Rfc8538
TitleNotification Message Support for BGP Graceful Restart
AuthorK. Patel, R. Fernando, J. Scudder, J. Haas
DateMarch 2019
Format:TXT, HTML
UpdatesRFC4724
Status:PROPOSED STANDARD






Internet Engineering Task Force (IETF)                          K. Patel
Request for Comments: 8538                                        Arrcus
Updates: 4724                                                R. Fernando
Category: Standards Track                                  Cisco Systems
ISSN: 2070-1721                                               J. Scudder
                                                                 J. Haas
                                                        Juniper Networks
                                                              March 2019


         Notification Message Support for BGP Graceful Restart

Abstract

   The BGP Graceful Restart mechanism defined in RFC 4724 limits the
   usage of BGP Graceful Restart to BGP messages other than BGP
   NOTIFICATION messages.  This document updates RFC 4724 by defining an
   extension that permits the Graceful Restart procedures to be
   performed when the BGP speaker receives a BGP NOTIFICATION message or
   the Hold Time expires.  This document also defines a new subcode for
   BGP Cease NOTIFICATION messages; this new subcode requests a full
   session restart instead of a Graceful Restart.

Status of This Memo

   This is an Internet Standards Track document.

   This document is a product of the Internet Engineering Task Force
   (IETF).  It represents the consensus of the IETF community.  It has
   received public review and has been approved for publication by the
   Internet Engineering Steering Group (IESG).  Further information on
   Internet Standards is available in Section 2 of RFC 7841.

   Information about the current status of this document, any errata,
   and how to provide feedback on it may be obtained at
   https://www.rfc-editor.org/info/rfc8538.















RFC 8538             Notification Support for BGP GR          March 2019


Copyright Notice

   Copyright (c) 2019 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (https://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   3
     1.1.  Requirements Language . . . . . . . . . . . . . . . . . .   3
   2.  Modifications to BGP Graceful Restart Capability  . . . . . .   3
   3.  BGP Hard Reset Subcode  . . . . . . . . . . . . . . . . . . .   4
     3.1.  Sending a Hard Reset  . . . . . . . . . . . . . . . . . .   4
     3.2.  Receiving a Hard Reset  . . . . . . . . . . . . . . . . .   4
   4.  Operation . . . . . . . . . . . . . . . . . . . . . . . . . .   5
     4.1.  Rules for the Receiving Speaker . . . . . . . . . . . . .   6
   5.  Use of Hard Reset . . . . . . . . . . . . . . . . . . . . . .   7
     5.1.  When to Send a Hard Reset . . . . . . . . . . . . . . . .   7
     5.2.  Interaction with Other Specifications . . . . . . . . . .   7
   6.  Management Considerations . . . . . . . . . . . . . . . . . .   8
   7.  Operational Considerations  . . . . . . . . . . . . . . . . .   8
   8.  IANA Considerations . . . . . . . . . . . . . . . . . . . . .   8
   9.  Security Considerations . . . . . . . . . . . . . . . . . . .   9
   10. References  . . . . . . . . . . . . . . . . . . . . . . . . .   9
     10.1.  Normative References . . . . . . . . . . . . . . . . . .   9
     10.2.  Informative References . . . . . . . . . . . . . . . . .   9
   Acknowledgements  . . . . . . . . . . . . . . . . . . . . . . . .  10
   Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . . .  10














RFC 8538             Notification Support for BGP GR          March 2019


1.  Introduction

   For many classes of errors, BGP must send a NOTIFICATION message and
   reset the peering session to handle the error condition.  The BGP
   Graceful Restart mechanism defined in [RFC4724] requires that normal
   BGP procedures defined in [RFC4271] be followed when a NOTIFICATION
   message is sent or received.  This document defines an extension to
   BGP Graceful Restart that permits the Graceful Restart procedures to
   be performed when the BGP speaker receives a NOTIFICATION message or
   the Hold Time expires.  This permits the BGP speaker to avoid
   flapping reachability and continue forwarding while the BGP speaker
   restarts the session to handle errors detected in BGP.

   At a high level, this document can be summed up as follows.  When a
   BGP session is reset, both speakers operate as "Receiving Speakers"
   according to [RFC4724], meaning they retain each other's routes.
   This is also true for HOLDTIME expiration.  The functionality can be
   defeated by sending a BGP Cease NOTIFICATION message with the Hard
   Reset subcode.  If a Hard Reset is used, a full session reset is
   performed.

1.1.  Requirements Language

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
   "OPTIONAL" in this document are to be interpreted as described in
   BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all
   capitals, as shown here.

2.  Modifications to BGP Graceful Restart Capability

   The BGP Graceful Restart Capability is augmented to signal the
   Graceful Restart support for BGP NOTIFICATION messages.  The Restart
   Flags field is augmented as follows (following the diagram in
   Section 3 of [RFC4724]).

   Restart Flags:

         This field contains bit flags relating to restart.

                0 1 2 3
               +-+-+-+-+
               |R|N|   |
               +-+-+-+-+

   The most significant bit is defined in [RFC4724] as the Restart State
   ("R") bit.




RFC 8538             Notification Support for BGP GR          March 2019


   The second most significant bit is defined in this document as the
   Graceful Notification ("N") bit.  It is used to indicate Graceful
   Restart support for BGP NOTIFICATION messages.  A BGP speaker
   indicates support for the procedures in this document by advertising
   a Graceful Restart Capability with its "N" bit set (value 1).

   If a BGP speaker that previously advertised a given set of Graceful
   Restart parameters opens a new session with a different set of
   parameters, these new parameters apply once the session has
   transitioned into ESTABLISHED state.

3.  BGP Hard Reset Subcode

   This document defines a new subcode for BGP Cease NOTIFICATION
   messages, called the Hard Reset subcode.  The value of this subcode
   is discussed in Section 8.  In this document, a BGP Cease
   NOTIFICATION message with the Hard Reset subcode is referred to as a
   "Hard Reset message" or simply as a "Hard Reset".

   When the "N" bit has been exchanged by two peers, NOTIFICATION
   messages other than Hard Reset messages are referred to as
   "Graceful", since such messages invoke Graceful Restart semantics.

3.1.  Sending a Hard Reset

   When the "N" bit has been exchanged, a Hard Reset message is used to
   indicate to the peer that the session is to be fully terminated.

   When sending a Hard Reset, the data portion of the NOTIFICATION
   message is encoded as follows:

       +--------+--------+--------
       | ErrCode| Subcode| Data
       +--------+--------+--------

   ErrCode is a BGP Error Code (as documented in the IANA "BGP Error
   (Notification) Codes" registry) that indicates the reason for the
   Hard Reset.  Subcode is a BGP Error Subcode (as documented in the
   IANA "BGP Error Subcodes" registry) as appropriate for the ErrCode.
   Similarly, Data is as appropriate for the ErrCode and Subcode.  In
   short, the Hard Reset encapsulates another NOTIFICATION message in
   its data portion.

3.2.  Receiving a Hard Reset

   Whenever a BGP speaker receives a Hard Reset, the speaker MUST
   terminate the BGP session following the standard procedures in
   [RFC4271].



RFC 8538             Notification Support for BGP GR          March 2019


4.  Operation

   A BGP speaker that is willing to receive and send BGP NOTIFICATION
   messages according to the procedures of this document MUST advertise
   the "N" bit using the Graceful Restart Capability as defined in
   [RFC4724].

   When such a BGP speaker has received the "N" bit from its peer, and
   receives from that peer a BGP NOTIFICATION message other than a Hard
   Reset, it MUST follow the rules for the Receiving Speaker mentioned
   in Section 4.1.  The BGP speaker generating the BGP NOTIFICATION
   message MUST also follow the rules for the Receiving Speaker.

   When a BGP speaker resets its session due to a HOLDTIME expiry, it
   should generate the relevant BGP NOTIFICATION message as mentioned in
   [RFC4271] but subsequently MUST follow the rules for the Receiving
   Speaker mentioned in Section 4.1.

   A BGP speaker SHOULD NOT send a Hard Reset to a peer from which it
   has not received the "N" bit.  We note, however, that if it did so,
   the effect would be as desired in any case because, according to
   [RFC4271] and [RFC4724], any NOTIFICATION message, whether recognized
   or not, results in a session reset.  Thus, the only negative effect
   to be expected from sending the Hard Reset to a peer that hasn't
   advertised compliance to this specification would be that the peer
   would be unable to properly log the associated information.

   Once the session is re-established, both BGP speakers SHOULD set
   their Forwarding State bit to 1.  If the Forwarding State bit is not
   set, then, according to the procedures in Section 4.2 of [RFC4724],
   the relevant routes will be flushed, defeating the goals of this
   specification.



















RFC 8538             Notification Support for BGP GR          March 2019


4.1.  Rules for the Receiving Speaker

   Section 4.2 of [RFC4724] defines rules for the Receiving Speaker.
   This document modifies those rules as follows:

   The sentence "To deal with possible consecutive restarts, a route
   (from the peer) previously marked as stale MUST be deleted" only
   applies when the "N" bit has not been exchanged with the peer:

   OLD: When the Receiving Speaker detects termination of the TCP
        session for a BGP session with a peer that has advertised the
        Graceful Restart Capability, it MUST retain the routes received
        from the peer for all the address families that were previously
        received in the Graceful Restart Capability and MUST mark them
        as stale routing information.  To deal with possible consecutive
        restarts, a route (from the peer) previously marked as stale
        MUST be deleted.  The router MUST NOT differentiate between
        stale and other routing information during forwarding.

   NEW: When the Receiving Speaker detects termination of the TCP
        session for a BGP session with a peer that has advertised the
        Graceful Restart Capability, it MUST retain the routes received
        from the peer for all the address families that were previously
        received in the Graceful Restart Capability and MUST mark them
        as stale routing information.  The router MUST NOT differentiate
        between stale and other routing information during forwarding.
        If the "N" bit has not been exchanged with the peer, then to
        deal with possible consecutive restarts, a route (from the peer)
        previously marked as stale MUST be deleted.

   The stale timer is given a formal name and made mandatory:

   OLD: To put an upper bound on the amount of time a router retains the
        stale routes, an implementation MAY support a (configurable)
        timer that imposes this upper bound.

   NEW: To put an upper bound on the amount of time a router retains the
        stale routes, an implementation MUST support a (configurable)
        timer, called the "stale timer", that imposes this upper bound.
        A suggested default value for the stale timer is 180 seconds.
        An implementation MAY provide the option to disable the timer
        (i.e., to provide an infinite retention time) but MUST NOT do so
        by default.








RFC 8538             Notification Support for BGP GR          March 2019


5.  Use of Hard Reset

5.1.  When to Send a Hard Reset

   Although when to send a Hard Reset is an implementation-specific
   decision, we offer some advice.  Many Cease NOTIFICATION subcodes
   represent permanent or long-term, rather than transient, session
   termination.  Because of this, it's appropriate to use Hard Reset
   with them.  As of publication of this document, subcodes 1-9 have
   been defined for Cease.  The following table lists each of these
   subcodes along with suggested behavior.

   +-------+------------------------------------+----------------------+
   | Value |                Name                |  Suggested Behavior  |
   +-------+------------------------------------+----------------------+
   |   1   | Maximum Number of Prefixes Reached |      Hard Reset      |
   |   2   |      Administrative Shutdown       |      Hard Reset      |
   |   3   |         Peer De-configured         |      Hard Reset      |
   |   4   |        Administrative Reset        | Provide user control |
   |   5   |        Connection Rejected         |    Graceful Cease    |
   |   6   |     Other Configuration Change     |    Graceful Cease    |
   |   7   |  Connection Collision Resolution   |    Graceful Cease    |
   |   8   |          Out of Resources          |    Graceful Cease    |
   |   9   |             Hard Reset             |      Hard Reset      |
   +-------+------------------------------------+----------------------+

   These suggestions are only that -- suggestions, not requirements.
   It's the nature of BGP implementations that the mapping of internal
   states to BGP NOTIFICATION codes and subcodes is not always perfect.
   The guiding principle for the implementor should be that if there is
   no realistic hope that forwarding can continue or that the session
   will be re-established within the deadline, Hard Reset should be
   used.

   For all NOTIFICATION codes other than Cease, use of Hard Reset does
   not appear to be indicated.

5.2.  Interaction with Other Specifications

   "BGP Administrative Shutdown Communication" [RFC8203] specifies use
   of the data portion of the Administrative Shutdown or Administrative
   Reset subcodes to convey a short message.  When [RFC8203] is used in
   conjunction with Hard Reset, the subcode of the outermost Cease MUST
   be Hard Reset, with the Administrative Shutdown or Administrative
   Reset subcodes encapsulated within.  The encapsulated message MUST
   subsequently be processed according to [RFC8203].





RFC 8538             Notification Support for BGP GR          March 2019


6.  Management Considerations

   When reporting a Hard Reset to network management, the error code and
   subcode reported MUST be Cease and Hard Reset, respectively.  If the
   network management layer in use permits it, the information carried
   in the Data portion SHOULD be reported as well.

7.  Operational Considerations

   Note that long (or infinite) retention time may cause operational
   issues and should be enabled with care.

8.  IANA Considerations

   IANA has assigned subcode 9 ("Hard Reset") in the "BGP Cease
   NOTIFICATION message subcodes" registry.

   IANA has created a sub-registry called "BGP Graceful Restart Flags"
   under the "Border Gateway Protocol (BGP) Parameters" registry.  The
   registration procedure is Standards Action [RFC8126]; this document
   and [RFC4724] are listed as references.  The initial values are as
   follows:

         +--------------+---------------+------------+-----------+
         | Bit Position |      Name     | Short Name | Reference |
         +--------------+---------------+------------+-----------+
         |      0       | Restart State |     R      |  RFC 4724 |
         |      1       |  Notification |     N      |  RFC 8538 |
         |     2-3      |   Unassigned  |            |           |
         +--------------+---------------+------------+-----------+

   IANA has created a sub-registry called "BGP Graceful Restart Flags
   for Address Family" under the "Border Gateway Protocol (BGP)
   Parameters" registry.  The registration procedure is Standards
   Action; this document and [RFC4724] are listed as references.  The
   initial values are as follows:

       +--------------+------------------+------------+-----------+
       | Bit Position |       Name       | Short Name | Reference |
       +--------------+------------------+------------+-----------+
       |      0       | Forwarding State |     F      |  RFC 4724 |
       |     1-7      |    Unassigned    |            |           |
       +--------------+------------------+------------+-----------+








RFC 8538             Notification Support for BGP GR          March 2019


9.  Security Considerations

   This specification doesn't change the basic security model inherent
   in [RFC4724], with the exception that the protection against repeated
   resets is relaxed.  To mitigate the consequent risk that an attacker
   could use repeated session resets to prevent stale routes from ever
   being deleted, we make the stale timer mandatory (in practice, it is
   already ubiquitous).  To the extent [RFC4724] might be said to help
   defend against denials of service by making the control plane more
   resilient, this extension may modestly increase that resilience;
   however, there are enough confounding and deployment-specific factors
   that no general claims can be made.

10.  References

10.1.  Normative References

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119,
              DOI 10.17487/RFC2119, March 1997,
              <https://www.rfc-editor.org/info/rfc2119>.

   [RFC4271]  Rekhter, Y., Ed., Li, T., Ed., and S. Hares, Ed., "A
              Border Gateway Protocol 4 (BGP-4)", RFC 4271,
              DOI 10.17487/RFC4271, January 2006,
              <https://www.rfc-editor.org/info/rfc4271>.

   [RFC4724]  Sangli, S., Chen, E., Fernando, R., Scudder, J., and Y.
              Rekhter, "Graceful Restart Mechanism for BGP", RFC 4724,
              DOI 10.17487/RFC4724, January 2007,
              <https://www.rfc-editor.org/info/rfc4724>.

   [RFC8174]  Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
              2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
              May 2017, <https://www.rfc-editor.org/info/rfc8174>.

   [RFC8203]  Snijders, J., Heitz, J., and J. Scudder, "BGP
              Administrative Shutdown Communication", RFC 8203,
              DOI 10.17487/RFC8203, July 2017,
              <https://www.rfc-editor.org/info/rfc8203>.

10.2.  Informative References

   [RFC8126]  Cotton, M., Leiba, B., and T. Narten, "Guidelines for
              Writing an IANA Considerations Section in RFCs", BCP 26,
              RFC 8126, DOI 10.17487/RFC8126, June 2017,
              <https://www.rfc-editor.org/info/rfc8126>.




RFC 8538             Notification Support for BGP GR          March 2019


Acknowledgements

   The authors would like to thank Jim Uttaro for the suggestion.  The
   authors would also like to thank Emmanuel Baccelli, Bruno Decraene,
   Chris Hall, Warren Kumari, Paul Mattes, Robert Raszuk, and Alvaro
   Retana for their reviews and comments.

Authors' Addresses

   Keyur Patel
   Arrcus

   Email: keyur@arrcus.com


   Rex Fernando
   Cisco Systems
   170 W. Tasman Drive
   San Jose, CA  95134
   United States of America

   Email: rex@cisco.com


   John Scudder
   Juniper Networks
   1194 N. Mathilda Ave
   Sunnyvale, CA  94089
   United States of America

   Email: jgs@juniper.net


   Jeff Haas
   Juniper Networks
   1194 N. Mathilda Ave
   Sunnyvale, CA  94089
   United States of America

   Email: jhaas@juniper.net