Rfc9600
TitleTRansparent Interconnection of Lots of Links (TRILL): Explicit Congestion Notification (ECN) Support
AuthorD. Eastlake 3rd, B. Briscoe
DateAugust 2024
Format:HTML, TXT, PDF, XML
Status:PROPOSED STANDARD





Internet Engineering Task Force (IETF)                   D. Eastlake 3rd
Request for Comments: 9600                                    B. Briscoe
Category: Standards Track                                    Independent
ISSN: 2070-1721                                              August 2024


     TRansparent Interconnection of Lots of Links (TRILL): Explicit
                 Congestion Notification (ECN) Support

Abstract

   Explicit Congestion Notification (ECN) allows a forwarding element to
   notify downstream devices, including the destination, of the onset of
   congestion without having to drop packets.  This can improve network
   efficiency through better congestion control without packet drops.
   This document extends ECN to TRansparent Interconnection of Lots of
   Links (TRILL) switches, including integration with IP ECN, and
   provides for ECN marking in the TRILL header extension flags word
   (RFC 7179).

Status of This Memo

   This is an Internet Standards Track document.

   This document is a product of the Internet Engineering Task Force
   (IETF).  It represents the consensus of the IETF community.  It has
   received public review and has been approved for publication by the
   Internet Engineering Steering Group (IESG).  Further information on
   Internet Standards is available in Section 2 of RFC 7841.

   Information about the current status of this document, any errata,
   and how to provide feedback on it may be obtained at
   https://www.rfc-editor.org/info/rfc9600.

Copyright Notice

   Copyright (c) 2024 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (https://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Revised BSD License text as described in Section 4.e of the
   Trust Legal Provisions and are provided without warranty as described
   in the Revised BSD License.

Table of Contents

   1.  Introduction
     1.1.  Conventions Used in This Document
   2.  The ECN-Specific Extended Header Flags
   3.  ECN Support
     3.1.  Ingress ECN Support
     3.2.  Transit ECN Support
     3.3.  Egress ECN Support
       3.3.1.  Non-ECN Egress RBridges
       3.3.2.  ECN Egress RBridges
   4.  TRILL Support for ECN Variants
     4.1.  Pre-Congestion Notification (PCN)
     4.2.  Low Latency, Low Loss, and Scalable Throughput (L4S)
   5.  IANA Considerations
   6.  Security Considerations
   7.  References
     7.1.  Normative References
     7.2.  Informative References
   Appendix A.  TRILL Transit RBridge Behavior to Support L4S
   Acknowledgements
   Authors' Addresses

1.  Introduction

   Explicit Congestion Notification (ECN) [RFC3168] [RFC8311] allows a
   forwarding element (such as a router) to notify downstream devices,
   including the destination, of the onset of congestion without having
   to drop packets.  This can improve network efficiency through better
   congestion control without packet drops.  The forwarding element can
   explicitly mark a proportion of packets in an ECN field instead of
   dropping packets.  For example, a 2-bit field is available for ECN
   marking in IP headers.

                     .............................
                     .                           .
                 +---------+                     .
    +------+     | Ingress |                     .
    |Source|  +->| RBridge |                     .   +----------+
    +---+--+  |  |   RB1   |                     .   |Forwarding|
        |     |  +------+--+  +----------+       .   | Element  |
        v     |      .  |     | Transit  |       .   |    Y     |
      +-------+--+   .  +---->| RBridges |       .   +--------+-+
      |Forwarding|   .        |   RBn    |       .      ^     |
      | Element  |   .        +-------+--+  +---------+ |     v
      |    X     |   .                |     | Egress  | |  +-----------+
      +----------+   .                +---->| RBridge +-+  |Destination|
                     .                      |   RB9   |    +-----------+
                     .  TRILL               +---------+
                     .  campus                   .
                     .............................

                  Figure 1: Example Path-Forwarding Nodes

   In [RFC3168], it was recognized that tunnels and lower-layer
   protocols would need to support ECN, and ECN markings would need to
   be propagated, as headers were encapsulated and decapsulated.
   [RFC9599] gives guidelines on the addition of ECN to protocols like
   TRILL that often encapsulate IP packets, including propagation of ECN
   from and to IP.

   In Figure 1, assuming IP traffic, RB1 is an encapsulator and RB9 is a
   decapsulator.  Traffic from Source to RB1 might or might not get
   marked as having experienced congestion in forwarding elements, such
   as X, before being encapsulated at ingress RB1.  Any such ECN marking
   is encapsulated with a TRILL header [RFC6325].

   This document specifies how ECN marking in traffic at the ingress is
   copied into the TRILL extension header flags word and requires such
   copying for IP traffic.  It also enables congestion marking by a
   congested RBridge (such as RBn or RB1 above) in the TRILL header
   extension flags word [RFC7179].

   At RB9, the TRILL egress, it specifies how any ECN markings in the
   TRILL header flags word and in the encapsulated traffic are combined
   so that subsequent forwarding elements, such as Y and the
   Destination, can see if congestion was experienced at any previous
   point in the path from the Source.

   A large part of the guidelines for adding ECN to lower-layer
   protocols [RFC9599] concerns safe propagation of congestion
   notifications in scenarios where some of the nodes do not support or
   understand ECN.  Such ECN ignorance is not a major problem with
   RBridges using this specification, because the method specified
   assures that, if an egress RBridge is ECN ignorant (so it cannot
   further propagate ECN) and congestion has been encountered, the
   egress RBridge will at least drop the packet, and this drop will
   itself indicate congestion to end stations.

1.1.  Conventions Used in This Document

   The terminology and acronyms defined in [RFC6325] are used herein
   with the same meaning.

   In this documents, "IP" refers to both IPv4 and IPv6.

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
   "OPTIONAL" in this document are to be interpreted as described in
   BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all
   capitals, as shown here.

   Abbreviations:

   AQM:  Active Queue Management

   CCE:  Critical Congestion Experienced

   CE:  Congestion Experienced

   CItE:  Critical Ingress-to-Egress

   ECN:  Explicit Congestion Notification

   ECT:  ECN-Capable Transport

   L4S:  Low Latency, Low Loss, and Scalable throughput

   NCHbH:  Non-Critical Hop-by-Hop

   NCCE:  Non-Critical Congestion Experienced

   Not-ECT:  Not ECN-Capable Transport

   PCN:  Pre-Congestion Notification

2.  The ECN-Specific Extended Header Flags

   The extension header fields for ECN in TRILL are defined as a 2-bit
   TRILL-ECN field and a one-bit CCE field in the 32-bit TRILL header
   extension flags word [RFC7780].

   These fields are shown in Figure 2 as "ECN" and "CCE".  The TRILL-ECN
   field consists of bits 12 and 13, which are in the range reserved for
   NCHbH bits.  The CCE field consists of bit 26, which is in the range
   reserved for CItE bits.  The CRItE bit is the critical Ingress-to-
   Egress summary bit and will be one if, and only if, any of the bits
   in the CItE range (21-26) are one or there is a critical feature
   invoked in some further extension of the TRILL header after the
   extension flags word.  The other bits and fields shown in Figure 2
   are not relevant to ECN.  See [RFC7780], [RFC7179], and [IANAthFlags]
   for the meaning of these other bits and fields.

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |Crit.|  CHbH   |   NCHbH   |CRSV | NCRSV |   CItE    |  NCItE  |
   |.....|.........|...........|.....|.......|...........|.........|
   |C|C|C|       |C|N|     |   |     |       |         | |   |     |
   |R|R|R|       |R|C|     |ECN| Ext |       |         |C|Ext|     |
   |H|I|R|       |C|C|     |   | Hop |       |         |C|Clr|     |
   |b|t|s|       |A|A|     |   | Cnt |       |         |E|   |     |
   |H|E|v|       |F|F|     |   |     |       |         | |   |     |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

     Figure 2: The TRILL-ECN and CCE TRILL Header Extension Flags Word
                                   Fields

   Table 1 shows the meaning of the codepoints in the TRILL-ECN field.
   The first three have the same meaning as the corresponding ECN field
   codepoints in the IP header, as defined in [RFC3168].  However,
   codepoint 0b11 is called NCEE to distinguish it from CE in IP.

        +========+=========+=====================================+
        | Binary | Name    | Meaning                             |
        +========+=========+=====================================+
        |   00   | Not-ECT | Not ECN-Capable Transport           |
        +--------+---------+-------------------------------------+
        |   01   | ECT(1)  | ECN-Capable Transport (1)           |
        +--------+---------+-------------------------------------+
        |   10   | ECT(0)  | ECN-Capable Transport (0)           |
        +--------+---------+-------------------------------------+
        |   11   | NCCE    | Non-Critical Congestion Experienced |
        +--------+---------+-------------------------------------+

                   Table 1: TRILL-ECN Field Codepoints

3.  ECN Support

   This section specifies interworking between TRILL and the original
   standardized form of ECN in IP [RFC3168].

   The subsections below describe the required behavior to support ECN
   at TRILL ingress, transit, and egress.  The ingress behavior occurs
   as a native frame is encapsulated with a TRILL header to produce a
   TRILL Data packet.  The transit behavior occurs in all RBridges where
   TRILL Data packets are queued, usually at the output port (including
   the output port of the TRILL ingress).  The egress behavior occurs
   where a TRILL Data packet is decapsulated and output as a native
   frame through an RBridge port.

   An RBridge that supports ECN MUST behave as described in the relevant
   subsections below, which correspond to the recommended provisions in
   Section 3 of this document and Sections 4.2 through 4.4 of [RFC9599].
   Nonetheless, the scheme is designed to safely propagate some form of
   congestion notification even if some RBridges in the path followed by
   a TRILL Data packet support ECN and others do not.

3.1.  Ingress ECN Support

   The behavior at an ingress RBridge is as follows:

   *  When encapsulating an IP frame, the ingress RBridge MUST:

      -  set the F flag in the main TRILL header [RFC7780];

      -  create a flags word as part of the TRILL header;

      -  copy the two ECN bits from the IP header into the TRILL-ECN
         field (flags word bits 12 and 13); and

      -  ensure the CCE flag is set to zero (flags word bit 26).

   *  When encapsulating a frame for a non-IP protocol (where that
      protocol has a means of indicating that ECN is understood by the
      ingress RBridge), the ingress RBridge MUST follow the guidelines
      in Section 4.3 of [RFC9599] to add a flags word to the TRILL
      header.  For a non-IP protocol with an ECN field similar to IP,
      this would be achieved by copying into the TRILL-ECN field from
      the encapsulated native frame.

3.2.  Transit ECN Support

   The transit behavior, shown below, is required at all RBridges where
   TRILL Data packets are queued, usually at the output port.

   *  An RBridge that supports ECN MUST implement some form of AQM
      according to the guidelines of [RFC7567].  The RBridge detects
      congestion either by monitoring its own queue depth or by
      participating in a link-specific protocol.

   *  If the TRILL header flags word is present, whenever the AQM
      algorithm decides to indicate critical congestion on a TRILL Data
      packet, it MUST set the CCE flag (flags word bit 26).  Note that
      Classic ECN marking [RFC3168] only uses critical congestion
      indications, but the two variants in Section 4.1 use a combination
      of critical and non-critical congestion indications.

   *  If the TRILL header flags word is not present, the RBridge will
      either drop the packet or it MAY do all of the following instead
      to indicate congestion:

      -  set the F flag in the main TRILL header;

      -  add a flags word to the TRILL header;

      -  set the TRILL-ECN field to Not-ECT (00); and

      -  set the CCE flag and the critical Ingress-to-Egress summary bit
         (CRItE).

   Note that a transit RBridge that supports ECN does not refer to the
   TRILL-ECN field before signaling CCE in a packet.  It signals CCE
   irrespective of whether the packet indicates that the transport is
   ECN capable.  The egress/decapsulation behavior ensures that a CCE
   indication is converted to a drop if the transport is not ECN
   capable.

3.3.  Egress ECN Support

3.3.1.  Non-ECN Egress RBridges

   If the egress RBridge does not support ECN, that RBridge will ignore
   bits 12 and 13 of any flags word that is present because it does not
   contain any special ECN logic.  Nonetheless, if a transit RBridge has
   set the CCE flag, the egress will drop the packet.  This is because
   drop is the default behavior for an RBridge decapsulating a CItE flag
   when it has no specific logic to understand it.  Drop is the intended
   behavior for such a packet, as required by Section 4.4 of [RFC9599].

3.3.2.  ECN Egress RBridges

   If an RBridge supports ECN, for the two cases of an IP and a non-IP
   inner packet, the egress behavior is as follows:

   Decapsulating an inner IP packet:  The RBridge sets the ECN field of
      the outgoing native IP packet using Table 3.  It MUST set the ECN
      field of the outgoing IP packet to the codepoint at the
      intersection of the row for the arriving encapsulated IP packet
      and the column for 3-bit ECN codepoint in the arriving outer TRILL
      Data packet TRILL header.  If no TRILL header extension flags word
      is present, the 3-bit ECN codepoint is assumed to be all zero
      bits.

      The name of the TRILL 3-bit ECN codepoint used in Table 3 is
      defined using the combination of the TRILL-ECN and CCE fields in
      Table 2.  Specifically, the TRILL 3-bit ECN codepoint is called CE
      if either NCCE or CCE is set in the TRILL header extension flags
      word.  Otherwise, it has the same name as the 2-bit TRILL-ECN
      codepoint.

      In the case where the TRILL 3-bit ECN codepoint indicates CE but
      the encapsulated native IP frame indicates a Not-ECT, it can be
      seen that the RBridge MUST drop the packet.  Such packet dropping
      is necessary because a transport above the IP layer that is not
      ECN capable will have no ECN logic, so it will only understand
      dropped packets as an indication of congestion.

   Decapsulating a non-IP protocol frame:  If the frame has a means of
      indicating ECN that is understood by the RBridge, it MUST follow
      the guidelines in Section 4.4 of [RFC9599] when setting the ECN
      information in the decapsulated native frame.  For a non-IP
      protocol with an ECN field similar to IP, this would be achieved
      by combining the information in the TRILL header flags word with
      the encapsulated non-IP native frame, as specified in Table 3.

    +================+=====+=========================================+
    | TRILL-ECN      | CCE | Arriving TRILL 3-Bit ECN Codepoint Name |
    +=========+======+     |                                         |
    | Name    | Bits |     |                                         |
    +=========+======+=====+=========================================+
    | Not-ECT |  00  |  0  | Not-ECT                                 |
    +---------+------+-----+-----------------------------------------+
    | ECT(1)  |  01  |  0  | ECT(1)                                  |
    +---------+------+-----+-----------------------------------------+
    | ECT(0)  |  10  |  0  | ECT(0)                                  |
    +---------+------+-----+-----------------------------------------+
    | NCCE    |  11  |  0  | CE                                      |
    +---------+------+-----+-----------------------------------------+
    | Not-ECT |  00  |  1  | CE                                      |
    +---------+------+-----+-----------------------------------------+
    | ECT(1)  |  01  |  1  | CE                                      |
    +---------+------+-----+-----------------------------------------+
    | ECT(0)  |  10  |  1  | CE                                      |
    +---------+------+-----+-----------------------------------------+
    | NCCE    |  11  |  1  | CE                                      |
    +---------+------+-----+-----------------------------------------+

        Table 2: Mapping of TRILL-ECN and CCE Fields to the TRILL
                         3-Bit ECN Codepoint Name

   +=====================+============================================+
   | Inner Native Header |  Arriving TRILL 3-Bit ECN Codepoint Name   |
   |                     +=========+============+============+========+
   |                     | Not-ECT |   ECT(0)   |   ECT(1)   |   CE   |
   +=====================+=========+============+============+========+
   |       Not-ECT       | Not-ECT | Not-ECT(*) | Not-ECT(*) | <drop> |
   +---------------------+---------+------------+------------+--------+
   |        ECT(0)       |  ECT(0) |   ECT(0)   |   ECT(1)   |   CE   |
   +---------------------+---------+------------+------------+--------+
   |        ECT(1)       |  ECT(1) | ECT(1)(*)  |   ECT(1)   |   CE   |
   +---------------------+---------+------------+------------+--------+
   |          CE         |    CE   |     CE     |   CE(*)    |   CE   |
   +---------------------+---------+------------+------------+--------+

                       Table 3: Egress ECN Behavior

   An asterisk in Table 3 indicates a combination that is currently
   unused in all variants of ECN marking (see Section 4) and therefore
   SHOULD be logged.

   With one exception, the mappings in Table 3 are consistent with those
   for IP-in-IP tunnels [RFC6040], which ensures backward compatibility
   with all current and past variants of ECN marking (see Section 4).
   It also ensures forward compatibility with any future form of ECN
   marking that complies with the guidelines in [RFC9599], including
   cases where ECT(1) represents a second level of marking severity
   below CE.

   The one exception is that the drop condition in Table 3 need not be
   logged because, with TRILL, it is the result of a valid combination
   of events.

4.  TRILL Support for ECN Variants

   This section is informative, not normative; it discusses interworking
   between TRILL and variants of the standardized form of ECN in IP
   [RFC3168].  See also [RFC8311].

   The ECN wire protocol for TRILL (Section 2) and the ingress
   (Section 3.1) and egress (Section 3.3) ECN behaviors have been
   designed to support the other known variants of ECN as detailed
   below.  New variants of ECN will have to comply with the guidelines
   for defining alternative ECN semantics [RFC4774].  It is expected
   that the TRILL ECN wire protocol is generic enough to support such
   potential future variants.

4.1.  Pre-Congestion Notification (PCN)

   The PCN wire protocol [RFC6660] is recognized by the use of a PCN-
   compatible Diffserv codepoint in the IP header and a nonzero IP-ECN
   field.  For TRILL or any lower-layer protocol, equivalent traffic-
   classification codepoints would have to be defined, but that is
   outside the scope of this document.

   The PCN wire protocol is similar to ECN, except it indicates
   congestion with two levels of severity.  It uses:

   *  11 (CE) as the most severe, termed the Excess-Traffic-Marked (ETM)
      codepoint

   *  01 ECT(1) as a lesser severity level, termed the Threshold-Marked
      (ThM) codepoint.  This difference between ECT(1) and ECT(0) only
      applies to PCN, not to the classic ECN support specified for TRILL
      in this document before Section 4.

   To implement PCN on a transit RBridge would require a detailed
   specification.  In brief:

   *  the TRILL CCE flag would be used for the Excess-Traffic-Marked
      (ETM) codepoint;

   *  ECT(1) in the TRILL-ECN field would be used for the Threshold-
      Marked codepoint.

   Then, the ingress and egress behaviors defined in Section 3 would not
   need to be altered to ensure support for PCN as well as ECN.

4.2.  Low Latency, Low Loss, and Scalable Throughput (L4S)

   L4S is currently on the IETF's experimental track.  An outline of how
   a transit TRILL RBridge would support L4S [RFC9331] is given in
   Appendix A.

5.  IANA Considerations

   IANA has updated the "TRILL Extended Header Flags" registry by
   replacing the lines for bits 9-13 and 21-26 with the following:

   +=======+==============================================+===========+
   | Bits  | Purpose                                      | Reference |
   +=======+==============================================+===========+
   | 9-11  | available non-critical hop-by-hop flags      | [RFC7179] |
   +-------+----------------------------------------------+-----------+
   | 12-13 | TRILL-ECN (Explicit Congestion Notification) | RFC 9600  |
   +-------+----------------------------------------------+-----------+
   | 21-25 | available critical ingress-to-egress flags   | [RFC7179] |
   +-------+----------------------------------------------+-----------+
   | 26    | Critical Congestion Experienced (CCE)        | RFC 9600  |
   +-------+----------------------------------------------+-----------+

         Table 4: Updated "TRILL Extended Header Flags" Registry

6.  Security Considerations

   TRILL support of ECN is a straightforward combination of previously
   specified ECN and TRILL with no significant new security
   considerations.

   For general security considerations regarding adding ECN to lower
   layer protocols, see [RFC9599] and [RFC6040].

   For general TRILL protocol security considerations, see [RFC6325].

7.  References

7.1.  Normative References

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119,
              DOI 10.17487/RFC2119, March 1997,
              <https://www.rfc-editor.org/info/rfc2119>.

   [RFC3168]  Ramakrishnan, K., Floyd, S., and D. Black, "The Addition
              of Explicit Congestion Notification (ECN) to IP",
              RFC 3168, DOI 10.17487/RFC3168, September 2001,
              <https://www.rfc-editor.org/info/rfc3168>.

   [RFC4774]  Floyd, S., "Specifying Alternate Semantics for the
              Explicit Congestion Notification (ECN) Field", BCP 124,
              RFC 4774, DOI 10.17487/RFC4774, November 2006,
              <https://www.rfc-editor.org/info/rfc4774>.

   [RFC6325]  Perlman, R., Eastlake 3rd, D., Dutt, D., Gai, S., and A.
              Ghanwani, "Routing Bridges (RBridges): Base Protocol
              Specification", RFC 6325, DOI 10.17487/RFC6325, July 2011,
              <https://www.rfc-editor.org/info/rfc6325>.

   [RFC7179]  Eastlake 3rd, D., Ghanwani, A., Manral, V., Li, Y., and C.
              Bestler, "Transparent Interconnection of Lots of Links
              (TRILL): Header Extension", RFC 7179,
              DOI 10.17487/RFC7179, May 2014,
              <https://www.rfc-editor.org/info/rfc7179>.

   [RFC7567]  Baker, F., Ed. and G. Fairhurst, Ed., "IETF
              Recommendations Regarding Active Queue Management",
              BCP 197, RFC 7567, DOI 10.17487/RFC7567, July 2015,
              <https://www.rfc-editor.org/info/rfc7567>.

   [RFC7780]  Eastlake 3rd, D., Zhang, M., Perlman, R., Banerjee, A.,
              Ghanwani, A., and S. Gupta, "Transparent Interconnection
              of Lots of Links (TRILL): Clarifications, Corrections, and
              Updates", RFC 7780, DOI 10.17487/RFC7780, February 2016,
              <https://www.rfc-editor.org/info/rfc7780>.

   [RFC8174]  Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
              2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
              May 2017, <https://www.rfc-editor.org/info/rfc8174>.

   [RFC8311]  Black, D., "Relaxing Restrictions on Explicit Congestion
              Notification (ECN) Experimentation", RFC 8311,
              DOI 10.17487/RFC8311, January 2018,
              <https://www.rfc-editor.org/info/rfc8311>.

   [RFC9599]  Briscoe, B. and J. Kaippallimalil, "Guidelines for Adding
              Congestion Notification to Protocols that Encapsulate IP",
              RFC 9599, DOI 10.17487/RFC9599, August 2024,
              <https://www.rfc-editor.org/info/rfc9599>.

7.2.  Informative References

   [IANAthFlags]
              IANA, "TRILL Extended Header Flags",
              <http://www.iana.org/assignments/trill-parameters/>.

   [RFC6040]  Briscoe, B., "Tunnelling of Explicit Congestion
              Notification", RFC 6040, DOI 10.17487/RFC6040, November
              2010, <https://www.rfc-editor.org/info/rfc6040>.

   [RFC6660]  Briscoe, B., Moncaster, T., and M. Menth, "Encoding Three
              Pre-Congestion Notification (PCN) States in the IP Header
              Using a Single Diffserv Codepoint (DSCP)", RFC 6660,
              DOI 10.17487/RFC6660, July 2012,
              <https://www.rfc-editor.org/info/rfc6660>.

   [RFC9331]  De Schepper, K. and B. Briscoe, Ed., "The Explicit
              Congestion Notification (ECN) Protocol for Low Latency,
              Low Loss, and Scalable Throughput (L4S)", RFC 9331,
              DOI 10.17487/RFC9331, January 2023,
              <https://www.rfc-editor.org/info/rfc9331>.

Appendix A.  TRILL Transit RBridge Behavior to Support L4S

   The specification of the Low Latency, Low Loss, and Scalable
   throughput (L4S) wire protocol for IP is given in [RFC9331].  L4S is
   one example of the ways TRILL ECN handling may evolve [RFC8311].  It
   is similar to the original ECN wire protocol for IP [RFC3168],
   except:

   *  An AQM that supports L4S classifies packets with ECT(1) or CE in
      the IP header into an L4S queue and a "Classic" queue otherwise.

   *  The meaning of CE markings applied by an L4S queue is not the same
      as the meaning of a drop by a "Classic" queue (contrary to the
      original requirement for ECN [RFC3168]).  Instead, the likelihood
      that the Classic queue drops packets is defined as the square of
      the likelihood that the L4S queue marks packets -- e.g., when
      there is a drop probability of 0.0009 (0.09%), the L4S marking
      probability will be 0.03 (3%).

   This seems to present a problem for the way that a transit TRILL
   RBridge defers the choice between marking and dropping to the egress.
   Nonetheless, the following pseudocode outlines how a transit TRILL
   RBridge can implement L4S marking in such a way that the egress
   behavior already described in Section 3.3 for Classic ECN [RFC3168]
   will produce the desired outcome.

      /* p is an internal variable calculated by any L4S AQM
       *  dependent on the delay being experienced in the Classic queue.
       * bit13 is the least significant bit of the TRILL-ECN field
       */

      % On TRILL transit
      if (bit13 == 0 ) {
            % Classic Queue
            if (p > max(random(), random()) )
               mark(CCE)                         % likelihood: p^2

      } else {
            % L4S Queue
            if (p > random() ) {
               if (p > random() )
                  mark(CCE)                      % likelihood: p^2
               else
                  mark(NCCE)                     % likelihood: p - p^2
            }
      }

   With the above transit behavior, an egress that supports ECN
   (Section 3.3) will drop packets or propagate their ECN markings
   depending on whether the arriving inner header is from an ECN-capable
   or not ECN-capable transport.

   Even if an egress has no L4S-specific logic of its own, it will drop
   packets with the square of the probability that an egress would if it
   did support ECN, for the following reasons:

   *  Egress with ECN support:

      -  L4S: Propagates both the Critical and Non-Critical CE marks
         (CCE and NCCE) as a CE mark.

         Likelihood: p^2 + p - p^2 = p

      -  Classic: Propagates CCE marks as CE or drop, depending on the
         inner header.

         Likelihood: p^2

   *  Egress without ECN support:

      -  L4S: Does not propagate NCCE as a CE mark, but drops CCE marks.

         Likelihood: p^2

      -  Classic: Drops CCE marks.

         Likelihood: p^2

Acknowledgements

   The helpful comments of Loa Andersson and Adam Roach are hereby
   acknowledged.

Authors' Addresses

   Donald E. Eastlake, 3rd
   Independent
   2386 Panoramic Circle
   Apopka, FL 32703
   United States of America
   Phone: +1-508-333-2270
   Email: d3e3e3@gmail.com