Rfc9085
TitleBorder Gateway Protocol - Link State (BGP-LS) Extensions for Segment Routing
AuthorS. Previdi, K. Talaulikar, Ed., C. Filsfils, H. Gredler, M. Chen
DateAugust 2021
Format:HTML, TXT, PDF, XML
Updated byRFC9356
Status:PROPOSED STANDARD





Internet Engineering Task Force (IETF)                        S. Previdi
Request for Comments: 9085                           Huawei Technologies
Category: Standards Track                             K. Talaulikar, Ed.
ISSN: 2070-1721                                              C. Filsfils
                                                     Cisco Systems, Inc.
                                                              H. Gredler
                                                            RtBrick Inc.
                                                                 M. Chen
                                                     Huawei Technologies
                                                             August 2021


  Border Gateway Protocol - Link State (BGP-LS) Extensions for Segment
                                Routing

Abstract

   Segment Routing (SR) allows for a flexible definition of end-to-end
   paths by encoding paths as sequences of topological subpaths, called
   "segments".  These segments are advertised by routing protocols,
   e.g., by the link-state routing protocols (IS-IS, OSPFv2, and OSPFv3)
   within IGP topologies.

   This document defines extensions to the Border Gateway Protocol -
   Link State (BGP-LS) address family in order to carry SR information
   via BGP.

Status of This Memo

   This is an Internet Standards Track document.

   This document is a product of the Internet Engineering Task Force
   (IETF).  It represents the consensus of the IETF community.  It has
   received public review and has been approved for publication by the
   Internet Engineering Steering Group (IESG).  Further information on
   Internet Standards is available in Section 2 of RFC 7841.

   Information about the current status of this document, any errata,
   and how to provide feedback on it may be obtained at
   https://www.rfc-editor.org/info/rfc9085.

Copyright Notice

   Copyright (c) 2021 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (https://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Table of Contents

   1.  Introduction
     1.1.  Requirements Language
   2.  BGP-LS Extensions for Segment Routing
     2.1.  Node Attribute TLVs
       2.1.1.  SID/Label TLV
       2.1.2.  SR Capabilities TLV
       2.1.3.  SR-Algorithm TLV
       2.1.4.  SR Local Block TLV
       2.1.5.  SRMS Preference TLV
     2.2.  Link Attribute TLVs
       2.2.1.  Adjacency SID TLV
       2.2.2.  LAN Adjacency SID TLV
       2.2.3.  L2 Bundle Member Attributes TLV
     2.3.  Prefix Attribute TLVs
       2.3.1.  Prefix-SID TLV
       2.3.2.  Prefix Attribute Flags TLV
       2.3.3.  Source Router Identifier TLV
       2.3.4.  Source OSPF Router-ID TLV
       2.3.5.  Range TLV
     2.4.  Equivalent IS-IS Segment Routing TLVs/Sub-TLVs
     2.5.  Equivalent OSPFv2/OSPFv3 Segment Routing TLVs/Sub-TLVs
   3.  IANA Considerations
     3.1.  TLV/Sub-TLV Code Points Summary
   4.  Manageability Considerations
   5.  Security Considerations
   6.  References
     6.1.  Normative References
     6.2.  Informative References
   Acknowledgements
   Contributors
   Authors' Addresses

1.  Introduction

   Segment Routing (SR) allows for a flexible definition of end-to-end
   paths by combining subpaths called "segments".  A segment can
   represent any instruction: topological or service based.  A segment
   can have a local semantic to an SR node or global semantic within a
   domain.  Within IGP topologies, an SR path is encoded as a sequence
   of topological subpaths, called "IGP segments".  These segments are
   advertised by the link-state routing protocols (IS-IS, OSPFv2, and
   OSPFv3).

   [RFC8402] defines the link-state IGP segments -- prefix, node,
   anycast, and adjacency segments.  Prefix segments, by default,
   represent an ECMP-aware shortest-path to a prefix, as per the state
   of the IGP topology.  Adjacency segments represent a hop over a
   specific adjacency between two nodes in the IGP.  A prefix segment is
   typically a multi-hop path while an adjacency segment, in most of the
   cases, is a one-hop path.  Node and anycast segments are variations
   of the prefix segment with their specific characteristics.

   When SR is enabled in an IGP domain, segments are advertised in the
   form of Segment Identifiers (SIDs).  The IGP link-state routing
   protocols have been extended to advertise SIDs and other SR-related
   information.  IGP extensions are described for: IS-IS [RFC8667],
   OSPFv2 [RFC8665], and OSPFv3 [RFC8666].  Using these extensions, SR
   can be enabled within an IGP domain.

   SR allows advertisement of single or multi-hop paths.  The flooding
   scope for the IGP extensions for SR is IGP area-wide.  Consequently,
   the contents of a Link-State Database (LSDB) or a Traffic Engineering
   Database (TED) has the scope of an IGP area; therefore, by using the
   IGP alone, it is not enough to construct segments across multiple IGP
   area or Autonomous System (AS) boundaries.

   In order to address the need for applications that require
   topological visibility across IGP areas, or even across ASes, the
   BGP-LS address family / subaddress family have been defined to allow
   BGP to carry link-state information.  The BGP Network Layer
   Reachability Information (NLRI) encoding format for BGP-LS and a new
   BGP Path Attribute called the "BGP-LS Attribute" are defined in
   [RFC7752].  The identifying key of each link-state object, namely a
   node, link, or prefix, is encoded in the NLRI, and the properties of
   the object are encoded in the BGP-LS Attribute.

                           +------------+
                           |  Consumer  |
                           +------------+
                                 ^
                                 |
                                 v
                       +-------------------+
                       |    BGP Speaker    |         +-----------+
                       | (Route Reflector) |         | Consumer  |
                       +-------------------+         +-----------+
                             ^   ^   ^                       ^
                             |   |   |                       |
             +---------------+   |   +-------------------+   |
             |                   |                       |   |
             v                   v                       v   v
       +-----------+       +-----------+             +-----------+
       |    BGP    |       |    BGP    |             |    BGP    |
       |  Speaker  |       |  Speaker  |    . . .    |  Speaker  |
       +-----------+       +-----------+             +-----------+
             ^                   ^                         ^
             |                   |                         |
            IGP                 IGP                       IGP

                Figure 1: Link-State Information Collection

   Figure 1 denotes a typical deployment scenario.  In each IGP area,
   one or more nodes are configured with BGP-LS.  These BGP speakers
   form an Internal BGP (IBGP) mesh by connecting to one or more route
   reflectors.  This way, all BGP speakers (specifically the route
   reflectors) obtain link-state information from all IGP areas (and
   from other ASes from External BGP (EBGP) peers).  An external
   component connects to the route reflector to obtain this information
   (perhaps moderated by a policy regarding what information is or isn't
   advertised to the external component) as described in [RFC7752].

   This document describes extensions to BGP-LS to advertise the SR
   information.  An external component (e.g., a controller) can collect
   SR information from across an SR domain (as described in [RFC8402])
   and construct the end-to-end path (with its associated SIDs) that
   needs to be applied to an incoming packet to achieve the desired end-
   to-end forwarding.  SR operates within a trusted domain consisting of
   a single AS or multiple ASes managed by the same administrative
   entity, e.g., within a single provider network.

1.1.  Requirements Language

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
   "OPTIONAL" in this document are to be interpreted as described in BCP
   14 [RFC2119] [RFC8174] when, and only when, they appear in all
   capitals, as shown here.

2.  BGP-LS Extensions for Segment Routing

   This document defines SR extensions to BGP-LS and specifies the TLVs
   and sub-TLVs for advertising SR information within the BGP-LS
   Attribute.  Sections 2.4 and 2.5 list the equivalent TLVs and sub-
   TLVs in the IS-IS, OSPFv2, and OSPFv3 protocols.

   BGP-LS [RFC7752] defines the BGP-LS NLRI that can be a Node NLRI, a
   Link NLRI, or a Prefix NLRI, and it defines the TLVs that map link-
   state information to BGP-LS NLRI within the BGP-LS Attribute.  This
   document adds additional BGP-LS Attribute TLVs in order to encode SR
   information.  It does not introduce any changes to the encoding of
   the BGP-LS NLRIs.

2.1.  Node Attribute TLVs

   The following Node Attribute TLVs are defined:

                +======+=================+===============+
                | Type | Description     | Section       |
                +======+=================+===============+
                | 1161 | SID/Label       | Section 2.1.1 |
                +------+-----------------+---------------+
                | 1034 | SR Capabilities | Section 2.1.2 |
                +------+-----------------+---------------+
                | 1035 | SR Algorithm    | Section 2.1.3 |
                +------+-----------------+---------------+
                | 1036 | SR Local Block  | Section 2.1.4 |
                +------+-----------------+---------------+
                | 1037 | SRMS Preference | Section 2.1.5 |
                +------+-----------------+---------------+

                       Table 1: Node Attribute TLVs

   These TLVs should only be added to the BGP-LS Attribute associated
   with the Node NLRI that describes the IGP node that is originating
   the corresponding IGP TLV/sub-TLV described below.

2.1.1.  SID/Label TLV

   The SID/Label TLV is used as a sub-TLV by the SR Capabilities
   (Section 2.1.2) and Segment Routing Local Block (SRLB)
   (Section 2.1.4) TLVs.  This information is derived from the protocol-
   specific advertisements.

   *  IS-IS, as defined by the SID/Label Sub-TLV in Section 2.3 of
      [RFC8667].

   *  OSPFv2/OSPFv3, as defined by the SID/Label Sub-TLV in Section 2.1
      of [RFC8665] and Section 3.1 of [RFC8666].

   The TLV has the following format:

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |               Type            |            Length             |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                      SID/Label (variable)                    //
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                       Figure 2: SID/Label TLV Format

   Where:

   Type:  1161

   Length:  Variable.  Either 3 or 4 octets depending on whether the
      value is encoded as a label or as an index/SID.

   SID/Label:  If the length is set to 3, then the 20 rightmost bits
      represent a label (the total TLV size is 7), and the 4 leftmost
      bits are set to 0.  If the length is set to 4, then the value
      represents a 32-bit SID (the total TLV size is 8).

2.1.2.  SR Capabilities TLV

   The SR Capabilities TLV is used in order to advertise the node's SR
   capabilities including its Segment Routing Global Base (SRGB)
   range(s).  In the case of IS-IS, the capabilities also include the
   IPv4 and IPv6 support for the SR-MPLS forwarding plane.  This
   information is derived from the protocol-specific advertisements.

   *  IS-IS, as defined by the SR-Capabilities Sub-TLV in Section 3.1 of
      [RFC8667].

   *  OSPFv2/OSPFv3, as defined by the SID/Label Range TLV in
      Section 3.2 of [RFC8665].  OSPFv3 leverages the same TLV as
      defined for OSPFv2.

   The SR Capabilities TLV has the following format:

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |               Type            |          Length               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |      Flags    |   Reserved    |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                  Range Size 1                 |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                SID/Label Sub-TLV 1                           //
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   ...

   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                  Range Size N                 |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                SID/Label Sub-TLV N                           //
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                    Figure 3: SR Capabilities TLV Format

   Where:

   Type:  1034

   Length:  Variable.  The minimum length is 12 octets.

   Flags:  1 octet of flags as defined in Section 3.1 of [RFC8667] for
      IS-IS.  The flags are not currently defined for OSPFv2 and OSPFv3
      and MUST be set to 0 and ignored on receipt.

   Reserved:  1 octet that MUST be set to 0 and ignored on receipt.

   One or more entries, each of which have the following format:

      Range Size:  3 octets with a non-zero value indicating the number
         of labels in the range.

      SID/Label TLV:  (as defined in Section 2.1.1) used as a sub-TLV,
         which encodes the first label in the range.  Since the SID/
         Label TLV is used to indicate the first label of the SRGB
         range, only label encoding is valid under the SR Capabilities
         TLV.

2.1.3.  SR-Algorithm TLV

   The SR-Algorithm TLV is used in order to advertise the SR algorithms
   supported by the node.  This information is derived from the
   protocol-specific advertisements.

   *  IS-IS, as defined by the SR-Algorithm Sub-TLV in Section 3.2 of
      [RFC8667].

   *  OSPFv2/OSPFv3, as defined by the SR-Algorithm TLV in Section 3.1
      of [RFC8665].  OSPFv3 leverages the same TLV as defined for
      OSPFv2.

   The SR-Algorithm TLV has the following format:

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |            Type               |            Length             |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |  Algorithm 1  |  Algorithm... |  Algorithm N  |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                     Figure 4: SR-Algorithm TLV Format

   Where:

   Type:  1035

   Length:  Variable.  The minimum length is 1 octet and the maximum can
      be 256.

   Algorithm:  One or more fields of 1 octet each that identifies the
      algorithm.

2.1.4.  SR Local Block TLV

   The SRLB TLV contains the range(s) of labels the node has reserved
   for local SIDs.  Local SIDs are used, e.g., in IGP (IS-IS, OSPF) for
   Adjacency SIDs and may also be allocated by components other than IGP
   protocols.  As an example, an application or a controller may
   instruct a node to allocate a specific local SID.  Therefore, in
   order for such applications or controllers to know the range of local
   SIDs available, the node is required to advertise its SRLB.

   This information is derived from the protocol-specific
   advertisements.

   *  IS-IS, as defined by the SRLB Sub-TLV in Section 3.3 of [RFC8667].

   *  OSPFv2/OSPFv3, as defined by the SR Local Block TLV in Section 3.3
      of [RFC8665].  OSPFv3 leverages the same TLV as defined for
      OSPFv2.

   The SRLB TLV has the following format:

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |               Type            |               Length          |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |      Flags    |   Reserved    |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |              Sub-Range Size 1                 |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                SID/Label Sub-TLV 1                           //
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   ...

   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |              Sub-Range Size N                 |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                SID/Label Sub-TLV N                           //
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                         Figure 5: SRLB TLV Format

   Where:

   Type:  1036

   Length:  Variable.  The minimum length is 12 octets.

   Flags:  1 octet of flags.  The flags are as defined in Section 3.3 of
      [RFC8667] for IS-IS.  The flags are not currently defined for
      OSPFv2 and OSPFv3 and MUST be set to 0 and ignored on receipt.

   Reserved:  1 octet that MUST be set to 0 and ignored on receipt.

   One or more entries corresponding to a sub-range(s), each of which
   have the following format:

      Range Size:  3-octet value indicating the number of labels in the
         range.

      SID/Label TLV:  (as defined in Section 2.1.1) used as a sub-TLV,
         which encodes the first label in the sub-range.  Since the SID/
         Label TLV is used to indicate the first label of the SRLB sub-
         range, only label encoding is valid under the SR Local Block
         TLV.

2.1.5.  SRMS Preference TLV

   The Segment Routing Mapping Server (SRMS) Preference TLV is used in
   order to associate a preference with SRMS advertisements from a
   particular source.  [RFC8661] specifies the SRMS functionality along
   with the SRMS preference of the node advertising the SRMS Prefix-to-
   SID mapping ranges.

   This information is derived from the protocol-specific
   advertisements.

   *  IS-IS, as defined by the SRMS Preference Sub-TLV in Section 3.4 of
      [RFC8667].

   *  OSPFv2/OSPFv3, as defined by the SRMS Preference TLV in
      Section 3.4 of [RFC8665].  OSPFv3 leverages the same TLV as
      defined for OSPFv2.

   The SRMS Preference TLV has the following format:

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |            Type               |            Length             |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   | Preference    |
   +-+-+-+-+-+-+-+-+

                    Figure 6: SRMS Preference TLV Format

   Where:

   Type:  1037

   Length:  1 octet

   Preference:  1 octet carrying an unsigned 8-bit SRMS preference.

2.2.  Link Attribute TLVs

   The following Link Attribute TLVs are defined:

        +======+=================================+===============+
        | Type | Description                     | Section       |
        +======+=================================+===============+
        | 1099 | Adjacency SID TLV               | Section 2.2.1 |
        +------+---------------------------------+---------------+
        | 1100 | LAN Adjacency SID TLV           | Section 2.2.2 |
        +------+---------------------------------+---------------+
        | 1172 | L2 Bundle Member Attributes TLV | Section 2.2.3 |
        +------+---------------------------------+---------------+

                       Table 2: Link Attribute TLVs

   These TLVs should only be added to the BGP-LS Attribute associated
   with the Link NLRI that describes the link of the IGP node that is
   originating the corresponding IGP TLV/sub-TLV described below.

2.2.1.  Adjacency SID TLV

   The Adjacency SID TLV is used in order to advertise information
   related to an Adjacency SID.  This information is derived from the
   Adj-SID Sub-TLV of IS-IS (Section 2.2.1 of [RFC8667]), OSPFv2
   (Section 6.1 of [RFC8665]), and OSPFv3 (Section 7.1 of [RFC8666]).

   The Adjacency SID TLV has the following format:

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |               Type            |              Length           |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   | Flags         |     Weight    |             Reserved          |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                   SID/Label/Index (variable)                 //
   +---------------------------------------------------------------+

                     Figure 7: Adjacency SID TLV Format

   Where:

   Type:  1099

   Length:  Variable.  Either 7 or 8 octets depending on the label or
      index encoding of the SID.

   Flags:  1-octet value that should be set as:

      *  IS-IS Adj-SID flags as defined in Section 2.2.1 of [RFC8667].

      *  OSPFv2 Adj-SID flags as defined in Section 6.1 of [RFC8665].

      *  OSPFv3 Adj-SID flags as defined in Section 7.1 of [RFC8666].

   Weight:  1 octet carrying the weight used for load-balancing
      purposes.  The use of weight is described in Section 3.4 of
      [RFC8402].

   Reserved:  2 octets that MUST be set to 0 and ignored on receipt.

   SID/Index/Label:

      IS-IS:  Label or index value as defined in Section 2.2.1 of
         [RFC8667].

      OSPFv2:  Label or index value as defined in Section 6.1 of
         [RFC8665].

      OSPFv3:  Label or index value as defined in Section 7.1 of
         [RFC8666].

   The Flags and, as an extension, the SID/Index/Label fields of this
   TLV are interpreted according to the respective underlying IS-IS,
   OSPFv2, or OSPFv3 protocol.  The Protocol-ID of the BGP-LS Link NLRI
   is used to determine the underlying protocol specification for
   parsing these fields.

2.2.2.  LAN Adjacency SID TLV

   For a LAN, normally a node only announces its adjacency to the IS-IS
   pseudonode (or the equivalent OSPF Designated and Backup Designated
   Routers).  The LAN Adjacency SID TLV allows a node to announce
   adjacencies to all other nodes attached to the LAN in a single
   instance of the BGP-LS Link NLRI.  Without this TLV, the
   corresponding BGP-LS Link NLRI would need to be originated for each
   additional adjacency in order to advertise the SR TLVs for these
   neighbor adjacencies.

   This information is derived from the LAN-Adj-SID Sub-TLV of IS-IS
   (Section 2.2.2 of [RFC8667]), the LAN Adj-SID Sub-TLV of OSPFv2
   (Section 6.2 of [RFC8665]), and the LAN Adj-SID Sub-TLV of OSPFv3
   (Section 7.2 of [RFC8666]).

   The LAN Adjacency SID TLV has the following format:

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |              Type             |            Length             |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |     Flags     |     Weight    |            Reserved           |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |             OSPF Neighbor ID / IS-IS System ID                |
   +                               +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                    SID/Label/Index (variable)                //
   +---------------------------------------------------------------+

                   Figure 8: LAN Adjacency SID TLV Format

   Where:

   Type:  1100

   Length:  Variable.  For IS-IS, it would be 13 or 14 octets depending
      on the label or index encoding of the SID.  For OSPF, it would be
      11 or 12 octets depending on the label or index encoding of the
      SID.

   Flags:  1-octet value that should be set as:

      *  IS-IS LAN Adj-SID flags as defined in Section 2.2.2 of
         [RFC8667].

      *  OSPFv2 LAN Adj-SID flags as defined in Section 6.2 of
         [RFC8665].

      *  OSPFv3 LAN Adj-SID flags as defined in Section 7.2 of
         [RFC8666].

   Weight:  1 octet carrying the weight used for load-balancing
      purposes.  The use of weight is described in Section 3.4 of
      [RFC8402].

   Reserved:  2 octets that MUST be set to 0 and ignored on receipt.

   Neighbor ID:  6 octets for IS-IS for the System ID, and 4 octets for
      OSPF for the OSPF Router-ID of the neighbor.

   SID/Index/Label:

      IS-IS:  Label or index value as defined in Section 2.2.2 of
         [RFC8667].

      OSPFv2:  Label or index value as defined in Section 6.2 of
         [RFC8665].

      OSPFv3:  Label or index value as defined in Section 7.2 of
         [RFC8666].

   The Neighbor ID, Flags, and, as an extension, the SID/Index/Label
   fields of this TLV are interpreted according to the respective
   underlying IS-IS, OSPFv2, or OSPFv3 protocol.  The Protocol-ID of the
   BGP-LS Link NLRI is used to determine the underlying protocol
   specification for parsing these fields.

2.2.3.  L2 Bundle Member Attributes TLV

   The L2 Bundle Member Attributes TLV identifies an L2 Bundle Member
   link, which in turn is associated with a parent L3 link.  The L3 link
   is described by the Link NLRI defined in [RFC7752], and the L2 Bundle
   Member Attributes TLV is associated with the Link NLRI.  The TLV MAY
   include sub-TLVs that describe attributes associated with the bundle
   member.  The identified bundle member represents a unidirectional
   path from the originating router to the neighbor specified in the
   parent L3 link.  Multiple L2 Bundle Member Attributes TLVs MAY be
   associated with a Link NLRI.

   This information is derived from L2 Bundle Member Attributes TLV of
   IS-IS (Section 2 of [RFC8668]).  The equivalent functionality has not
   been specified as yet for OSPF.

   The L2 Bundle Member Attributes TLV has the following format:

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |               Type            |          Length               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                     L2 Bundle Member Descriptor               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                  Link Attribute Sub-TLVs(variable)          //
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

              Figure 9: L2 Bundle Member Attributes TLV Format

   Where:

   Type:  1172

   Length:  Variable.

   L2 Bundle Member Descriptor:  4-octet field that carries a link-local
      identifier as defined in [RFC4202].

   Link attributes for L2 Bundle Member links are advertised as sub-TLVs
   of the L2 Bundle Member Attributes TLV.  The sub-TLVs are identical
   to existing BGP-LS TLVs as identified in the table below.

    +================+==========================+====================+
    | TLV Code Point | Description              | Reference Document |
    +================+==========================+====================+
    |      1088      | Administrative group     | [RFC7752]          |
    |                | (color)                  |                    |
    +----------------+--------------------------+--------------------+
    |      1089      | Maximum link bandwidth   | [RFC7752]          |
    +----------------+--------------------------+--------------------+
    |      1090      | Max. reservable link     | [RFC7752]          |
    |                | bandwidth                |                    |
    +----------------+--------------------------+--------------------+
    |      1091      | Unreserved bandwidth     | [RFC7752]          |
    +----------------+--------------------------+--------------------+
    |      1092      | TE default metric        | [RFC7752]          |
    +----------------+--------------------------+--------------------+
    |      1093      | Link protection type     | [RFC7752]          |
    +----------------+--------------------------+--------------------+
    |      1099      | Adjacency Segment        | Section 2.2.1      |
    |                | Identifier (Adj-SID) TLV |                    |
    +----------------+--------------------------+--------------------+
    |      1100      | LAN Adjacency Segment    | Section 2.2.2      |
    |                | Identifier (Adj-SID) TLV |                    |
    +----------------+--------------------------+--------------------+
    |      1114      | Unidirectional link      | [RFC8571]          |
    |                | delay                    |                    |
    +----------------+--------------------------+--------------------+
    |      1115      | Min/Max Unidirectional   | [RFC8571]          |
    |                | link delay               |                    |
    +----------------+--------------------------+--------------------+
    |      1116      | Unidirectional Delay     | [RFC8571]          |
    |                | Variation                |                    |
    +----------------+--------------------------+--------------------+
    |      1117      | Unidirectional Link Loss | [RFC8571]          |
    +----------------+--------------------------+--------------------+
    |      1118      | Unidirectional residual  | [RFC8571]          |
    |                | bandwidth                |                    |
    +----------------+--------------------------+--------------------+
    |      1119      | Unidirectional available | [RFC8571]          |
    |                | bandwidth                |                    |
    +----------------+--------------------------+--------------------+
    |      1120      | Unidirectional Utilized  | [RFC8571]          |
    |                | Bandwidth                |                    |
    +----------------+--------------------------+--------------------+

       Table 3: BGP-LS Attribute TLVs are also used as sub-TLVs of
                   the L2 Bundle Member Attributes TLV

2.3.  Prefix Attribute TLVs

   The following Prefix Attribute TLVs are defined:

            +======+==========================+===============+
            | Type | Description              | Section       |
            +======+==========================+===============+
            | 1158 | Prefix-SID               | Section 2.3.1 |
            +------+--------------------------+---------------+
            | 1159 | Range                    | Section 2.3.5 |
            +------+--------------------------+---------------+
            | 1170 | Prefix Attribute Flags   | Section 2.3.2 |
            +------+--------------------------+---------------+
            | 1171 | Source Router Identifier | Section 2.3.3 |
            +------+--------------------------+---------------+
            | 1174 | Source OSPF Router-ID    | Section 2.3.4 |
            +------+--------------------------+---------------+

                       Table 4: Prefix Attribute TLVs

   These TLVs should only be added to the BGP-LS Attribute associated
   with the Prefix NLRI that describes the prefix of the IGP node that
   is originating the corresponding IGP TLV/sub-TLV described below.

2.3.1.  Prefix-SID TLV

   The Prefix-SID TLV is used in order to advertise information related
   to a Prefix-SID.  This information is derived from the Prefix-SID
   Sub-TLV of IS-IS (Section 2.1 of [RFC8667]), the Prefix-SID Sub-TLV
   of OSPFv2 (Section 5 of [RFC8665]), and the Prefix-SID Sub-TLV of
   OSPFv3 (Section 6 of [RFC8666]).

   The Prefix-SID TLV has the following format:

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |               Type            |            Length             |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |     Flags     |   Algorithm   |           Reserved            |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                       SID/Index/Label (variable)             //
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                      Figure 10: Prefix-SID TLV Format

   Where:

   Type:  1158

   Length:  Variable. 7 or 8 octets depending on the label or index
      encoding of the SID.

   Flags:  1-octet value that should be set as:

      *  IS-IS Prefix-SID flags as defined in Section 2.1.1 of
         [RFC8667].

      *  OSPFv2 Prefix-SID flags as defined in Section 5 of [RFC8665].

      *  OSPFv3 Prefix-SID flags as defined in Section 6 of [RFC8665].

   Algorithm:  1-octet value identifies the algorithm.  The semantics of
      the algorithm are described in Section 3.1.1 of [RFC8402].

   Reserved:  2 octets that MUST be set to 0 and ignored on receipt.

   SID/Index/Label:

      IS-IS:  Label or index value as defined in Section 2.1 of
         [RFC8667].

      OSPFv2:  Label or index value as defined in Section 5 of
         [RFC8665].

      OSPFv3:  Label or index value as defined in Section 6 of
         [RFC8666].

   The Flags and, as an extension, the SID/Index/Label fields of this
   TLV are interpreted according to the respective underlying IS-IS,
   OSPFv2, or OSPFv3 protocol.  The Protocol-ID of the BGP-LS Prefix
   NLRI is used to determine the underlying protocol specification for
   parsing these fields.

2.3.2.  Prefix Attribute Flags TLV

   The Prefix Attribute Flags TLV carries IPv4/IPv6 prefix attribute
   flags information.  These flags are defined for OSPFv2 in Section 2.1
   of [RFC7684], OSPFv3 in Appendix A.4.1.1 of [RFC5340], and IS-IS in
   Section 2.1 of [RFC7794].

   The Prefix Attribute Flags TLV has the following format:

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |            Type               |            Length             |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                        Flags (variable)                      //
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                Figure 11: Prefix Attribute Flags TLV Format

   Where:

   Type:  1170

   Length:  Variable.

   Flags:  a variable-length Flag field (according to the Length field).
      Flags are routing protocol specific and are to be set as below:

      *  IS-IS flags correspond to the IPv4/IPv6 Extended Reachability
         Attribute Flags defined in Section 2.1 of [RFC7794].  In the
         case of the X-flag when associated with IPv6 prefix
         reachability, the setting corresponds to the setting of the
         X-flag in the fixed format of IS-IS TLVs 236 [RFC5308] and 237
         [RFC5120].

      *  OSPFv2 flags correspond to the Flags field of the OSPFv2
         Extended Prefix TLV defined in Section 2.1 of [RFC7684].

      *  OSPFv3 flags map to the Prefix Options field defined in
         Appendix A.4.1.1 of [RFC5340] and extended in Section 3.1 of
         [RFC8362].

   The Flags field of this TLV is interpreted according to the
   respective underlying IS-IS, OSPFv2, or OSPFv3 protocol.  The
   Protocol-ID of the BGP-LS Prefix NLRI is used to determine the
   underlying protocol specification for parsing this field.

2.3.3.  Source Router Identifier TLV

   The Source Router Identifier TLV contains the IPv4 or IPv6 Router
   Identifier of the originator of the prefix.  For the IS-IS protocol,
   this is derived from the IPv4/IPv6 Source Router ID Sub-TLV as
   defined in Section 2.2 of [RFC7794].  For the OSPF protocol, this is
   derived from the Prefix Source Router Address Sub-TLV as defined in
   Section 2.2 of [RFC9084].

   The Source Router Identifier TLV has the following format:

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |            Type               |            Length             |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                   4- or 16-octet Router Identifier           //
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

               Figure 12: Source Router Identifier TLV Format

   Where:

   Type:  1171

   Length:  Variable. 4 or 16 octets for the IPv4 or IPv6 prefix,
      respectively.

   Router-ID:  the IPv4 or IPv6 Router-ID in the case of IS-IS, and the
      IPv4 or IPv6 Router Address in the case of OSPF.

2.3.4.  Source OSPF Router-ID TLV

   The Source OSPF Router-ID TLV is applicable only for the OSPF
   protocol and contains the OSPF Router-ID of the originator of the
   prefix.  It is derived from the Prefix Source OSPF Router-ID Sub-TLV
   as defined in Section 2.1 of [RFC9084].

   The Source OSPF Router-ID TLV has the following format:

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |            Type               |            Length             |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                    4-octet OSPF Router-ID                    //
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                Figure 13: Source OSPF Router-ID TLV Format

   Where:

   Type:  1174

   Length:  4 octets

   OSPF Router-ID:  the OSPF Router-ID of the node originating the
      prefix.

2.3.5.  Range TLV

   The Range TLV is used in order to advertise a range of prefix-to-SID
   mappings as part of the SRMS functionality [RFC8661], as defined in
   the respective underlying IGP SR extensions: Section 4 of [RFC8665],
   Section 5 of [RFC8666], and Section 2.4 of [RFC8667].  The
   information advertised in the Range TLV is derived from the SID/Label
   Binding TLV in the case of IS-IS and the OSPFv2/OSPFv3 Extended
   Prefix Range TLV in the case of OSPFv2/OSPFv3.

   A Prefix NLRI, that has been advertised with a Range TLV, is
   considered a normal routing prefix (i.e., prefix reachability) only
   when there is also an IGP metric TLV (TLV 1095) associated it.
   Otherwise, it is considered only as the first prefix in the range for
   prefix-to-SID mapping advertisement.

   The format of the Range TLV is as follows:

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |             Type              |             Length            |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |     Flags     | Reserved      |             Range Size        |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                           sub-TLVs                           //
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                        Figure 14: Range TLV Format

   Where:

   Type:  1159

   Length:  Variable. 11 or 12 octets depending on the label or index
      encoding of the SID.

   Flags:  1-octet value that should be set as:

      *  IS-IS SID/Label Binding TLV flags as defined in Section 2.4.1
         of [RFC8667].

      *  OSPFv2 OSPF Extended Prefix Range TLV flags as defined in
         Section 4 of [RFC8665].

      *  OSPFv3 Extended Prefix Range TLV flags as defined in Section 5
         of [RFC8666].

   Reserved:  1 octet that MUST be set to 0 and ignored on receipt.

   Range Size:  2 octets that carry the number of prefixes that are
      covered by the advertisement.

   The Flags field of this TLV is interpreted according to the
   respective underlying IS-IS, OSPFv2, or OSPFv3 protocol.  The
   Protocol-ID of the BGP-LS Prefix NLRI is used to determine the
   underlying protocol specification for parsing this field.

   The prefix-to-SID mappings are advertised using sub-TLVs as below:

   IS-IS:
      SID/Label Range TLV
         Prefix-SID Sub-TLV

   OSPFv2/OSPFv3:
      OSPFv2/OSPFv3 Extended Prefix Range TLV
         Prefix-SID Sub-TLV

   BGP-LS:
      Range TLV
         Prefix-SID TLV (used as a sub-TLV in this context)

   The prefix-to-SID mapping information for the BGP-LS Prefix-SID TLV
   (used as a sub-TLV in this context) is encoded as described in
   Section 2.3.1.

2.4.  Equivalent IS-IS Segment Routing TLVs/Sub-TLVs

   This section illustrates the IS-IS Segment Routing Extensions TLVs
   and sub-TLVs mapped to the ones defined in this document.

   For each BGP-LS TLV, the following table illustrates its equivalence
   in IS-IS.

   +========================+==============================+===========+
   | Description            | IS-IS TLV/sub-TLV            | Reference |
   +========================+==============================+===========+
   | SR Capabilities        | SR-Capabilities Sub-TLV (2)  | [RFC8667] |
   +------------------------+------------------------------+-----------+
   | SR Algorithm           | SR-Algorithm Sub-TLV (19)    | [RFC8667] |
   +------------------------+------------------------------+-----------+
   | SR Local Block         | SR Local Block Sub-TLV (22)  | [RFC8667] |
   +------------------------+------------------------------+-----------+
   | SRMS Preference        | SRMS Preference Sub-TLV (19) | [RFC8667] |
   +------------------------+------------------------------+-----------+
   | Adjacency SID          | Adj-SID Sub-TLV (31)         | [RFC8667] |
   +------------------------+------------------------------+-----------+
   | LAN Adjacency SID      | LAN-Adj-SID Sub-TLV (32)     | [RFC8667] |
   +------------------------+------------------------------+-----------+
   | Prefix-SID             | Prefix-SID Sub-TLV (3)       | [RFC8667] |
   +------------------------+------------------------------+-----------+
   | Range                  | SID/Label Binding TLV (149)  | [RFC8667] |
   +------------------------+------------------------------+-----------+
   | SID/Label              | SID/Label Sub-TLV (1)        | [RFC8667] |
   +------------------------+------------------------------+-----------+
   | Prefix Attribute       | Prefix Attribute Flags Sub-  | [RFC7794] |
   | Flags                  | TLV (4)                      |           |
   +------------------------+------------------------------+-----------+
   | Source Router          | IPv4/IPv6 Source Router ID   | [RFC7794] |
   | Identifier             | Sub-TLV (11/12)              |           |
   +------------------------+------------------------------+-----------+
   | L2 Bundle Member       | L2 Bundle Member Attributes  | [RFC8668] |
   | Attributes             | TLV (25)                     |           |
   +------------------------+------------------------------+-----------+

          Table 5: IS-IS Segment Routing Extensions TLVs/Sub-TLVs

2.5.  Equivalent OSPFv2/OSPFv3 Segment Routing TLVs/Sub-TLVs

   This section illustrates the OSPFv2 and OSPFv3 Segment Routing
   Extensions TLVs and sub-TLVs mapped to the ones defined in this
   document.

   For each BGP-LS TLV, the following tables illustrate its equivalence
   in OSPFv2 and OSPFv3.

       +===================+==========================+===========+
       | Description       | OSPFv2 TLV/sub-TLV       | Reference |
       +===================+==========================+===========+
       | SR Capabilities   | SID/Label Range TLV (9)  | [RFC8665] |
       +-------------------+--------------------------+-----------+
       | SR Algorithm      | SR-Algorithm TLV (8)     | [RFC8665] |
       +-------------------+--------------------------+-----------+
       | SR Local Block    | SR Local Block TLV (14)  | [RFC8665] |
       +-------------------+--------------------------+-----------+
       | SRMS Preference   | SRMS Preference TLV (15) | [RFC8665] |
       +-------------------+--------------------------+-----------+
       | Adjacency SID     | Adj-SID Sub-TLV (2)      | [RFC8665] |
       +-------------------+--------------------------+-----------+
       | LAN Adjacency SID | LAN Adj-SID Sub-TLV (3)  | [RFC8665] |
       +-------------------+--------------------------+-----------+
       | Prefix-SID        | Prefix-SID Sub-TLV (2)   | [RFC8665] |
       +-------------------+--------------------------+-----------+
       | Range             | OSPF Extended Prefix     | [RFC8665] |
       |                   | Range TLV (2)            |           |
       +-------------------+--------------------------+-----------+
       | SID/Label         | SID/Label Sub-TLV (1)    | [RFC8665] |
       +-------------------+--------------------------+-----------+
       | Prefix Attribute  | Flags of OSPFv2 Extended | [RFC7684] |
       | Flags             | Prefix TLV (1)           |           |
       +-------------------+--------------------------+-----------+
       | Source Router     | Prefix Source Router     | [RFC9084] |
       | Identifier        | Address Sub-TLV (5)      |           |
       +-------------------+--------------------------+-----------+
       | Source OSPF       | Prefix Source OSPF       | [RFC9084] |
       | Router-ID         | Router-ID Sub-TLV (4)    |           |
       +-------------------+--------------------------+-----------+

         Table 6: OSPFv2 Segment Routing Extensions TLVs/Sub-TLVs

       +===================+==========================+===========+
       | Description       | OSPFv3 TLV/sub-TLV       | Reference |
       +===================+==========================+===========+
       | SR Capabilities   | SID/Label Range TLV (9)  | [RFC8665] |
       +-------------------+--------------------------+-----------+
       | SR Algorithm      | SR-Algorithm TLV (8)     | [RFC8665] |
       +-------------------+--------------------------+-----------+
       | SR Local Block    | SR Local Block TLV (14)  | [RFC8665] |
       +-------------------+--------------------------+-----------+
       | SRMS Preference   | SRMS Preference TLV (15) | [RFC8665] |
       +-------------------+--------------------------+-----------+
       | Adjacency SID     | Adj-SID Sub-TLV (5)      | [RFC8666] |
       +-------------------+--------------------------+-----------+
       | LAN Adjacency SID | LAN Adj-SID Sub-TLV (6)  | [RFC8666] |
       +-------------------+--------------------------+-----------+
       | Prefix-SID        | Prefix-SID Sub-TLV (4)   | [RFC8666] |
       +-------------------+--------------------------+-----------+
       | Range             | OSPFv3 Extended Prefix   | [RFC8666] |
       |                   | Range TLV (9)            |           |
       +-------------------+--------------------------+-----------+
       | SID/Label         | SID/Label Sub-TLV (7)    | [RFC8666] |
       +-------------------+--------------------------+-----------+
       | Prefix Attribute  | Prefix Option Fields of  | [RFC8362] |
       | Flags             | Prefix TLV types 3,5,6   |           |
       +-------------------+--------------------------+-----------+
       | Source OSPF       | Prefix Source Router     | [RFC9084] |
       | Router Identifier | Address Sub-TLV (28)     |           |
       +-------------------+--------------------------+-----------+
       | Source OSPF       | Prefix Source OSPF       | [RFC9084] |
       | Router-ID         | Router-ID Sub-TLV (27)   |           |
       +-------------------+--------------------------+-----------+

         Table 7: OSPFv3 Segment Routing Extensions TLVs/Sub-TLVs

3.  IANA Considerations

   IANA has registered the following code points in the "BGP-LS Node
   Descriptor, Link Descriptor, Prefix Descriptor, and Attribute TLVs"
   registry under the "Border Gateway Protocol - Link State (BGP-LS)
   Parameter" registry based on Table 8.  The column "IS-IS TLV/Sub-TLV"
   defined in the registry does not require any value and should be left
   empty.

3.1.  TLV/Sub-TLV Code Points Summary

   This section contains the global table of all TLVs/sub-TLVs defined
   in this document.

     +================+=============================+===============+
     | TLV Code Point | Description                 | Reference     |
     +================+=============================+===============+
     |      1034      | SR Capabilities             | Section 2.1.2 |
     +----------------+-----------------------------+---------------+
     |      1035      | SR Algorithm                | Section 2.1.3 |
     +----------------+-----------------------------+---------------+
     |      1036      | SR Local Block              | Section 2.1.4 |
     +----------------+-----------------------------+---------------+
     |      1037      | SRMS Preference             | Section 2.1.5 |
     +----------------+-----------------------------+---------------+
     |      1099      | Adjacency SID               | Section 2.2.1 |
     +----------------+-----------------------------+---------------+
     |      1100      | LAN Adjacency SID           | Section 2.2.2 |
     +----------------+-----------------------------+---------------+
     |      1158      | Prefix-SID                  | Section 2.3.1 |
     +----------------+-----------------------------+---------------+
     |      1159      | Range                       | Section 2.3.5 |
     +----------------+-----------------------------+---------------+
     |      1161      | SID/Label                   | Section 2.1.1 |
     +----------------+-----------------------------+---------------+
     |      1170      | Prefix Attribute Flags      | Section 2.3.2 |
     +----------------+-----------------------------+---------------+
     |      1171      | Source Router Identifier    | Section 2.3.3 |
     +----------------+-----------------------------+---------------+
     |      1172      | L2 Bundle Member Attributes | Section 2.2.3 |
     +----------------+-----------------------------+---------------+
     |      1174      | Source OSPF Router-ID       | Section 2.3.4 |
     +----------------+-----------------------------+---------------+

               Table 8: Summary of TLV/Sub-TLV Code Points

4.  Manageability Considerations

   This section is structured as recommended in [RFC5706].

   The new protocol extensions introduced in this document augment the
   existing IGP topology information that is distributed via [RFC7752].
   Procedures and protocol extensions defined in this document do not
   affect the BGP protocol operations and management other than as
   discussed in the Manageability Considerations section of [RFC7752].
   Specifically, the malformed attribute tests for syntactic checks in
   the Fault Management section of [RFC7752] now encompass the new BGP-
   LS Attribute TLVs defined in this document.  The semantic or content
   checking for the TLVs specified in this document and their
   association with the BGP-LS NLRI types or their BGP-LS Attribute is
   left to the consumer of the BGP-LS information (e.g., an application
   or a controller) and not the BGP protocol.

   A consumer of the BGP-LS information retrieves this information over
   a BGP-LS session (refer to Sections 1 and 2 of [RFC7752]).  The
   handling of semantic or content errors by the consumer would be
   dictated by the nature of its application usage and hence is beyond
   the scope of this document.

   This document only introduces new Attribute TLVs, and any syntactic
   error in them would result in the BGP-LS Attribute being discarded
   with an error log.  The SR information introduced in BGP-LS by this
   specification may be used by BGP-LS consumer applications like an SR
   Path Computation Engine (PCE) to learn the SR capabilities of the
   nodes in the topology and the mapping of SR segments to those nodes.
   This can enable the SR PCE to perform path computations based on SR
   for traffic engineering use cases and to steer traffic on paths
   different from the underlying IGP-based distributed best-path
   computation.  Errors in the encoding or decoding of the SR
   information may result in the unavailability of such information to
   the SR PCE or incorrect information being made available to it.  This
   may result in the SR PCE not being able to perform the desired SR-
   based optimization functionality or to perform it in an unexpected or
   inconsistent manner.  The handling of such errors by applications
   like SR PCE may be implementation specific and out of scope of this
   document.

   The extensions, specified in this document, do not introduce any new
   configuration or monitoring aspects in BGP or BGP-LS other than as
   discussed in [RFC7752].  The manageability aspects of the underlying
   SR features are covered by [RFC9020], [ISIS-SR-YANG], and
   [OSPF-SR-YANG].

5.  Security Considerations

   The new protocol extensions introduced in this document augment the
   existing IGP topology information that is distributed via [RFC7752].
   The advertisement of the SR link attribute information defined in
   this document presents similar risk as associated with the existing
   set of link attribute information as described in [RFC7752].  The
   Security Considerations section of [RFC7752] also applies to these
   extensions.  The procedures and new TLVs defined in this document, by
   themselves, do not affect the BGP-LS security model discussed in
   [RFC7752].

   The TLVs introduced in this document are used to propagate IGP-
   defined information (see [RFC8665], [RFC8666], and [RFC8667]).  These
   TLVs represent the SR information associated with the IGP node, link,
   and prefix.  The IGP instances originating these TLVs are assumed to
   support all the required security and authentication mechanisms (as
   described in [RFC8665], [RFC8666], and [RFC8667]) in order to prevent
   any security issue when propagating the TLVs into BGP-LS.

   BGP-LS SR extensions enable traffic engineering use cases within the
   SR domain.  SR operates within a trusted domain [RFC8402], and its
   security considerations also apply to BGP-LS sessions when carrying
   SR information.  The SR traffic engineering policies using the SIDs
   advertised via BGP-LS are expected to be used entirely within this
   trusted SR domain (e.g., between multiple ASes/domains within a
   single provider network).  Therefore, precaution is necessary to
   ensure that the link-state information (including SR information)
   advertised via BGP-LS sessions is limited to consumers in a secure
   manner within this trusted SR domain.  BGP peering sessions for
   address families other than link state may be set up to routers
   outside the SR domain.  The isolation of BGP-LS peering sessions is
   recommended to ensure that BGP-LS topology information (including the
   newly added SR information) is not advertised to an external BGP
   peering session outside the SR domain.

6.  References

6.1.  Normative References

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119,
              DOI 10.17487/RFC2119, March 1997,
              <https://www.rfc-editor.org/info/rfc2119>.

   [RFC4202]  Kompella, K., Ed. and Y. Rekhter, Ed., "Routing Extensions
              in Support of Generalized Multi-Protocol Label Switching
              (GMPLS)", RFC 4202, DOI 10.17487/RFC4202, October 2005,
              <https://www.rfc-editor.org/info/rfc4202>.

   [RFC5120]  Przygienda, T., Shen, N., and N. Sheth, "M-ISIS: Multi
              Topology (MT) Routing in Intermediate System to
              Intermediate Systems (IS-ISs)", RFC 5120,
              DOI 10.17487/RFC5120, February 2008,
              <https://www.rfc-editor.org/info/rfc5120>.

   [RFC5308]  Hopps, C., "Routing IPv6 with IS-IS", RFC 5308,
              DOI 10.17487/RFC5308, October 2008,
              <https://www.rfc-editor.org/info/rfc5308>.

   [RFC5340]  Coltun, R., Ferguson, D., Moy, J., and A. Lindem, "OSPF
              for IPv6", RFC 5340, DOI 10.17487/RFC5340, July 2008,
              <https://www.rfc-editor.org/info/rfc5340>.

   [RFC7684]  Psenak, P., Gredler, H., Shakir, R., Henderickx, W.,
              Tantsura, J., and A. Lindem, "OSPFv2 Prefix/Link Attribute
              Advertisement", RFC 7684, DOI 10.17487/RFC7684, November
              2015, <https://www.rfc-editor.org/info/rfc7684>.

   [RFC7752]  Gredler, H., Ed., Medved, J., Previdi, S., Farrel, A., and
              S. Ray, "North-Bound Distribution of Link-State and
              Traffic Engineering (TE) Information Using BGP", RFC 7752,
              DOI 10.17487/RFC7752, March 2016,
              <https://www.rfc-editor.org/info/rfc7752>.

   [RFC7794]  Ginsberg, L., Ed., Decraene, B., Previdi, S., Xu, X., and
              U. Chunduri, "IS-IS Prefix Attributes for Extended IPv4
              and IPv6 Reachability", RFC 7794, DOI 10.17487/RFC7794,
              March 2016, <https://www.rfc-editor.org/info/rfc7794>.

   [RFC8174]  Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
              2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
              May 2017, <https://www.rfc-editor.org/info/rfc8174>.

   [RFC8362]  Lindem, A., Roy, A., Goethals, D., Reddy Vallem, V., and
              F. Baker, "OSPFv3 Link State Advertisement (LSA)
              Extensibility", RFC 8362, DOI 10.17487/RFC8362, April
              2018, <https://www.rfc-editor.org/info/rfc8362>.

   [RFC8402]  Filsfils, C., Ed., Previdi, S., Ed., Ginsberg, L.,
              Decraene, B., Litkowski, S., and R. Shakir, "Segment
              Routing Architecture", RFC 8402, DOI 10.17487/RFC8402,
              July 2018, <https://www.rfc-editor.org/info/rfc8402>.

   [RFC8571]  Ginsberg, L., Ed., Previdi, S., Wu, Q., Tantsura, J., and
              C. Filsfils, "BGP - Link State (BGP-LS) Advertisement of
              IGP Traffic Engineering Performance Metric Extensions",
              RFC 8571, DOI 10.17487/RFC8571, March 2019,
              <https://www.rfc-editor.org/info/rfc8571>.

   [RFC8665]  Psenak, P., Ed., Previdi, S., Ed., Filsfils, C., Gredler,
              H., Shakir, R., Henderickx, W., and J. Tantsura, "OSPF
              Extensions for Segment Routing", RFC 8665,
              DOI 10.17487/RFC8665, December 2019,
              <https://www.rfc-editor.org/info/rfc8665>.

   [RFC8666]  Psenak, P., Ed. and S. Previdi, Ed., "OSPFv3 Extensions
              for Segment Routing", RFC 8666, DOI 10.17487/RFC8666,
              December 2019, <https://www.rfc-editor.org/info/rfc8666>.

   [RFC8667]  Previdi, S., Ed., Ginsberg, L., Ed., Filsfils, C.,
              Bashandy, A., Gredler, H., and B. Decraene, "IS-IS
              Extensions for Segment Routing", RFC 8667,
              DOI 10.17487/RFC8667, December 2019,
              <https://www.rfc-editor.org/info/rfc8667>.

   [RFC8668]  Ginsberg, L., Ed., Bashandy, A., Filsfils, C., Nanduri,
              M., and E. Aries, "Advertising Layer 2 Bundle Member Link
              Attributes in IS-IS", RFC 8668, DOI 10.17487/RFC8668,
              December 2019, <https://www.rfc-editor.org/info/rfc8668>.

   [RFC9084]  Wang, A., Lindem, A., Dong, J., Psenak, P., and K.
              Talaulikar, Ed., "OSPF Prefix Originator Extensions",
              RFC 9084, DOI 10.17487/RFC9084, August 2021,
              <https://www.rfc-editor.org/info/rfc9084>.

6.2.  Informative References

   [ISIS-SR-YANG]
              Litkowski, S., Qu, Y., Sarkar, P., Chen, I., and J.
              Tantsura, "YANG Data Model for IS-IS Segment Routing",
              Work in Progress, Internet-Draft, draft-ietf-isis-sr-yang-
              10, 21 February 2021,
              <https://datatracker.ietf.org/doc/html/draft-ietf-isis-sr-
              yang-10>.

   [OSPF-SR-YANG]
              Yeung, D., Qu, Y., Zhang, J., Chen, I., and A. Lindem,
              "YANG Data Model for OSPF SR (Segment Routing) Protocol",
              Work in Progress, Internet-Draft, draft-ietf-ospf-sr-yang-
              15, 2 July 2021, <https://datatracker.ietf.org/doc/html/
              draft-ietf-ospf-sr-yang-15>.

   [RFC5706]  Harrington, D., "Guidelines for Considering Operations and
              Management of New Protocols and Protocol Extensions",
              RFC 5706, DOI 10.17487/RFC5706, November 2009,
              <https://www.rfc-editor.org/info/rfc5706>.

   [RFC8661]  Bashandy, A., Ed., Filsfils, C., Ed., Previdi, S.,
              Decraene, B., and S. Litkowski, "Segment Routing MPLS
              Interworking with LDP", RFC 8661, DOI 10.17487/RFC8661,
              December 2019, <https://www.rfc-editor.org/info/rfc8661>.

   [RFC9020]  Litkowski, S., Qu, Y., Lindem, A., Sarkar, P., and J.
              Tantsura, "YANG Data Model for Segment Routing", RFC 9020,
              DOI 10.17487/RFC9020, May 2021,
              <https://www.rfc-editor.org/info/rfc9020>.

Acknowledgements

   The authors would like to thank Jeffrey Haas, Aijun Wang, Robert
   Raszuk, and Susan Hares for their review of this document and their
   comments.  The authors would also like to thank Alvaro Retana for his
   extensive review and comments, which helped correct issues and
   improve the document.

Contributors

   The following people have substantially contributed to the editing of
   this document:

   Peter Psenak
   Cisco Systems

   Email: ppsenak@cisco.com


   Les Ginsberg
   Cisco Systems

   Email: ginsberg@cisco.com


   Acee Lindem
   Cisco Systems

   Email: acee@cisco.com


   Saikat Ray
   Individual

   Email: raysaikat@gmail.com


   Jeff Tantsura
   Apstra Inc.

   Email: jefftant.ietf@gmail.com


Authors' Addresses

   Stefano Previdi
   Huawei Technologies
   Rome
   Italy

   Email: stefano@previdi.net


   Ketan Talaulikar (editor)
   Cisco Systems, Inc.
   India

   Email: ketant@cisco.com


   Clarence Filsfils
   Cisco Systems, Inc.
   Brussels
   Belgium

   Email: cfilsfil@cisco.com


   Hannes Gredler
   RtBrick Inc.

   Email: hannes@rtbrick.com


   Mach(Guoyi) Chen
   Huawei Technologies
   Huawei Building, No. 156 Beiqing Rd.
   Beijing
   100095
   China