
becoming Area Leader (including the system identifier / Router ID
tiebreaker if necessary) SHOULD advertise the same algorithm in its
Area Leader Sub-TLV as the Area Leader and (in centralized mode)
SHOULD advertise a flooding topology. This SHOULD be done even when
the Area Leader is reachable.
In centralized mode, the new Area Leader will compute a new flooding
topology and flood it using the new flooding topology. To minimize
disruption, the new flooding topology SHOULD have as much in common
as possible with the old flooding topology. This will minimize the
risk of excess flooding with the new flooding topology.
In the distributed mode, the new flooding topology will be calculated
on all nodes that support the algorithm that is advertised by the new
Area Leader. Nodes that do not support the algorithm advertised by
the new Area Leader will no longer participate in dynamic flooding
and will revert to standard flooding.
6.8.11. Recovery from Multiple Failures
In the event of multiple failures on the flooding topology, it may
become partitioned. The nodes that remain active on the edges of the
flooding topology partitions will recognize this and will try to
repair the flooding topology locally by enabling temporary flooding
towards the nodes that they consider disconnected from the flooding
topology until a new flooding topology becomes connected again.
Nodes, where local failure was detected, update their LSAs and flood
them on the remainder of the flooding topology.
In centralized mode, the Area Leader will notice the change in the
flooding topology, recompute the flooding topology, and flood it
using the new flooding topology.
In distributed mode, all nodes that actively participate in dynamic
flooding will compute the new flooding topology.
Note that this is very different from the area partition because
there is still a connected network graph between the nodes in the
area. The area may remain connected and forwarding may still be
functioning correctly.
6.8.12. Rate-Limiting Temporary Flooding
As discussed in the previous sections, some events require the
introduction of temporary flooding on edges that are not part of the
current flooding topology. This can occur regardless of whether the
area is operating in centralized mode or distributed mode.
Nodes that decide to enable temporary flooding also have to decide
whether to do so on a subset of the edges that are currently not part
of the flooding topology or on all the edges that are currently not
part of the flooding topology. Doing the former risks a longer
convergence time as it may miss vital edges and not fully repair the
flooding topology. Doing the latter risks introducing a flooding
storm that destabilizes the network.
It is recommended that a node rate limit the number of edges on which
it chooses to enable temporary flooding. Initial values for the
number of edges on which to enable temporary flooding and the rate at
which additional edges may subsequently be enabled is left as an
implementation decision.
7. IANA Considerations
7.1. IS-IS
The following code points have been assigned in the "IS-IS Sub-TLVs
for IS-IS Router CAPABILITY TLV" registry (IS-IS TLV 242).
+======+========================+==========================+
| Type | Description | Reference |
+======+========================+==========================+
| 27 | IS-IS Area Leader | RFC 9667 (Section 5.1.1) |
+------+------------------------+--------------------------+
| 28 | IS-IS Dynamic Flooding | RFC 9667 (Section 5.1.2) |
+------+------------------------+--------------------------+
Table 1
IANA has assigned code points from the "IS-IS Top-Level TLV
Codepoints" registry, one for each of the following TLVs:
+======+========================+==========================+
| Type | Description | Reference |
+======+========================+==========================+
| 17 | IS-IS Area Node IDs | RFC 9667 (Section 5.1.3) |
+------+------------------------+--------------------------+
| 18 | IS-IS Flooding Path | RFC 9667 (Section 5.1.4) |
+------+------------------------+--------------------------+
| 19 | IS-IS Flooding Request | RFC 9667 (Section 5.1.5) |
+------+------------------------+--------------------------+
Table 2
IANA has extended the "IS-IS Neighbor Link-Attribute Bit Values"
registry to contain an "L2BM" column that indicates if a bit may
appear in an L2 Bundle Member Attributes TLV. All existing rows have
the value "N" for "L2BM". The following explanatory note has been
added to the registry:
| The "L2BM" column indicates applicability to the L2 Bundle Member
| Attributes TLV. The options for the "L2BM" column are:
|
| Y - This bit MAY appear in the L2 Bundle Member Attributes TLV.
|
| N - This bit MUST NOT appear in the L2 Bundle Member Attributes
| TLV.
IANA has allocated a new bit-value from the "IS-IS Neighbor Link-
Attribute Bit Values" registry.
+=======+======+========================================+===========+
| Value | L2BM | Name | Reference |
+=======+======+========================================+===========+
| 0x4 | N | Local Edge Enabled | RFC 9667 |
| | | for Flooding (LEEF) | |
+-------+------+----------------------------------------+-----------+
Table 3
7.2. OSPF
The following code points have been assigned in the "OSPF Router
Information (RI) TLVs" registry:
+=======+=======================+==========================+
| Value | TLV Name | Reference |
+=======+=======================+==========================+
| 17 | OSPF Area Leader | RFC 9667 (Section 5.2.1) |
+-------+-----------------------+--------------------------+
| 18 | OSPF Dynamic Flooding | RFC 9667 (Section 5.2.2) |
+-------+-----------------------+--------------------------+
Table 4
The following code points have been assigned in the "Opaque Link-
State Advertisements (LSA) Option Types" registry:
+=======+====================================+=================+
| Value | Opaque Type | Reference |
+=======+====================================+=================+
| 10 | OSPFv2 Dynamic Flooding Opaque LSA | RFC 9667 |
| | | (Section 5.2.3) |
+-------+------------------------------------+-----------------+
Table 5
The following code point has been assigned in the "OSPFv3 LSA
Function Codes" registry:
+=======+=============================+==========================+
| Value | LSA Function Code Name | Reference |
+=======+=============================+==========================+
| 16 | OSPFv3 Dynamic Flooding LSA | RFC 9667 (Section 5.2.4) |
+-------+-----------------------------+--------------------------+
Table 6
IANA has assigned a new bit in the "LLS Type 1 Extended Options and
Flags" registry:
+==============+======================+==========================+
| Bit Position | Description | Reference |
+==============+======================+==========================+
| 0x00000020 | Flooding Request bit | RFC 9667 (Section 5.2.7) |
+--------------+----------------------+--------------------------+
Table 7
The following code point has been assigned in the "OSPFv2 Extended
Link TLV Sub-TLVs" registry:
+======+========================+===========+===================+
| Type | Description | Reference | L2 Bundle Member |
| | | | Attributes (L2BM) |
+======+========================+===========+===================+
| 21 | OSPFv2 Link Attributes | RFC 9667 | Y |
| | Bits Sub-TLV | (Section | |
| | | 5.2.8) | |
+------+------------------------+-----------+-------------------+
Table 8
The following code point has been assigned in the "OSPFv3 Extended
LSA Sub-TLVs" registry:
+======+========================+===========+===================+
| Type | Description | Reference | L2 Bundle Member |
| | | | Attributes (L2BM) |
+======+========================+===========+===================+
| 10 | OSPFv3 Link Attributes | RFC 9667 | Y |
| | Bits Sub-TLV | (Section | |
| | | 5.2.8) | |
+------+------------------------+-----------+-------------------+
Table 9
7.2.1. OSPF Dynamic Flooding LSA TLVs Registry
A new registry has been created: "OSPF Dynamic Flooding LSA TLVs".
New values can be allocated via IETF Review or IESG Approval.
The "OSPF Dynamic Flooding LSA TLVs" registry defines top-level TLVs
for the OSPFv2 Dynamic Flooding Opaque LSA and OSPFv3 Dynamic
Flooding LSAs. It has been added to the "Open Shortest Path First
(OSPF) Parameters" registry group.
The following initial values have been allocated:
+======+======================+==========================+
| Type | Description | Reference |
+======+======================+==========================+
| 0 | Reserved | RFC 9667 |
+------+----------------------+--------------------------+
| 1 | OSPF Area Router IDs | RFC 9667 (Section 5.2.5) |
+------+----------------------+--------------------------+
| 2 | OSPF Flooding Path | RFC 9667 (Section 5.2.6) |
+------+----------------------+--------------------------+
Table 10
Types in the range 32768-33023 are Reserved for Experimental Use;
these will not be registered with IANA and MUST NOT be mentioned by
RFCs.
Types in the range 33024-65535 are Reserved. They are not to be
assigned at this time. Before any assignments can be made in the
33024-65535 range, there MUST be an IETF specification that specifies
IANA Considerations that cover the range being assigned.
7.2.2. OSPF Link Attributes Sub-TLV Bit Values Registry
A new registry has been created: "OSPF Link Attributes Sub-TLV Bit
Values". New values can be allocated via IETF Review or IESG
Approval.
The "OSPF Link Attributes Sub-TLV Bit Values" registry defines Link
Attribute bit-values for the OSPFv2 Link Attributes Sub-TLV and
OSPFv3 Link Attributes Sub-TLV. It has been added to the "Open
Shortest Path First (OSPF) Parameters" registry group. This registry
contains a column "L2BM" that indicates if a bit may appear in an L2
Bundle Member Attributes (L2BM) Sub-TLV. The following explanatory
note has been added to the registry:
| The "L2BM" column indicates applicability to the L2 Bundle Member
| Attributes sub-TLV. The options for the "L2BM" column are:
|
| Y - This bit MAY appear in the L2 Bundle Member Attributes sub-
| TLV.
|
| N - This bit MUST NOT appear in the L2 Bundle Member Attributes
| sub-TLV.
The following initial value is allocated:
+========+=====================+===========+===================+
| Bit | Description | Reference | L2 Bundle Member |
| Number | | | Attributes (L2BM) |
+========+=====================+===========+===================+
| 0 | Local Edge Enabled | RFC 9667 | N |
| | for Flooding (LEEF) | (Section | |
| | | 5.2.8) | |
+--------+---------------------+-----------+-------------------+
Table 11
7.3. IGP
IANA has created a registry called "IGP Algorithm Type For Computing
Flooding Topology" in the existing "Interior Gateway Protocol (IGP)
Parameters" registry group.
The registration policy for this registry is Expert Review.
Values in this registry come from the range 0-255.
The initial values in the "IGP Algorithm Type For Computing Flooding
Topology" registry are as follows:
+=========+==================================================+
| Value | Description |
+=========+==================================================+
| 0 | Reserved for centralized mode |
+---------+--------------------------------------------------+
| 1-127 | Unassigned. Individual values are to be |
| | assigned according to the "Expert Review" policy |
| | defined in [RFC8126]. The designated experts |
| | should require a clear, public specification of |
| | the algorithm and comply with [RFC7370]. |
+---------+--------------------------------------------------+
| 128-254 | Reserved for Private Use |
+---------+--------------------------------------------------+
| 255 | Reserved |
+---------+--------------------------------------------------+
Table 12
8. Security Considerations
This document introduces no new security issues. Security of routing
within a domain is already addressed as part of the routing protocols
themselves. This document proposes no changes to those security
architectures.
An attacker could become the Area Leader and introduce a flawed
flooding algorithm into the network thus compromising the operation
of the protocol. Authentication methods as described in [RFC5304]
and [RFC5310] for IS-IS, [RFC2328] and [RFC7474] for OSPFv2, and
[RFC5340] and [RFC4552] for OSPFv3 SHOULD be used to prevent such
attacks.
9. References
9.1. Normative References
[ISO10589] ISO, "Information technology - Telecommunications and
information exchange between systems - Intermediate System
to Intermediate System intra-domain routeing information
exchange protocol for use in conjunction with the protocol
for providing the connectionless-mode network service (ISO
8473)", Second Edition, ISO/IEC 10589:2002, November 2002,
<https://www.iso.org/standard/30932.html>.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<https://www.rfc-editor.org/info/rfc2119>.
[RFC2328] Moy, J., "OSPF Version 2", STD 54, RFC 2328,
DOI 10.17487/RFC2328, April 1998,
<https://www.rfc-editor.org/info/rfc2328>.
[RFC4552] Gupta, M. and N. Melam, "Authentication/Confidentiality
for OSPFv3", RFC 4552, DOI 10.17487/RFC4552, June 2006,
<https://www.rfc-editor.org/info/rfc4552>.
[RFC5029] Vasseur, JP. and S. Previdi, "Definition of an IS-IS Link
Attribute Sub-TLV", RFC 5029, DOI 10.17487/RFC5029,
September 2007, <https://www.rfc-editor.org/info/rfc5029>.
[RFC5250] Berger, L., Bryskin, I., Zinin, A., and R. Coltun, "The
OSPF Opaque LSA Option", RFC 5250, DOI 10.17487/RFC5250,
July 2008, <https://www.rfc-editor.org/info/rfc5250>.
[RFC5304] Li, T. and R. Atkinson, "IS-IS Cryptographic
Authentication", RFC 5304, DOI 10.17487/RFC5304, October
2008, <https://www.rfc-editor.org/info/rfc5304>.
[RFC5310] Bhatia, M., Manral, V., Li, T., Atkinson, R., White, R.,
and M. Fanto, "IS-IS Generic Cryptographic
Authentication", RFC 5310, DOI 10.17487/RFC5310, February
2009, <https://www.rfc-editor.org/info/rfc5310>.
[RFC5340] Coltun, R., Ferguson, D., Moy, J., and A. Lindem, "OSPF
for IPv6", RFC 5340, DOI 10.17487/RFC5340, July 2008,
<https://www.rfc-editor.org/info/rfc5340>.
[RFC5613] Zinin, A., Roy, A., Nguyen, L., Friedman, B., and D.
Yeung, "OSPF Link-Local Signaling", RFC 5613,
DOI 10.17487/RFC5613, August 2009,
<https://www.rfc-editor.org/info/rfc5613>.
[RFC7356] Ginsberg, L., Previdi, S., and Y. Yang, "IS-IS Flooding
Scope Link State PDUs (LSPs)", RFC 7356,
DOI 10.17487/RFC7356, September 2014,
<https://www.rfc-editor.org/info/rfc7356>.
[RFC7474] Bhatia, M., Hartman, S., Zhang, D., and A. Lindem, Ed.,
"Security Extension for OSPFv2 When Using Manual Key
Management", RFC 7474, DOI 10.17487/RFC7474, April 2015,
<https://www.rfc-editor.org/info/rfc7474>.
[RFC7684] Psenak, P., Gredler, H., Shakir, R., Henderickx, W.,
Tantsura, J., and A. Lindem, "OSPFv2 Prefix/Link Attribute
Advertisement", RFC 7684, DOI 10.17487/RFC7684, November
2015, <https://www.rfc-editor.org/info/rfc7684>.
[RFC7770] Lindem, A., Ed., Shen, N., Vasseur, JP., Aggarwal, R., and
S. Shaffer, "Extensions to OSPF for Advertising Optional
Router Capabilities", RFC 7770, DOI 10.17487/RFC7770,
February 2016, <https://www.rfc-editor.org/info/rfc7770>.
[RFC7981] Ginsberg, L., Previdi, S., and M. Chen, "IS-IS Extensions
for Advertising Router Information", RFC 7981,
DOI 10.17487/RFC7981, October 2016,
<https://www.rfc-editor.org/info/rfc7981>.
[RFC8126] Cotton, M., Leiba, B., and T. Narten, "Guidelines for
Writing an IANA Considerations Section in RFCs", BCP 26,
RFC 8126, DOI 10.17487/RFC8126, June 2017,
<https://www.rfc-editor.org/info/rfc8126>.
[RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
May 2017, <https://www.rfc-editor.org/info/rfc8174>.
[RFC8362] Lindem, A., Roy, A., Goethals, D., Reddy Vallem, V., and
F. Baker, "OSPFv3 Link State Advertisement (LSA)
Extensibility", RFC 8362, DOI 10.17487/RFC8362, April
2018, <https://www.rfc-editor.org/info/rfc8362>.
9.2. Informative References
[Bondy] Bondy, J. A. and U. S. R. Murty, "Graph Theory With
Applications", Elsevier Science Publishing Co., Inc.,
ISBN 0-444-19451-7, 1976,
<https://www.zib.de/groetschel/teaching/WS1314/
BondyMurtyGTWA.pdf>.
[Clos] Clos, C., "A study of non-blocking switching networks",
The Bell System Technical Journal, Volume 32, Issue 2, pp.
406-424, DOI 10.1002/j.1538-7305.1953.tb01433.x, March
1953,
<https://doi.org/10.1002/j.1538-7305.1953.tb01433.x>.
[Leiserson]
Leiserson, C. E., "Fat-trees: Universal networks for
hardware-efficient supercomputing", IEEE Transactions on
Computers, Volume C-34, Issue 10, pp. 892-901,
DOI 10.1109/TC.1985.6312192, October 1985,
<https://doi.org/10.1109/TC.1985.6312192>.
[RFC2973] Balay, R., Katz, D., and J. Parker, "IS-IS Mesh Groups",
RFC 2973, DOI 10.17487/RFC2973, October 2000,
<https://www.rfc-editor.org/info/rfc2973>.
[RFC3630] Katz, D., Kompella, K., and D. Yeung, "Traffic Engineering
(TE) Extensions to OSPF Version 2", RFC 3630,
DOI 10.17487/RFC3630, September 2003,
<https://www.rfc-editor.org/info/rfc3630>.
[RFC4811] Nguyen, L., Roy, A., and A. Zinin, "OSPF Out-of-Band Link
State Database (LSDB) Resynchronization", RFC 4811,
DOI 10.17487/RFC4811, March 2007,
<https://www.rfc-editor.org/info/rfc4811>.
[RFC7370] Ginsberg, L., "Updates to the IS-IS TLV Codepoints
Registry", RFC 7370, DOI 10.17487/RFC7370, September 2014,
<https://www.rfc-editor.org/info/rfc7370>.
[RFC7938] Lapukhov, P., Premji, A., and J. Mitchell, Ed., "Use of
BGP for Routing in Large-Scale Data Centers", RFC 7938,
DOI 10.17487/RFC7938, August 2016,
<https://www.rfc-editor.org/info/rfc7938>.
Acknowledgements
The authors would like to thank Sarah Chen, Tony Przygienda, Dave
Cooper, Gyan Mishra, and Les Ginsberg for their contributions to this
work. The authors would also like to thank Arista Networks for
supporting the development of this technology.
The authors would like to thank Zeqing (Fred) Xia, Naiming Shen, Adam
Sweeney, Acee Lindem, and Olufemi Komolafe for their helpful
comments.
The authors would like to thank Tom Edsall for initially introducing
them to the problem.
Advertising Local Edges Enabled for Flooding (LEEF) is based on an
idea proposed by Huaimo Chen, Mehmet Toy, Yi Yang, Aijun Wang, Xufeng
Liu, Yanhe Fan, and Lei Liu. The authors wish to thank them for
their contributions.
Authors' Addresses
Tony Li (editor)
Juniper Networks
1133 Innovation Way
Sunnyvale, California 94089
United States of America
Email: tony.li@tony.li
Peter Psenak (editor)
Cisco Systems, Inc.
Eurovea Centre, Central 3
Pribinova Street 10
81109 Bratislava
Slovakia
Email: ppsenak@cisco.com
Huaimo Chen
Futurewei
Boston, Massachusetts
United States of America
Email: hchen.ietf@gmail.com
Luay Jalil
Verizon
Richardson, Texas 75081
United States of America
Email: luay.jalil@verizon.com