Rfc5561
TitleLDP Capabilities
AuthorB. Thomas, K. Raza, S. Aggarwal, R. Aggarwal, JL. Le Roux
DateJuly 2009
Format:TXT, HTML
Status:PROPOSED STANDARD






Network Working Group                                          B. Thomas
Request for Comments: 5561                                       K. Raza
Updates: 5036                                        Cisco Systems, Inc.
Category: Standards Track                                    S. Aggarwal
                                                             R. Aggarwal
                                                        Juniper Networks
                                                             JL. Le Roux
                                                          France Telecom
                                                               July 2009


                           LDP Capabilities

Abstract

   A number of enhancements to the Label Distribution Protocol (LDP)
   have been proposed.  Some have been implemented, and some are
   advancing toward standardization.  It is likely that additional
   enhancements will be proposed in the future.  This document defines a
   mechanism for advertising LDP enhancements at session initialization
   time, as well as a mechanism to enable and disable enhancements after
   LDP session establishment.

Status of This Memo

   This document specifies an Internet standards track protocol for the
   Internet community, and requests discussion and suggestions for
   improvements.  Please refer to the current edition of the "Internet
   Official Protocol Standards" (STD 1) for the standardization state
   and status of this protocol.  Distribution of this memo is unlimited.

Copyright Notice

   Copyright (c) 2009 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents in effect on the date of
   publication of this document (http://trustee.ietf.org/license-info).
   Please review these documents carefully, as they describe your rights
   and restrictions with respect to this document.

   This document may contain material from IETF Documents or IETF
   Contributions published or made publicly available before November
   10, 2008.  The person(s) controlling the copyright in some of this
   material may not have granted the IETF Trust the right to allow
   modifications of such material outside the IETF Standards Process.
   Without obtaining an adequate license from the person(s) controlling



RFC 5561                    LDP Capabilities                   July 2009


   the copyright in such materials, this document may not be modified
   outside the IETF Standards Process, and derivative works of it may
   not be created outside the IETF Standards Process, except to format
   it for publication as an RFC or to translate it into languages other
   than English.

Table of Contents

   1. Introduction ....................................................2
      1.1. Conventions Used in This Document ..........................3
   2. The LDP Capability Mechanism ....................................3
      2.1. Capability Document ........................................4
   3. Specifying Capabilities in LDP Messages .........................4
      3.1. Backward Compatibility TLVs ................................6
   4. Capability Message ..............................................6
   5. Note on Terminology .............................................7
   6. Procedures for Capability Parameters in Initialization
      Messages ........................................................7
   7. Procedures for Capability Parameters in Capability Messages .....8
   8. Extensions to Error Handling ....................................9
   9. Dynamic Capability Announcement TLV .............................9
   10. Backward Compatibility ........................................10
   11. Security Considerations .......................................10
   12. IANA Considerations ...........................................11
   13. Acknowledgments ...............................................11
   14. References ....................................................11
      14.1. Normative References .....................................11
      14.2. Informative References ...................................11

1.  Introduction

   A number of enhancements to LDP as specified in [RFC5036] have been
   proposed.  These include LDP Graceful Restart [RFC3478], Fault
   Tolerant LDP [RFC3479], multicast extensions [MLDP], signaling for
   Layer 2 circuits [RFC4447], a method for learning labels advertised
   by next-next-hop routers in support of fast reroute node protection
   [NNHOP], upstream label allocation [UPSTREAM_LDP], and extensions for
   signaling inter-area Label Switched Paths (LSPs) [RFC5283].  Some
   have been implemented, and some are advancing toward standardization.
   It is also likely that additional enhancements will be implemented
   and deployed in the future.

   This document proposes and defines a mechanism for advertising LDP
   enhancements at session initialization time.  It also defines a
   mechanism to enable and disable these enhancements after LDP session
   establishment.





RFC 5561                    LDP Capabilities                   July 2009


   LDP capability advertisement provides means for an LDP speaker to
   announce what it can receive and process.  It also provides means for
   a speaker to inform peers of deviations from behavior specified by
   [RFC5036].  An example of such a deviation is LDP Graceful Restart,
   where a speaker retains MPLS forwarding state for LDP-signaled LSPs
   when its LDP control plane goes down.  It is important to point out
   that not all LDP enhancements require capability advertisement.  For
   example, upstream label allocation requires capability advertisement,
   but inbound label filtering, where a speaker installs forwarding
   state for only certain Forwarding Equivalence Classes (FECs), does
   not.

1.1.  Conventions Used in This Document

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in [RFC2119].

   This document uses the terms "LDP speaker" and "speaker"
   interchangeably.

2.  The LDP Capability Mechanism

   Enhancements are likely to be announced during LDP session
   establishment as each LDP speaker advertises capabilities
   corresponding to the enhancements it desires.

   Beyond that, capability advertisements may be used to dynamically
   modify the characteristics of the session to suit the changing
   conditions.  For example, an LSR capable of a particular enhancement
   in support of some "feature" may not have advertised the
   corresponding capability to its peers at session establishment time
   because the feature was disabled at that time.  Later, an operator
   may enable the feature, at which time the LSR would react by
   advertising the corresponding capability to its peers.  Similarly,
   when an operator disables a feature associated with a capability, the
   LSR reacts by withdrawing the capability advertisement from its
   peers.

   The LDP capability advertisement mechanism operates as follows:

   - Each LDP speaker is assumed to implement a set of enhancements,
     each of which has an associated capability.  At any time, a speaker
     may have none, one, or more of those enhancements "enabled".  When
     an enhancement is enabled, the speaker advertises the associated
     capability to its peers.  By advertising the capability to a peer,
     the speaker asserts that it shall perform the protocol actions
     specified for the associated enhancement.  For example, the actions



RFC 5561                    LDP Capabilities                   July 2009


     may require the LDP speaker to receive and process enhancement-
     specific messages from its peer.  Unless the capability has been
     advertised, the speaker will not perform protocol actions specified
     for the corresponding enhancement.

   - At session establishment time, an LDP speaker MAY advertise a
     particular capability by including an optional parameter associated
     with the capability in its Initialization message.

   - There is a well-known capability called Dynamic Capability
     Announcement that an LDP speaker MAY advertise in its
     Initialization message to indicate that it is capable of processing
     capability announcements following a session establishment.

     If a peer had advertised the Dynamic Capability Announcement
     capability in its Initialization message, then at any time
     following session establishment, an LDP speaker MAY announce
     changes in its advertised capabilities to that peer.  To do this,
     the LDP speaker sends the peer a Capability message that specifies
     the capabilities being advertised or withdrawn.

2.1.  Capability Document

   When the capability advertisement mechanism is in place, an LDP
   enhancement requiring LDP capability advertisement will be specified
   by a document that:

      - Describes the motivation for the enhancement;

      - Specifies the behavior of LDP when the enhancement is enabled.
        This includes the procedures, parameters, messages, and TLVs
        required by the enhancement;

      - Includes an IANA considerations section that requests IANA
        assignment of a code point (from TLV Type namespace) for the
        optional capability parameter corresponding to the enhancement.

        The capability document MUST also describe the interpretation
        and processing of associated capability data, if present.

3.  Specifying Capabilities in LDP Messages

   This document uses the term "Capability Parameter" to refer to an
   optional parameter that may be included in Initialization and
   Capability messages to advertise a capability.






RFC 5561                    LDP Capabilities                   July 2009


   The format of a "Capability Parameter" TLV is as follows:

      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |U|F| TLV Code Point            |            Length             |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |S| Reserved    |                                               |
      +-+-+-+-+-+-+-+-+       Capability Data                         |
      |                                               +-+-+-+-+-+-+-+-+
      |                                               |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   where:

      U-bit:
        Unknown TLV bit, as described in [RFC5036].  The value could be
        either 0 or 1 as specified in the Capability document associated
        with the given capability.

      F-bit:
        Forward unknown TLV bit, as described in [RFC5036].  The value
        of this bit MUST be 0 since a Capability Parameter TLV is sent
        only in Initialization and Capability messages, which are not
        forwarded.

      TLV Code Point:
        The TLV type that identifies a specific capability.  This is an
        IANA-assigned code point (from TLV Type namespace) for a given
        capability as requested in the associated capability document.

      S-bit:
        The State Bit.  It indicates whether the sender is advertising
        or withdrawing the capability corresponding to the TLV code
        point.  The State Bit value is used as follows:

          1 - The TLV is advertising the capability specified by the TLV
              code point.

          0 - The TLV is withdrawing the capability specified by the TLV
              code point.

      Capability Data:
        Information, if any, about the capability in addition to the TLV
        code point required to fully specify the capability.






RFC 5561                    LDP Capabilities                   July 2009


        The method for interpreting and processing this data is specific
        to the TLV code point and MUST be described in the document
        specifying the capability.

   An LDP speaker MUST NOT include more than one instance of a
   Capability Parameter (as identified by the same TLV code point) in an
   Initialization or Capability message.  If an LDP speaker receives
   more than one instance of the same Capability Parameter type in a
   message, it SHOULD send a Notification message to the peer before
   terminating the session with the peer.  The Status Code in the Status
   TLV of the Notification message MUST be Malformed TLV value, and the
   message SHOULD contain the second Capability Parameter TLV of the
   same type (code point) that is received in the message.

3.1.  Backward Compatibility TLVs

   LDP extensions that require advertisement or negotiation of some
   capability at session establishment time typically use TLVs that are
   included in an Initialization message.  To ensure backward
   compatibility with existing implementations, such TLVs continue to be
   supported in an Initialization message and are known in this document
   as "Backward Compatibility TLVs".  A Backward Compatibility TLV plays
   the role of a "Capability Parameter" TLV; that is, the presence of a
   Backward Compatibility TLV has the same meaning as a Capability
   Parameter TLV with the S-bit set for the same capability.

   One example of a Backward Capability TLV is the "FT Session TLV" that
   is exchanged in an Initialization message between peers to announce
   LDP Fault Tolerance [RFC3479] capability.

4.  Capability Message

   The LDP Capability message is used by an LDP speaker to announce
   changes in the state of one or more of its capabilities subsequent to
   session establishment.
















RFC 5561                    LDP Capabilities                   July 2009


   The format of the Capability message is as follows:

       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |0|    Capability (0x0202)      |            Length             |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                     Message ID                                |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                     TLV_1                                     |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                     . . .                                     |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                     TLV_N                                     |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   where TLV_1 through TLV_N are Capability Parameter TLVs.  The S-bit
   of each of the TLVs specifies the new state for the corresponding
   capability.

   Note that Backward Compatibility TLVs (see Section 3.1) MUST NOT be
   included in Capability messages.  An LDP speaker that receives a
   Capability message from a peer that includes Backward Compatibility
   TLVs SHOULD silently ignore these Backward Compatibility TLVs and
   continue processing the rest of the message.

5.  Note on Terminology

   The following sections in this document talk about enabling and
   disabling capabilities.  The terminology "enabling (or disabling) a
   capability" is short hand for "advertising (or withdrawing) a
   capability associated with an enhancement".  Bear in mind that it is
   an LDP enhancement that is being enabled or disabled, and that it is
   the corresponding capability that is being advertised or withdrawn.

6.  Procedures for Capability Parameters in Initialization Messages

   The S-bit of a Capability Parameter in an Initialization message MUST
   be 1 and SHOULD be ignored on receipt.  This ensures that any
   Capability Parameter in an Initialization message enables the
   corresponding capability.

   An LDP speaker determines the capabilities of a peer by examining the
   set of Capability Parameters present in the Initialization message
   received from the peer.

   An LDP speaker MAY use a particular capability with its peer after
   the speaker determines that the peer has enabled that capability.



RFC 5561                    LDP Capabilities                   July 2009


   These procedures enable an LDP speaker S1, that advertises a specific
   LDP capability C, to establish an LDP session with speaker S2 that
   does not advertise C.  In this situation, whether or not capability C
   may be used for the session depends on the semantics of the
   enhancement associated with C.  If the semantics do not require both
   S1 and S2, advertise C to one another, then S2 could use it; i.e.,
   S1's advertisement of C permits S2 to send messages to S1 used by the
   enhancement.

   It is the responsibility of the capability designer to specify the
   behavior of an LDP speaker that has enabled a certain enhancement,
   advertised its capability and determines that its peer has not
   advertised the corresponding capability.  The document specifying
   procedures for the capability MUST describe the behavior in this
   situation.  If the specified procedure is to terminate the session,
   then the LDP speaker SHOULD send a Notification message to the peer
   before terminating the session.  The Status Code in the Status TLV of
   the Notification message MUST be Unsupported Capability, and the
   message SHOULD contain the unsupported capability (see Section 8 for
   more details).

   An LDP speaker that supports capability advertisement and includes a
   Capability Parameter in its Initialization message MUST set the TLV
   U-bit to 0 or 1, as specified by Capability document.  The LDP
   speaker should set the U-bit to 1 if the capability document allows
   it to continue with a peer that does not understand the enhancement,
   and set the U-bit to 0 otherwise.  If a speaker receives a message
   containing unsupported capability, it responds according to the U-bit
   setting in the TLV.  If the U-bit is 1, then the speaker MUST
   silently ignore the Capability Parameter and allow the session to be
   established.  However, if the U-bit is 0, then speaker SHOULD send a
   Notification message to the peer before terminating the session.  The
   Status Code in the Status TLV of the Notification message MUST be
   Unsupported Capability, and the message SHOULD contain the
   unsupported capability (see Section 8 for more details).

7.  Procedures for Capability Parameters in Capability Messages

   An LDP speaker MUST NOT send a Capability message to a peer unless
   its peer advertised the Dynamic Capability Announcement capability in
   its session Initialization message.  An LDP speaker MAY send a
   Capability message to a peer if its peer advertised the Dynamic
   Capability Announcement capability in its session Initialization
   message (see Section 9).







RFC 5561                    LDP Capabilities                   July 2009


   An LDP speaker determines the capabilities enabled by a peer by
   determining the set of capabilities enabled at session initialization
   (as specified in Section 6) and tracking changes to that set made by
   Capability messages from the peer.

   An LDP speaker that has enabled a particular capability MAY use the
   enhancement corresponding to the capability with a peer after the
   speaker determines that the peer has enabled the capability.

8.  Extensions to Error Handling

   This document defines a new LDP status code named Unsupported
   Capability.  The E-bit of the Status TLV carried in a Notification
   message that includes this status code MUST be set to 0.

   In addition, this document defines a new LDP TLV, named Returned
   TLVs, that MAY be carried in a Notification message as an Optional
   Parameter.  The U-bit setting for a Returned TLVs TLV in a
   Notification message SHOULD be 1, and the F-bit setting SHOULD be 0.

   When the Status Code in a Notification message is Unsupported
   Capability, the message SHOULD specify the capabilities that are
   unsupported.  When the Notification message specifies the unsupported
   capabilities, it MUST include a Returned TLVs TLV.  The Returned TLVs
   TLV MUST include only the Capability Parameters for unsupported
   capabilities, and the Capability Parameter for each such capability
   SHOULD be encoded as received from the peer.

   When the Status Code in a Notification Message is Unknown TLV, the
   message SHOULD specify the TLV that was unknown.  When the
   Notification message specifies the TLV that was unknown, it MUST
   include the unknown TLV in a Returned TLVs TLV.

9.  Dynamic Capability Announcement TLV

   The Dynamic Capability Announcement TLV is a Capability Parameter
   defined by this document with following format:

       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |1|0| DynCap Ann. (0x0506)      |            Length (1)         |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |1| Reserved    |
      +-+-+-+-+-+-+-+-+






RFC 5561                    LDP Capabilities                   July 2009


   The value of the U-bit for the Dynamic Capability Announcement
   Parameter TLV MUST be set to 1 so that a receiver MUST silently
   ignore this TLV if unknown to it, and continue processing the rest of
   the message.  There is no "Capability Data" associated with this TLV
   and hence the TLV length MUST be set to 1.

   The Dynamic Capability Announcement Parameter MAY be included by an
   LDP speaker in an Initialization message to signal its peer that the
   speaker is capable of processing Capability messages.

   An LDP speaker MUST NOT include the Dynamic Capability Announcement
   Parameter in Capability messages sent to its peers.  Once enabled
   during session initialization, the Dynamic Capability Announcement
   capability cannot be disabled.  This implies that the S-bit is always
   1 for the Dynamic Capability Announcement.

   An LDP speaker that receives a Capability message from a peer that
   includes the Dynamic Capability Announcement Parameter SHOULD
   silently ignore the parameter and process any other Capability
   Parameters in the message.

10.  Backward Compatibility

   From the point of view of the LDP capability advertisement mechanism,
   an [RFC5036]-compliant peer has label distribution for IPv4 enabled
   by default.  To ensure compatibility with an [RFC5036]-compliant
   peer, LDP implementations that support capability advertisement have
   label distribution for IPv4 enabled until it is explicitly disabled
   and MUST assume that their peers do as well.

   Section 3.1 introduces the concept of Backward Compatibility TLVs
   that may appear in an Initialization message in the role of a
   Capability Parameter.  This permits existing LDP enhancements that
   use an ad hoc mechanism for enabling capabilities at session
   initialization time to continue to do so.

11.  Security Considerations

   [MPLS_SEC] describes the security framework for MPLS networks,
   whereas [RFC5036] describes the security considerations that apply to
   the base LDP specification.  The same security framework and
   considerations apply to the capability mechanism described in this
   document.








RFC 5561                    LDP Capabilities                   July 2009


12.  IANA Considerations

   This document specifies the following code points assigned by IANA:

      - LDP message code point for the Capability message (0x0202).

      - LDP TLV code point for the Dynamic Capability Announcement TLV
        (0x0506).

      - LDP TLV code point for the Returned TLVs TLV (0x0304).

      - LDP Status Code code point for the Unsupported Capability Status
        Code (0x0000002E).

13.  Acknowledgments

   The authors wish to thank Enke Chen, Vanson Lim, Ina Minei, Bin Mo,
   Yakov Rekhter, and Eric Rosen for their comments.

14.  References

14.1.  Normative References

   [RFC5036]      Andersson, L., Ed., Minei, I., Ed., and B. Thomas,
                  Ed., "LDP Specification", RFC 5036, October 2007.

   [RFC2119]      Bradner, S., "Key words for use in RFCs to Indicate
                  Requirement Levels", BCP 14, RFC 2119, March 1997.

   [RFC3479]      Farrel, A., Ed., "Fault Tolerance for the Label
                  Distribution Protocol (LDP)", RFC 3479, February 2003.

14.2.  Informative References

   [RFC5283]      Decraene, B., Le Roux, JL., and I. Minei, "LDP
                  Extension for Inter-Area Label Switched Paths (LSPs)",
                  RFC 5283, July 2008.

   [MLDP]         Minei, I., Ed., Kompella, K., Wijnands, I., Ed., and
                  B. Thomas, "Label Distribution Protocol Extensions for
                  Point-to-Multipoint and Multipoint-to-Multipoint Label
                  Switched Paths", Work in Progress, April 2009.

   [NNHOP]        Shen, N., Chen, E., and A. Tian, "Discovery LDP Next-
                  Nexthop Labels", Work in Progress, May 2005.






RFC 5561                    LDP Capabilities                   July 2009


   [RFC4447]      Martini, L., Ed., Rosen, E., El-Aawar, N., Smith, T.,
                  and G. Heron, "Pseudowire Setup and Maintenance Using
                  the Label Distribution Protocol (LDP)", RFC 4447,
                  April 2006.

   [RFC3478]      Leelanivas, M., Rekhter, Y., and R. Aggarwal,
                  "Graceful Restart Mechanism for Label Distribution
                  Protocol", RFC 3478, February 2003.

   [UPSTREAM_LDP] Aggarwal R., and J.L. Le Roux, "MPLS Upstream Label
                  Assignment for LDP" Work in Progress, July 2008.

   [MPLS_SEC]     Fang, L., Ed., "Security Framework for MPLS and GMPLS
                  Networks", Work in Progress, March 2009.

Authors' Addresses

   Bob Thomas
   Cisco Systems, Inc.
   1414 Massachusetts Ave.
   Boxborough, MA 01719
   EMail: bobthomas@alum.mit.edu

   Shivani Aggarwal
   Juniper Networks
   1194 North Mathilda Ave.
   Sunnyvale, CA 94089
   EMail: shivani@juniper.net

   Rahul Aggarwal
   Juniper Networks
   1194 North Mathilda Ave.
   Sunnyvale, CA 94089
   EMail: rahul@juniper.net

   Jean-Louis Le Roux
   France Telecom
   2, Avenue Pierre-Marzin
   22307 Lannion Cedex, France
   EMail: jeanlouis.leroux@orange-ftgroup.com

   Kamran Raza
   Cisco Systems, Inc.
   2000 Innovation Dr.
   Kanata, ON K2K 3E8, Canada
   EMail: skraza@cisco.com