Rfc2502
TitleLimitations of Internet Protocol Suite for Distributed Simulation the Large Multicast Environment
AuthorM. Pullen, M. Myjak, C. Bouwens
DateFebruary 1999
Format:TXT, HTML
Status:INFORMATIONAL






Network Working Group                                           M. Pullen
Request for Comments: 2502                        George Mason University
Category: Informational                                          M. Myjak
                                                     The Virtual Workshop
                                                               C. Bouwens
                                                                     SAIC
                                                            February 1999


   Limitations of Internet Protocol Suite for Distributed Simulation
                   in the Large Multicast Environment

Status of this Memo

   This memo provides information for the Internet community.  It does
   not specify an Internet standard of any kind.  Distribution of this
   memo is unlimited.

Copyright Notice

   Copyright (C) The Internet Society (1999).  All Rights Reserved.

Abstract

   The Large-Scale Multicast Applications (LSMA) working group was
   chartered to produce documents aimed at a consensus based development
   of the Internet protocols to support large scale multicast
   applications including real-time distributed simulation.  This memo
   defines services that LSMA has found to be required, and aspects of
   the Internet protocols that LSMA has found to need further
   development in order to meet these requirements.

1. The Large Multicast Environment

   The Large-Scale Multicast Applications working group (LSMA) was
   formed to create a consensus based requirement for Internet Protocols
   to support Distributed Interactive Simulation (DIS) [DIS94], its
   successor the High Level Architecture for simulation (HLA) [DMSO96],
   and related applications. The applications are characterized by the
   need to distribute a real-time applications over a shared wide area
   network in a scalable manner such that numbers of hosts from a few to
   tens of thousands are able to interchange state data with sufficient
   reliability and timeliness to sustain a three dimensional virtual,
   visual environment containing large numbers of moving objects.  The
   network supporting such an system necessarily will be capable of
   multicast [IEEE95a,IEEE95b].





RFC 2502         Limitations of Internet Protocol Suite    February 1999


   Distributed Interactive Simulation is the name of a family of
   protocols used to exchange information about a virtual environment
   among hosts in a distributed system that are simulating the behavior
   of objects in that environment.  The objects are capable of physical
   interactions and can sense each other by visual and other means
   (infrared, etc.).  DIS was developed by the U.S. Department of
   Defense (DoD) to implement systems for military training, rehearsal,
   and other purposes. More information on DIS can be found in [SSM96].

   The feature of distributed simulation that drives network
   requirements is that it is intended to work with output to and input
   from humans across distributed simulators in real time. This places
   tight limits on latency between hosts.  It also means that any
   practical network will require multicasting to implement the required
   distribution of all data to all participating simulators.  Large
   distributed simulation configurations are expected to group hosts on
   multicast groups based on sharing the same sensor inputs in the
   virtual environment.  This can mean a need for thousands of multicast
   groups where objects may move between groups in large numbers at high
   rates.  Because the number of simulators is known in advance and
   their maximum output rate in packets per second and bits per second
   is specified, the overall total data rate (the sum of all multicast
   groups) is bounded. However the required data rate in any particular
   group cannot be predicted, and may change quite rapidly during the
   simulation.

   DIS real time flow consists of packets of length around 2000 bits at
   rates from .2 packets per second per simulator to 15 packets per
   second per simulator. This information is intentionally redundant and
   is normally transmitted with a best effort transport protocol (UDP).
   In some cases it also is compressed.  Required accuracy both of
   latency and of physical simulation varies with the intended purpose
   but generally must be at least sufficient to satisfy human
   perception.  For example, in tightly coupled simulations such as high
   performance aircraft maximum acceptable latency is 100 milliseconds
   between any two hosts.  At relatively rare intervals events (e.g.
   collisions) may occur which require reliable transmission of some
   data, on a unicast basis, to any other host in the system.

   The U.S. DoD has a goal to build distributed simulation systems with
   up to 100,000 simulated objects, many of them computer generated
   forces that run with minimal human intervention, acting as opposing
   force or simulating friendly forces that are not available to
   participate.  DoD would like to carry out such simulations using a
   shared WAN.  Beyond DoD many people see a likelihood that distributed
   simulation capabilities may be commercialized as entertainment.  The
   scope of such an entertainment system is hard to predict but
   conceivably could be larger than the DoD goal of 100,000.



RFC 2502         Limitations of Internet Protocol Suite    February 1999


   The High Level Architecture (HLA) is a DoD development beyond DIS
   that aims at bringing DIS and other forms of distributed simulation
   into a unifying system paradigm. From a distributed systems
   standpoint HLA is considerably more sophisticated than DIS. For
   example attributes of distributed objects may be controlled by
   different simulators.  From the standpoint of the supporting network
   the primary difference between HLA and DIS is that HLA does not call
   for redundant transmission of object attributes; instead it specifies
   a "Run Time Infrastructure" (RTI) that is responsible to transmit
   data reliably, and may choose to do so by various means including
   redundant transmission using best effort protocols. It is reasonable
   to say that any network that can meet the needs of DIS can support
   HLA by DIS-like redundant transmission, however this approach ignores
   the possibility that under HLA some mixture of redundant and reliable
   transmission can make significantly better use of network resources
   than is possible using DIS.  While HLA, like DIS, does not specify
   use of a multicasting network, it has similar requirements for many-
   to-many transmission of object attributes at rates in excess of one
   update per object per second that cannot be met without multicasting.
   Further, HLA calls for transmission of semantically organized data
   (for example, groups of objects with similar capabilities such as
   tanks or aircraft) in this many-to-many context.

   One solution that has been employed to deal with these challenges is
   to aggregate the contents of many multicast groups into a single
   multicast transmission [PuWh95, CSTH95].  Termed "dual-mode" or "bi-
   level" multicast, this approach takes advantage of the fact that
   although the amount of traffic in any particular multicast group can
   vary greatly, the aggregate of all transmissions is bounded. If the
   traffic is all aggregated into one large flow, an underlying ATM
   network can create multicast SVCs with acceptable QoS to support the
   requirement. It also bounds the network control problem of group
   joins, in that the joins take place among dedicated collections of
   routers and across the dedicated SVCs, rather than contending with
   other LSMAs that may be sharing the same network. But it does this at
   the cost of adding to the network a new, nonstandard aggregation
   element that is a hybrid of the Internet and ATM protocols. We
   address below the requirement to achieve such a result using a purely
   IP network with aggregated reservation via RSVP.

   The defense distributed simulation community has created a number of
   multicast-capable networks for various simulated exercises, ranging
   from tens to hundreds of simulated objects distributed across numbers
   of sites ranging from two to twenty. As the number of objects has
   increased they have found that building multicasting networks
   potentially supporting thousands of simultaneous multicast groups
   with large group change rates is a hard problem. This defense problem
   is the precursor of similar problems that can be expected in



RFC 2502         Limitations of Internet Protocol Suite    February 1999


   commercial networks.  Therefore the following sections describe the
   services required and the shortcomings that have been found in using
   today's Internet protocols in providing these services, with the
   intention of informing the IETF to enable it to produce protocols
   that meet the needs in these areas.

2. Distributed Simulation (DIS and HLA) network service requirements.

   a. real-time packet delivery, with low packet loss (less than 2%),
   predictable latency on the order of a few hundred milliseconds, after
   buffering to account for jitter (variation of latency) such that less
   than 2% of packets fail to arrive within the specified latency, in a
   shared network

   b. multicasting with thousands of multicast groups that can support
   join latencies of less than one second, at rates of hundreds of joins
   per second

   c. multicasting using a many-to-many paradigm in which 90% or more of
   the group members act as receivers and senders within any given
   multicast group

   d. support for resource reservation; because of the impracticality of
   over-provisioning the WAN and the LAN for large distributed
   simulations, it is important to be able to reserve an overall
   capacity that can be dynamically allocated among the multicast groups

   e. support for a mixture of best-effort and reliable low-latency
   multicast transport, where best-effort predominates in the mixture,
   and the participants in the reliable multicast may be distributed
   across any portion of the network

   f. support for secure networking, in the form of per-packet
   encryption and authentication needed for classified military
   simulations

3. Internet Protocol Suite facilities needed and not yet available for
   large-scale distributed simulation in shared networks: These derive
   from the need for real-time multicast with established quality of
   service in a shared network.  (Implementation questions are not
   included in this discussion.  For example, it is not clear that
   implementations of IP multicast exist that will support the required
   scale of multicast group changes for LSMA, but that appears to be a
   question of implementation, not a limitation of IP multicast.)







RFC 2502         Limitations of Internet Protocol Suite    February 1999


3.1 Large-scale resource reservation in shared networks

   The Resource reSerVation Protocol (RSVP) is aimed at providing setup
   and flow-based information for managing information flows at pre-
   committed performance levels.  This capability is generally seen as
   needed in real-time systems such as the HLA RTI. Concerns have been
   raised about the scalability of RSVP, and also about its ability to
   support highly dynamic flow control changes.  In terms of existing
   RTI capabilities, the requirement in LSMA is for rapid change of
   group membership, not for rapid change of group reservations.  This
   is because in existing RTIs the aggregate requirement for all groups
   in a large scale distributed simulation is static. However the
   current RSVP draft standard for LSMA does not support aggregation of
   reservation resources for groups of flows and therefore does not meet
   the needs of existing RTIs.  Moreover, there is at least one RTI
   development underway that intends to use individual, dynamic
   reservations for large numbers of groups, and therefore will require
   a dynamic resource reservation capability that scales to thousands of
   multicast groups.

   Further, RSVP provides support only for communicating specifications
   of the required information flows between simulators and the network,
   and within the network.  Distributing routing information among the
   routers within the network is a different function altogether,
   performed by routing protocols such as Multicast Open Shortest Path
   First (MOSPF). In order to provide effective resource reservation in
   a large shared network function, it may be necessary to have a
   routing protocol that determines paths through the network within the
   context of a quality of service requirement.  An example is the
   proposed Quality Of Service Path First (QOSPF) routing protocol
   [ZSSC97]. Unfortunately the requirement for resource-sensitive
   routing will be difficult to define before LSMA networks are deployed
   with RSVP.

3.2 IP multicast that is capable of taking advantage of all common
    link layer protocols (in particular, ATM)

    Multicast takes advantage of the efficiency obtained when the
    network can recognize and replicate information packets that are
    destined to a group of locations. Under these circumstances, the
    network can take on the job of providing duplicate copies to all
    destinations, thereby greatly reducing the amount of information
    flowing into and through the network.

    When IP multicast operates over Ethernet, IP multicast packets are
    transmitted once and received by all receivers using Ethernet-layer
    multicast addressing, avoiding replication of packets.  However,
    with wide-area Asynchronous Transfer Mode (ATM), the ability to take



RFC 2502         Limitations of Internet Protocol Suite    February 1999


    advantage of data link layer multicast capability is not yet
    available beyond a single Logical IP Subnet (LIS).  This appears to
    be due to the fact that (1) the switching models of IP and ATM are
    sufficiently different that this capability will require a rather
    complex solution, and (2) there has been no clear application
    requirement for IP multicast over ATM multicast that provides for
    packet replication across multiple LIS.  Distributed simulation is
    an application with such a requirement.

3.3 Hybrid transmission of best-effort and reliable multicast

    In general the Internet protocol suite uses the Transmission Control
    Protocol (TCP) for reliable end-to-end transport, and the User
    Datagram Protocol (UDP) for best-effort end-to-end transport,
    including all multicast transport services.  The design of TCP is
    only capable of unicast transmission.

    Recently the IETF has seen proposals for several reliable multicast
    transport protocols (see [Mont97] for a summary). A general issue
    with reliable transport for multicast is the congestion problem
    associated with delivery acknowledgments, which has made real-time
    reliable multicast transport infeasible to date.  Of the roughly 15
    attempts to develop a reliable multicast transport, all have shown
    to have some problem relating to positive receipt acknowledgments
    (ACK) or negative acknowledgments (NAK). In any event, its seems
    clear that there is not likely to be a single solution for reliable
    multicast, but rather a number of solutions tailored to different
    application domains. Approaches involving distributed logging seem
    to hold particular promise for the distributed simulation
    application.

    In the DIS/HLA environment, five different transmission needs can be
    identified:

   (1) best-effort low-latency multicast of object attributes that often
       change continuously, for example position of mobile objects;
   (2) low-latency reliable multicast of object attributes that do not
       change continuously but may change at arbitrary times during the
       simulation, for example object appearance (An important
       characteristic of this category is that only the latest value of
       any attribute is needed by the receiver.);
   (3) low-latency, reliable unicast of occasional data among arbitrary
       members of the multicast group (This form of transmission was
       specified for DIS "collisions"; it is not in the current HLA
       specification but might profitably be included there. The
       requirement is for occasional transaction-like exchange of data
       between two arbitrary hosts in the multicast group, with a low
       latency that makes TCP connection impractical.);



RFC 2502         Limitations of Internet Protocol Suite    February 1999


   (4) reliable but not necessarily real-time multicast distribution of
       supporting bulk data such as terrain databases and object
       enumerations; and
   (5) reliable unicast of control information between individual RTI
       components (this requirement is met by TCP).

   All of these transmissions take place within the same large-scale
   multicasting environment. The value of integrating categories (1) and
   (2) into a single selectively reliable protocol was proposed by Cohen
   [Cohe94].  Pullen and Laviano implemented this concept [PuLa95] and
   demonstrated it within the HLA framework [PLM97] as the Selectively

   Reliable Transmission Protocol (SRTP) for categories (1) through (3).
   Category (4) could be supported by a reliable multicast protocol such
   as the commercial multicast FTP offering from Starburst [MRTW97],
   however adequate congestion control has not been demonstrated in any
   such protocol. There has been some discussion of using the Real-Time
   Streaming Protocol, RTSP, for this purpose, however as the databases
   must be transmitted reliably and RTSP uses a best-effort model, it
   does not appear to be applicable.

   In summary, it is clear that a hybrid of best-effort and reliable
   multicast (not necessarily all in the same protocol) is needed to
   support DIS and HLA, and that the low-latency, reliable part of this
   hybrid is not available in the Internet protocol suite.

3.4 Network management for distributed simulation systems

   Coordinated, integrated network management is one of the more
   difficult aspects of a large distributed simulation exercise.  The
   network management techniques that have been used successfully to
   support the growth of the Internet for the past several years could
   be expanded to fill this need.  The technique is based on a primitive
   called a Management Information Base (MIB) being polled periodically
   at very low data rates.  The receiver of the poll is called an Agent
   and is collocated with the remote process being monitored. The agent
   is simple so as to not absorb very many resources. The requesting
   process is called a Manager, and is typically located elsewhere on a
   separate workstation.  The Manager communicates to all of the agents
   in a given domain using the Simple Network Management Protocol
   (SNMP).  It appears that SNMP is well adapted to the purpose of
   distributed simulation management, in addition to managing the
   underlying simulation network resources.  Creating a standard
   distributed simulation MIB format would make it possible for the
   simulation community to make use of the collection of powerful, off-
   the-shelf network management tools that have been created around
   SNMP.




RFC 2502         Limitations of Internet Protocol Suite    February 1999


3.5 A session protocol to start, pause, and stop a distributed
    simulation exercise

   Coordinating start, stop, and pause of large distributed exercises is
   a complex and difficult task.  The Session Initiation Protocol (SIP)
   recently proposed by the Multiparty Multimedia Session Control
   (MMUSIC) working group serves a similar purpose for managing large
   scale multimedia conferences. As proposed, SIP appears to offer
   sufficient extensibility to be used for exercise session control, if
   standardized by the IETF.

3.6 An integrated security architecture

   It appears that this requirement will be met by IPv6 deployment. A
   shortcoming of the current Internet Protocol (IPv4) implementation is
   the lack of integrated security. The new IPv6 protocol requires
   implementers to follow an integrated security architecture that
   provides the required integrity, authenticity, and confidentiality
   for use of the Internet by communities with stringent security
   demands, such as the financial community.  The possibility that the
   IPv6 security architecture may meet military needs, when combined
   either with military cryptography or government-certified commercial
   cryptography, merits further study.

3.7 Low-latency multicast naming service

   Name-to-address mapping in the Internet is performed by the Domain
   Name Service (DNS).  DNS has a distributed architecture tuned to the
   needs of unicast networking with reliable transmission (TCP) that is
   not considered problematic if its latency is on the order of a second
   or more. The requirement of distributed simulation for agile movement
   among multicast groups implies a need for name-to-multicast-address
   mapping with latency of under one second for the name resolution and
   group join combined.  This problem has been circumvented in military
   simulations by using group IP addresses rather than names. While
   military simulations may be satisfied to communicate using a known
   mapping from grid squares to multicast groups, growth of distributed
   simulation into commercial entertainment cannot be based on such a
   simple capability. The players in distributed entertainment
   simulations will want to be organized symbolically by virtual world
   and role. A low-latency multicast naming service will be required.

3.8 Inter-Domain Multicast Routing for LSMA

   While military LSMAs typically take place within a single
   administrative domain, future entertainment LSMAs can be expected to
   involve heavy inter-domain multicast traffic so that players can be
   supported by multiple service providers.  Standardized protocols able



RFC 2502         Limitations of Internet Protocol Suite    February 1999


   to support large numbers of multicast flows across domain boundaries
   will be needed for this purpose.  Current work to create a Border
   Gateway Multicast Protocol (BGMP) shows promise of meeting this need.

4.  References

   [CSTH95]  Calvin, J., et. al., "STOW Realtime Information Transfer
             and Networking Architecture," 12th DIS Workshop on
             Standards for the Interoperability Distributed Simulations,
             March 1995.

   [Cohe94]  Cohen, D., "Back to Basics," Proceedings of the 11th
             Workshop on Standards for Distributed Interactive
             Simulation, Orlando, FL, September 1994.

   [DIS94]   DIS Steering Committee, "The DIS Vision," Institute for
             Simulation and Training, University of Central Florida, May
             1994.

   [DMSO96]  Defense Modeling and Simulation Office, High Level
             Architecture Rules Version 1.0, U.S. Department of Defense,
             August 1996.

   [IEEE95a] IEEE 1278.1-1995, Standard for Distributed Interactive
             Simulation - Application Protocols

   [IEEE95b] IEEE 1278.2-1995, Standard for Distributed Interactive
             Simulation - Communication services and Profiles

   [MRTW97]  Miller, K., et. al. "StarBurst Multicast File Transfer
             Protocol (MFTP) Specification", Work in Progress.

   [Mont97]  Montgomery, T., Reliable Multicast Links webpage,
             http://research.ivv.nasa.gov/RMP/links.html

   [PuLa95]  Pullen, M. and V. Laviano, "A Selectively Reliable
             Transport Protocol for Distributed Interactive Simulation",
             Proceedings of the 13th Workshop on Standards for
             Distributed Interactive Simulation, Orlando, FL, September
             1995.

   [PuWh95]  Pullen, M. and E. White, "Dual-Mode Multicast: A New
             Multicasting Architecture for Distributed Interactive
             Simulation," 12th DIS Workshop on Standards for the
             Interoperability of Distributed Simulations, Orlando, FL,
             March 1995.





RFC 2502         Limitations of Internet Protocol Suite    February 1999


   [PLM97]   Pullen, M., Laviano, V. and M. Moreau, "Creating A Light-
             Weight RTI As An Evolution Of Dual-Mode Multicast Using
             Selectively Reliable Transmission," Proceedings of the
             Second Simulation Interoperability Workshop, Orlando, FL,
             September 1997.

   [SPW94]   Symington, S., Pullen, M. and D. Wood, "Modeling and
             Simulation Requirements for IPng", RFC 1667, August 1994.

   [SSM96]   Seidensticker, S., Smith, W. and M. Myjak, "Scenarios and
             Appropriate Protocols for Distributed Interactive
             Simulation", Work in Progress.

   [ZSSC97]  Zhang, Z., et. al., "Quality of Service Path First Routing
             Protocol", Work in Progress.

4.  Security Considerations

   Security issues are discussed in section 3.6.

5.  Authors' Addresses

   J. Mark Pullen
   Computer Science/C3I Center
   MS 4A5
   George Mason University
   Fairfax, VA 22032

   EMail: mpullen@gmu.edu


   Michael Myjak
   The Virtual Workshop
   P.O. Box 98
   Titusville, FL 32781

   EMail: mmyjak@virtualworkshop.com


   Christina Bouwens
   ASSET Group, SAIC Inc.
   Orlando, FL

   EMail: christina.bouwens@cpmx.mail.saic.com







RFC 2502         Limitations of Internet Protocol Suite    February 1999


6.  Full Copyright Statement

   Copyright (C) The Internet Society (1999).  All Rights Reserved.

   This document and translations of it may be copied and furnished to
   others, and derivative works that comment on or otherwise explain it
   or assist in its implementation may be prepared, copied, published
   and distributed, in whole or in part, without restriction of any
   kind, provided that the above copyright notice and this paragraph are
   included on all such copies and derivative works.  However, this
   document itself may not be modified in any way, such as by removing
   the copyright notice or references to the Internet Society or other
   Internet organizations, except as needed for the purpose of
   developing Internet standards in which case the procedures for
   copyrights defined in the Internet Standards process must be
   followed, or as required to translate it into languages other than
   English.

   The limited permissions granted above are perpetual and will not be
   revoked by the Internet Society or its successors or assigns.

   This document and the information contained herein is provided on an
   "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
   TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
   BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
   HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
   MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.