| Rfc | 8202 |
|---|
| Title | IS-IS Multi-Instance |
|---|
| Author | L. Ginsberg, S. Previdi, W. Henderickx |
|---|
| Date | June
2017 |
|---|
| Format: | TXT, HTML |
|---|
| Obsoletes | RFC6822 |
|---|
| Status: | PROPOSED
STANDARD |
|---|
|
Internet Engineering Task Force (IETF) L. Ginsberg
Request for Comments: 8202 S. Previdi
Obsoletes: 6822 Cisco Systems
Category: Standards Track W. Henderickx
ISSN: 2070-1721 Nokia
June 2017
IS-IS Multi-Instance
Abstract
This document describes a mechanism that allows a single router to
share one or more circuits among multiple Intermediate System to
Intermediate System (IS-IS) routing protocol instances.
Multiple instances allow the isolation of resources associated with
each instance. Routers will form instance-specific adjacencies.
Each instance can support multiple topologies. Each topology has a
unique Link State Database (LSDB). Each Protocol Data Unit (PDU)
will contain a new Type-Length-Value (TLV) identifying the instance
and the topology (or topologies) to which the PDU belongs.
This document obsoletes RFC 6822.
Status of This Memo
This is an Internet Standards Track document.
This document is a product of the Internet Engineering Task Force
(IETF). It represents the consensus of the IETF community. It has
received public review and has been approved for publication by the
Internet Engineering Steering Group (IESG). Further information on
Internet Standards is available in Section 2 of RFC 7841.
Information about the current status of this document, any errata,
and how to provide feedback on it may be obtained at
http://www.rfc-editor.org/info/rfc8202.
Copyright Notice
Copyright (c) 2017 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction ....................................................3
2. Requirements Language ...........................................4
3. Elements of Procedure ...........................................4
3.1. Instance Identifier TLV ....................................4
3.2. Instance Membership ........................................6
3.3. Use of Authentication ......................................6
3.4. Adjacency Establishment ....................................6
3.4.1. Point-to-Point Adjacencies ..........................6
3.4.2. Multi-Access Adjacencies ............................7
3.5. Update Process Operation ...................................7
3.5.1. Update Process Operation on Point-to-Point
Circuits ............................................7
3.5.2. Update Process Operation on Broadcast Circuits ......7
3.6. Interoperability Considerations ............................7
3.6.1. Interoperability Issues on Broadcast Circuits .......8
3.6.2. Interoperability Using Point-to-Point Circuits ......9
4. Usage Guidelines ................................................9
4.1. One-to-One Mapping between Topologies and Instances .......10
4.2. Many-to-One Mapping between Topologies and Instances ......10
4.3. Considerations for the Number of Instances ................11
5. Relationship to M-ISIS .........................................11
6. Graceful Restart Interactions ..................................12
7. IANA Considerations ............................................12
8. Security Considerations ........................................12
9. References .....................................................12
9.1. Normative References ......................................12
9.2. Informative References ....................................14
Appendix A. Changes to RFC 6822 ...................................15
Acknowledgements ..................................................15
Authors' Addresses ................................................16
1. Introduction
An existing limitation of the protocol defined by [ISO10589] is that
only one instance of the protocol can operate on a given circuit.
This document defines an extension to IS-IS to remove this
restriction. The extension is referred to as "Multi-Instance IS-IS"
(MI-IS-IS).
Routers that support this extension are referred to as "Multi-
Instance-capable routers" (MI-RTR).
The use of multiple instances enhances the ability to isolate the
resources associated with a given instance both within a router and
across the network. Instance-specific prioritization for processing
PDUs and performing routing calculations within a router may be
specified. Instance-specific flooding parameters may also be defined
so as to allow different instances to consume network-wide resources
at different rates.
Another existing protocol limitation is that a given instance
supports a single Update Process operating on a single Link State
Database (LSDB). This document defines an extension to IS-IS to
allow non-zero instances of the protocol to support multiple Update
Processes. Each Update Process is associated with a topology and a
unique topology-specific LSDB. Non-zero instances of the protocol
are only supported by MI-RTRs. Legacy routers support the standard
or zero instance of the protocol. The behavior of the standard
instance is not changed in any way by the extensions defined in this
document.
MI-IS-IS might be used to support topology-specific routing. Two
methods of supporting such a use are defined in this document: one
supports the use of [RFC5120] within a reserved instance-specific
topology and the other is an alternative to [RFC5120] that supports
topology-specific flooding of link state information.
MI-IS-IS might also be used to support the advertisement of
information on behalf of applications [RFC6823]. The advertisement
of information not directly related to the operation of the IS-IS
protocol can therefore be done in a manner that minimizes its impact
on the operation of routing.
The above are examples of how MI-IS-IS might be used. The
specification of uses of MI-IS-IS is outside the scope of this
document.
2. Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in
BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all
capitals, as shown here.
3. Elements of Procedure
An Instance Identifier (IID) is introduced to uniquely identify an
IS-IS instance. The protocol extension includes a new TLV (IID-TLV)
in each IS-IS PDU originated by an MI-RTR except as noted in this
document. The IID-TLV identifies the unique instance as well as the
instance-specific topology/topologies to which the PDU applies. Each
IS-IS PDU is associated with only one IS-IS instance.
MI-RTRs form instance-specific adjacencies. The IID-TLV included in
IS-IS Hellos (IIHs) includes the IID and the set of Instance-specific
Topology Identifiers (ITIDs) that the sending IS supports. When
multiple instances share the same circuit, each instance will have a
separate set of adjacencies.
MI-RTRs support the exchange of topology-specific Link State PDUs for
the IID/ITID pairs that each neighbor supports. A unique IS-IS
Update Process (see [ISO10589]) operates for each IID/ITID pair.
This MAY also imply IID/ITID-specific routing calculations and
IID/ITID-specific routing and forwarding tables. However, this
aspect is outside the scope of this specification.
The mechanisms used to implement support of the separation of IS-IS
instances and topology-specific Update Processes within a router are
outside the scope of this specification.
3.1. Instance Identifier TLV
A new TLV is defined in order to convey the IID and ITIDs supported.
The IID-TLV associates a PDU with an IS-IS instance using a unique
16-bit number. The IID-TLV is carried in all IS-IS PDUs that are
associated with a non-zero instance; this includes IIHs, Sequence
Number PDUs (SNPs), and Link State PDUs (LSPs) .
Multiple instances of IS-IS may coexist on the same circuit and on
the same physical router. IIDs MUST be unique within the same
routing domain.
IID #0 is reserved for the standard instance supported by legacy
systems. IS-IS PDUs associated with the standard instance MUST NOT
include an IID-TLV except where noted in this document.
The IID-TLV MAY include one or more ITIDs. An ITID is a 16-bit
identifier where all values (0 - 65535) are valid.
The following format is used for the IID-TLV:
Type: 7
Length: 2 - 254
Value:
No. of octets
+-------------------------+
| IID (0 - 65535) | 2
+-------------------------+
| Supported ITID | 2
+-------------------------+
: :
+-------------------------+
| Supported ITID | 2
+-------------------------+
When the IID = 0, the list of supported ITIDs MUST NOT be present.
An IID-TLV with IID = 0 MUST NOT appear in an SNP or LSP. When
the TLV appears (with a non-zero IID) in an SNP or LSP, exactly
one ITID MUST be present, indicating the instance-specific
topology with which the PDU is associated. If no ITIDs or
multiple ITIDs are present or the IID is zero, then the PDU MUST
be ignored.
When the IID is non-zero and the TLV appears in an IIH, the set of
ITIDs supported on the circuit over which the IIH is sent is
included. There MUST be at least one ITID present.
ITID #0 is reserved for a specific use case as described later in
this document. ITID #0 MUST NOT be supported in combination with
any non-zero ITID. If multiple ITIDs are advertised in an IIH and
one of the ITIDs is #0, then the PDU MUST be ignored.
Multiple IID-TLVs MAY appear in IIHs. If multiple IID-TLVs are
present and the IID value in all IID-TLVs is not the same, then
the PDU MUST be ignored.
A single IID-TLV will support advertisement of up to 126 ITIDs. If
multiple IID-TLVs are present in an IIH PDU, the supported set of
ITIDs is the union of all ITIDs present in all IID-TLVs.
When an LSP purge is initiated, the IID-TLV MUST be retained, but the
remainder of the body of the LSP SHOULD be removed. The purge
procedure is described in [RFC6233] and [RFC6232].
It is recommended that (when present) the IID-TLV(s) be the first
TLV(s) in the PDU. This allows determination of the association of a
PDU with a particular instance more quickly.
A PDU without an IID-TLV belongs to the standard instance.
3.2. Instance Membership
Each MI-RTR is configured to be participating in one or more
instances of IS-IS. For each non-zero instance in which it
participates, an MI-RTR marks IS-IS PDUs (IIHs, LSPs, or SNPs)
generated that pertain to that instance by including the IID-TLV with
the appropriate instance identifier.
3.3. Use of Authentication
When authentication is in use, the IID, if present, is first used to
select the authentication configuration that is applicable. The
authentication check is then performed as normal. When multiple
ITIDs are supported, ITID-specific authentication MAY be used in SNPs
and LSPs.
3.4. Adjacency Establishment
In order to establish adjacencies, IS-IS routers exchange IIH PDUs.
Two types of adjacencies exist in IS-IS: point-to-point and
broadcast. The following subsections describe the additional rules
an MI-RTR MUST follow when establishing adjacencies for non-zero
instances.
3.4.1. Point-to-Point Adjacencies
MI-RTRs include the IID-TLV in the point-to-point Hello PDUs
associated with non-zero instances that they originate. Upon
reception of an IIH, an MI-RTR inspects the received IID-TLV, and if
the IID matches any of the IIDs that the router supports on that
circuit, normal adjacency establishment procedures are used to
establish an instance-specific adjacency. Note that the absence of
the IID-TLV implies IID #0. For instances other than IID #0, an
adjacency SHOULD NOT be established unless there is at least one ITID
in common.
This extension allows an MI-RTR to establish multiple adjacencies to
the same physical neighbor over a point-to-point circuit. However,
as the instances are logically independent, the normal expectation of
at most one neighbor on a given point-to-point circuit still applies.
3.4.2. Multi-Access Adjacencies
Multi-Access (broadcast) circuits behave differently than point-to-
point in that PDUs sent by one router are visible to all routers and
all routers must agree on the election of a Designated Intermediate
System (DIS) independent of the set of ITIDs supported.
MI-RTRs will establish adjacencies and elect a DIS per IS-IS
instance. Each MI-RTR will form adjacencies only with routers that
advertise support for the instances that the local router has been
configured to support on that circuit. Since an MI-RTR is not
required to support all possible instances on a LAN, it's possible to
elect a different DIS for different instances.
3.5. Update Process Operation
For non-zero instances, a unique Update Process exists for each
supported ITID.
3.5.1. Update Process Operation on Point-to-Point Circuits
On Point-to-Point circuits -- including Point-to-Point Operation over
LAN [RFC5309] -- the ITID-specific Update Process only operates on
that circuit for those ITIDs that are supported by both ISs operating
on the circuit.
3.5.2. Update Process Operation on Broadcast Circuits
On broadcast circuits, a single DIS is elected for each supported IID
independent of the set of ITIDs advertised in LAN IIHs. This
requires that the DIS generate pseudo-node LSPs for all supported
ITIDs and that the Update Process for all supported ITIDs operate on
the broadcast circuit. Among MI-RTRs operating on a broadcast
circuit, if the set of supported ITIDs for a given non-zero IID is
inconsistent, connectivity for the topology (or topologies)
associated with the ITIDs not supported by some MI-RTRs can be
compromised.
3.6. Interoperability Considerations
[ISO10589] requires that any TLV that is not understood be silently
ignored without compromising the processing of the whole IS-IS PDU
(IIH, LSP, SNP).
To a router not implementing this extension, all IS-IS PDUs received
will appear to be associated with the standard instance, regardless
of whether an IID-TLV is present in those PDUs. This can cause
interoperability issues unless the mechanisms and procedures
discussed below are followed.
3.6.1. Interoperability Issues on Broadcast Circuits
In order for routers to correctly interoperate with routers not
implementing this extension and in order not to cause disruption, a
specific and dedicated Media Access Control (MAC) address is used for
multicasting IS-IS PDUs with any non-zero IID. Each level will use a
specific Layer 2 multicast address. Such an address allows MI-RTRs
to exchange IS-IS PDUs with non-zero IIDs without these PDUs being
processed by legacy routers; therefore, no disruption is caused.
When sending SNPs, LSPs, and LAN IIHs for the standard instance (IID
#0), an MI-RTR will use either the AllL1IS or the AllL2IS MAC-layer
addresses (as defined in [ISO10589]) as the destination address.
When sending SNPs, LSPs, and LAN IIHs for any non-zero IID, an MI-RTR
MUST use one of two new dedicated Layer 2 multicast addresses
(AllL1MI-ISs or AllL2MI-ISs) as the destination address. These
addresses are specified in Section 7.
MI-RTRs MUST discard IS-IS PDUs received if either of the following
is true:
o The destination multicast address is AllL1IS, AllL2IS, or AllIS
and the PDU contains an IID-TLV.
o The destination multicast address is AllL1MI-ISs or AllL2MI-ISs
and the PDU contains an IID-TLV with a zero value for the IID or
has no IID-TLV.
NOTE: If the multicast addresses AllL1IS, AllL2IS, and/or AllIS are
improperly used to send IS-IS PDUs for non-zero IIDs, legacy systems
will interpret these PDUs as being associated with IID #0. This will
cause inconsistencies in the LSDB in those routers, may incorrectly
maintain adjacencies, and may lead to inconsistent DIS election.
3.6.1.1. Special Considerations when Operating in Point-to-Point Mode
When operating in point-to-point mode on a broadcast circuit
[RFC5309], an MI-RTR will use AllL1IS, AllL2IS, or AllIS MAC-layer
addresses when sending SNPs, LSPs, and point-to-point IIHs associated
with the standard instance. When sending SNPs, LSPs, and point-to-
point IIHs for a non-zero IID, an MI-RTR MUST use one of the two new
multicast addresses (AllL1MI-ISs or AllL2MI-IS) as the destination
address. When sending point-to-point IIHs for a non-zero IID, either
address is permitted.
3.6.2. Interoperability Using Point-to-Point Circuits
In order for an MI-RTR to interoperate over a point-to-point circuit
with a router that does NOT support this extension, the MI-RTR MUST
NOT send IS-IS PDUs for instances other than IID #0 over the point-
to-point circuit as these PDUs may affect the state of IID #0 in the
neighbor.
The presence or absence of the IID-TLV in an IIH indicates that the
neighbor does or does not support this extension, respectively.
Therefore, all IIHs sent on a point-to-point circuit by an MI-RTR
MUST include an IID-TLV. This includes IIHs associated with IID #0.
Once it is determined that the neighbor does not support this
extension, an MI-RTR MUST NOT send PDUs (including IIHs) for
instances other than IID #0.
Until an IIH is received from a neighbor, an MI-RTR MAY send IIHs for
a non-zero instance. However, once an IIH with no IID-TLV has been
received (indicating that the neighbor is not an MI-RTR), the MI-RTR
MUST NOT send IIHs for a non-zero instance. The temporary relaxation
of the restriction on sending IIHs for non-zero instances allows a
non-zero instance adjacency to be established on an interface on
which an MI-RTR does NOT support the standard instance.
Point-to-point adjacency setup MUST be done through the use of the
three-way handshaking procedure as defined in [RFC5303] in order to
prevent a non-MI-capable neighbor from bringing up an adjacency
prematurely based on reception of an IIH with an IID-TLV for a
non-zero instance.
4. Usage Guidelines
As discussed above, MI-IS-IS extends IS-IS to support multiple
instances on a given circuit. Each instance is uniquely identified
by the IID and forms instance-specific adjacencies. Each instance
supports one or more topologies as represented by the ITIDs. All
topologies associated with a given instance share the instance-
specific adjacencies. The set of topologies supported by a given IID
MAY differ from circuit to circuit. Each topology has its own set of
LSPs and runs a topology-specific Update Process. Flooding of
topology-specific LSPs is only performed on circuits on which both
the local router and the neighbor(s) support a given topology (i.e.,
advertise the same ITID in the set of supported ITIDs sent in the
IID-TLV included in IIHs).
The following subsections provide some guidelines for usage of
instances and topologies within each instance. While this represents
examples based on the intent of the authors, implementors are not
constrained by the examples.
4.1. One-to-One Mapping between Topologies and Instances
When the set of information to be flooded in LSPs is intended to be
flooded to all MI-RTRs supporting a given IID, a single topology MAY
be used. The information contained in the single LSDB MAY still
contain information associated with multiple applications as the
GENINFO TLV for each application has an application-specific ID that
identifies the application to which the TLV applies [RFC6823].
4.2. Many-to-One Mapping between Topologies and Instances
When the set of information to be flooded in LSPs includes subsets
that are of interest to a subset of the MI-RTRs supporting a given
IID, support of multiple ITIDs allows each subset to be flooded only
to those MI-RTRs that are interested in that subset. In the simplest
case, a one-to-one mapping between a given application and an ITID
allows the information associated with that application to be flooded
only to MI-RTRs that support that application -- but a many-to-one
mapping between applications and a given ITID is also possible. When
the set of application-specific information is large, the use of
multiple ITIDs provides significantly greater efficiencies, as
MI-RTRs only need to maintain the LSDB for applications of interest
and that information only needs to be flooded over a topology defined
by the MI-RTRs who support a given ITID.
The use of multiple ITIDs also allows the dedication of a full LSP
set (256 LSPs at each level) for the use of a given (set of)
applications, thereby minimizing the possibility of exceeding the
carrying capacity of an LSP set. Such a possibility might arise if
information for all applications were to be included in a single LSP
set.
Note that the topology associated with each ITID MUST be fully
connected in order for ITID-specific LSPs to be successfully flooded
to all MI-RTRs that support that ITID.
When multiple ITIDs are supported by an instance, ITID #0 MUST NOT be
supported.
4.3. Considerations for the Number of Instances
The support of multiple topologies within the context of a single
instance provides better scalability in support of multiple
applications both in terms of the number of adjacencies that are
required and in the flooding of topology-specific LSDB. In many
cases, the use of a single non-zero instance would be sufficient and
optimal. However, in cases where the set of topologies desired in
support of a set of applications is largely disjoint from the set of
topologies desired in support of a second set of applications, it
could make sense to use multiple instances.
5. Relationship to M-ISIS
[RFC5120] defines support for multi-topology routing. In that
document, 12-bit Multi-Topology Identifiers (MTIDs) are defined to
identify the topologies that an IS-IS instance (a "standard instance"
as defined by this document) supports. There is no relationship
between the MTIDs defined in [RFC5120] and the ITIDs defined in this
document.
An MI-RTR MAY use the extensions defined in this document to support
multiple topologies in the context of an instance with a non-zero
IID. Each MI topology is associated with a unique LSDB identified by
an ITID. An ITID-specific IS-IS Update Process operates on each
topology. This differs from [RFC5120], where a single LSDB and
single IS-IS Update Process are used in support of all topologies.
In such cases, if an MI-RTR uses the extensions in support of the
BFD-Enabled TLV [RFC6213], the ITID MUST be used in place of the
MTID; in which case, all 16 bits of the identifier field are useable.
An MI-RTR MAY support [RFC5120] multi-topology within a non-zero
instance when ITID #0 is supported. When ITID #0 is supported it
MUST be the only ITID supported by that instance. In such cases, if
an MI-RTR uses the extensions in support of the BFD Enabled TLV
[RFC6213] the [RFC5120] MTID MUST be used as specified in [RFC6213].
An MI-RTR MUST NOT support [RFC5120] multi-topology within a non-zero
instance when any non-zero ITID is supported. The following TLVs
MUST NOT be sent in an LSP associated with a non-zero instance that
supports a non-zero ITID, and such an LSP MUST be ignored when
received:
TLV 222 - MT IS Neighbors
TLV 235 - MT IP Reachability
TLV 237 - MT IPv6 Reachability
6. Graceful Restart Interactions
[RFC5306] defines protocol extensions in support of graceful restart
of a routing instance. The extensions defined there apply to MI-RTRs
with the notable addition that as there are topology-specific LSP
databases all of the topology-specific LSP databases must be
synchronized following restart in order for database synchronization
to be complete. This involves the use of additional T2 timers. See
[RFC5306] for further details.
7. IANA Considerations
IANA has registered an IS-IS TLV, reflected in the "IS-IS TLV
Codepoints Registry":
Value Name IIH LSP SNP Purge
---- --------------------- --- --- --- -----
7 Instance Identifier y y y y
Per [RFC6822], IANA has registered two EUI-48 multicast addresses
from the IANA-managed EUI address space as specified in [RFC7042].
The addresses are as follows:
01-00-5E-90-00-02 AllL1MI-ISs
01-00-5E-90-00-03 AllL2MI-ISs
All references to [RFC6822] in the "IS-IS TLV Codepoints Registry"
and the "IANA Multicast 48-bit MAC Addresses" registry have been
replaced by references to this document.
8. Security Considerations
Security concerns for IS-IS are addressed in [ISO10589], [RFC5304],
and [RFC5310].
9. References
9.1. Normative References
[ISO10589]
International Organization for Standardization,
"Information technology -- Telecommunications and
information exchange between systems -- Intermediate
System to Intermediate System intra-domain routeing
information exchange protocol for use in conjunction with
the protocol for providing the connectionless-mode network
service (ISO 8473)", ISO/IEC 10589:2002, Second Edition,
November 2002.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<http://www.rfc-editor.org/info/rfc2119>.
[RFC5120] Przygienda, T., Shen, N., and N. Sheth, "M-ISIS: Multi
Topology (MT) Routing in Intermediate System to
Intermediate Systems (IS-ISs)", RFC 5120,
DOI 10.17487/RFC5120, February 2008,
<http://www.rfc-editor.org/info/rfc5120>.
[RFC5303] Katz, D., Saluja, R., and D. Eastlake 3rd, "Three-Way
Handshake for IS-IS Point-to-Point Adjacencies", RFC 5303,
DOI 10.17487/RFC5303, October 2008,
<http://www.rfc-editor.org/info/rfc5303>.
[RFC5304] Li, T. and R. Atkinson, "IS-IS Cryptographic
Authentication", RFC 5304, DOI 10.17487/RFC5304, October
2008, <http://www.rfc-editor.org/info/rfc5304>.
[RFC5306] Shand, M. and L. Ginsberg, "Restart Signaling for IS-IS",
RFC 5306, DOI 10.17487/RFC5306, October 2008,
<http://www.rfc-editor.org/info/rfc5306>.
[RFC5310] Bhatia, M., Manral, V., Li, T., Atkinson, R., White, R.,
and M. Fanto, "IS-IS Generic Cryptographic
Authentication", RFC 5310, DOI 10.17487/RFC5310, February
2009, <http://www.rfc-editor.org/info/rfc5310>.
[RFC6213] Hopps, C. and L. Ginsberg, "IS-IS BFD-Enabled TLV",
RFC 6213, DOI 10.17487/RFC6213, April 2011,
<http://www.rfc-editor.org/info/rfc6213>.
[RFC6232] Wei, F., Qin, Y., Li, Z., Li, T., and J. Dong, "Purge
Originator Identification TLV for IS-IS", RFC 6232,
DOI 10.17487/RFC6232, May 2011,
<http://www.rfc-editor.org/info/rfc6232>.
[RFC6233] Li, T. and L. Ginsberg, "IS-IS Registry Extension for
Purges", RFC 6233, DOI 10.17487/RFC6233, May 2011,
<http://www.rfc-editor.org/info/rfc6233>.
[RFC6822] Previdi, S., Ed., Ginsberg, L., Shand, M., Roy, A., and D.
Ward, "IS-IS Multi-Instance", RFC 6822,
DOI 10.17487/RFC6822, December 2012,
<http://www.rfc-editor.org/info/rfc6822>.
[RFC6823] Ginsberg, L., Previdi, S., and M. Shand, "Advertising
Generic Information in IS-IS", RFC 6823,
DOI 10.17487/RFC6823, December 2012,
<http://www.rfc-editor.org/info/rfc6823>.
[RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
May 2017, <http://www.rfc-editor.org/info/rfc8174>.
9.2. Informative References
[Err4519] RFC Errata, Erratum ID 4519, RFC 6822.
[Err4520] RFC Errata, Erratum ID 4520, RFC 6822.
[RFC5309] Shen, N., Ed. and A. Zinin, Ed., "Point-to-Point Operation
over LAN in Link State Routing Protocols", RFC 5309,
DOI 10.17487/RFC5309, October 2008,
<http://www.rfc-editor.org/info/rfc5309>.
[RFC7042] Eastlake 3rd, D. and J. Abley, "IANA Considerations and
IETF Protocol and Documentation Usage for IEEE 802
Parameters", BCP 141, RFC 7042, DOI 10.17487/RFC7042,
October 2013, <http://www.rfc-editor.org/info/rfc7042>.
Appendix A. Changes to RFC 6822
RFC 6822 prohibited the use of Multi-Topology (MT) support as
described in RFC 5120 in a non-zero instance. However, deployment
experience since the writing of RFC 6822 has revealed a desire to be
able to support the style of MT in RFC 5120 using multiple non-zero
instances as an alternative means of controlling leaking of
information between L1 areas while also supporting incongruent
topologies for different address families. The rules have therefore
been relaxed to allow use of MT per RFC 5120 in a non-zero instance
so long as ITID #0 is the only instance topology (ITID) supported by
the instance. Note that this change is not backwards compatible with
implementations strictly following RFC 6822. As of this writing, all
known implementations are compatible with this change.
A suggestion has been added to place the IID-TLV as the first TLV in
a PDU to speed recognition of the correct instance when parsing a
received PDU.
Clarification that when operating in point-to-point mode on a
broadcast circuit the IID-TLV is only included in point-to-point IIHs
associated with non-zero instances has been added. This addresses
Errata ID 4519 [Err4519].
Clarification of the appropriate MAC multicast addresses to use when
sending PDUs on a broadcast interface for both standard instance and
non-zero instances has been provided. This addresses Errata ID 4520
[Err4520].
Acknowledgements
The authors greatly acknowledge Mike Shand, Abhay Roy, and Dave Ward
for their contributions as coauthors of RFC 6822. In addition, we
note that RFC 6822 acknowledged contributions made by Dino Farinacci
and Tony Li.
The authors of this document would also like to thank Paul Wells.
Authors' Addresses
Les Ginsberg
Cisco Systems
821 Alder Drive
Milpitas, CA 95035
United States of America
Email: ginsberg@cisco.com
Stefano Previdi
Cisco Systems
Via Del Serafico 200
Rome 0144
Italy
Email: sprevidi@cisco.com
Wim Henderickx
Nokia
Belgium
Email: wim.henderickx@nokia.com