| Rfc | 2458 |
|---|
| Title | Toward the PSTN/Internet Inter-Networking--Pre-PINT Implementations |
|---|
| Author | H. Lu, M. Krishnaswamy, L. Conroy, S. Bellovin, F. Burg, A.
DeSimone, K. Tewani, P. Davidson, H. Schulzrinne, K. Vishwanathan |
|---|
| Date | November 1998 |
|---|
| Format: | TXT, HTML |
|---|
| Status: | INFORMATIONAL |
|---|
|
Netowrk Working Group H. Lu
Request for Comments: 2458 Editor
Category: Informational M. Krishnaswamy
Lucent Technologies
L. Conroy
Roke Manor Research
S. Bellovin
F. Burg
A. DeSimone
K. Tewani
AT&T Labs
P. Davidson
Nortel
H. Schulzrinne
Columbia University
K. Vishwanathan
Isochrome
November 1998
Toward the PSTN/Internet Inter-Networking
--Pre-PINT Implementations
Status of this Memo
This memo provides information for the Internet community. It does
not specify an Internet standard of any kind. Distribution of this
memo is unlimited.
Copyright Notice
Copyright (C) The Internet Society (1998). All Rights Reserved.
Abstract
This document contains the information relevant to the development of
the inter-networking interfaces underway in the Public Switched
Telephone Network (PSTN)/Internet Inter-Networking (PINT) Working
Group. It addresses technologies, architectures, and several (but by
no means all) existing pre-PINT implementations of the arrangements
through which Internet applications can request and enrich PSTN
telecommunications services. The common denominator of the enriched
services (a.k.a. PINT services) is that they combine the Internet and
PSTN services in such a way that the Internet is used for non-voice
interactions, while the voice (and fax) are carried entirely over the
PSTN. One key observation is that the pre-PINT implementations, being
developed independently, do not inter-operate. It is a task of the
PINT Working Group to define the inter-networking interfaces that
will support inter-operation of the future implementations of PINT
services.
Table of Contents
1. Introduction ....................................... 3
2. Terminology ....................................... 3
3. PINT Services ....................................... 4
4. Architectural Overview ............................... 5
4.1 Public Switched Telephone Network ............... 5
4.2 Pre-PINT Systems ............................... 9
5. IN-Based Solutions ............................... 20
5.1 The Lucent System ............................... 20
5.1.1 Roles of the Web Server, Service Node, and SMS ....... 20
5.1.2 A Click-to-Dial-Back Service Scenario ............... 21
5.1.3 Web Server-Service Node Interface ............... 22
5.1.4 Web Server-SMS Interface and SNMP MIB ............... 24
5.1.5 Security Considerations ........................... 26
5.2 Siemens Web Call Center ........................... 27
5.2.1 Service Description ............................... 27
5.2.2 Implementation ................................... 29
5.2.3 Derived Requirements/Lessons ..................... 35
6. Alternative Solutions ............................... 37
6.1 The AT&T System ..................................... 37
6.1.1 High Level Architecture ............................ 38
6.1.2 IP Client to CallBroker Interface .................. 39
6.1.3 Protocol ........................................... 40
6.1.4 APIs Exposed to the IP Client ..................... 41
6.1.5 Voice-Bridge Control API ........................ 41
6.2 Simple Computer Telephony Protocol ............... 41
6.2.1 Overview ........................................... 41
6.2.2 How SCTP Fits in with the Reference PINT Services .. 42
7. Session Initiation Protocol--An Emerging Standard .. 43
7.1 Overview ....................................... 43
7.2 SIP Protocol ....................................... 44
7.3 SIP Entities ....................................... 45
7.4 Providing Call Control Functionality ............... 46
8. Overall Security Considerations ..................... 47
9. Conclusion ....................................... 48
10. Acknowledgments ................................... 48
11. Appendix ....................................... 49
11.1 PSTN/IN 101 ....................................... 49
11.1.1 Public Switched Telephone Network ............... 49
11.1.2 Intelligent Network ............................... 51
11.2 Call Center Features ............................. 54
12. References ....................................... 56
Authors' Addresses ......................................... 57
Full Copyright Statement .................................. 60
1. Introduction
This document contains the information relevant to the development of
the inter-networking interfaces underway in the Public Switched
Telephone Network (PSTN)/Internet Inter-Networking (PINT) Working
Group. It addresses technologies, architectures, and several (but by
no means all) existing pre-PINT implementations of the arrangements
through which Internet applications can request and enrich PSTN
telecommunications services. The common denominator of the enriched
services (a.k.a. PINT services) is that they combine the Internet and
PSTN services in such a way that the Internet is used for non-voice
interactions, while the voice (and fax) are carried entirely over the
PSTN.
The organization of the document is as follows. First, the basic
terminology and a short "intuitive" description of the PINT services
are provided. The rest of the information deals, in one way or the
other, with the pre-PINT support of these services where they are
used as a benchmark. Thus, an architectural overview common to all
present solutions is presented. The flow of the document then
divides into two streams: one is dedicated to the Intelligent Network
(IN)-based solutions; the other explores alternative means (i.e.,
CallBroker and Computer-Telephony Integration (CTI) approach). At
this point, the emerging standards are explored, in particular, the
Session Initiation Protocol (SIP), which promises an elegant solution
to the PINT problem. Each of the above developments is addressed in a
respective section. The final sections of the document contain the
overall security considerations, conclusion, acknowledgments,
appendix, and a set of references. The security section summarizes
the PINT security requirements derived from the pre-PINT experiences
and the appendix presents a tutorial on the PSTN, IN, and Call Center
functions.
2. Terminology
This document uses the following terminology:
Authentication -- verification of the identity of a party.
Authorization -- determination of whether or not a party has the
right to perform certain activities.
PINT Gateway -- the PSTN node that interacts with the Internet.
User or Customer -- the person who asks for a service request to be
issued. In the context of PINT Services, this person will use an
Internet host to make his or her request. The term "user" is also
used to describe a host originating the PINT service request on
behalf of this person.
3. PINT Services
This document addresses four services initially identified by the
PINT Working Group and presently supported by pre-PINT
implementations. These services are: click-to-dial-back, click-to-
fax, click-to-fax-back and voice-access-to-content.
Note that the word "click" should not be taken literally. It is
rather used to point out that initiation of the related services
takes place on the Internet, where point and click are the most
prevalent user actions. In other words, a service request could
originate from any type of IP-based platforms. There is no
implication that these services must be implemented by a device
within the PSTN or the Internet running a Web server.
The common denominator of the PINT services is that they combine the
Internet and PSTN services in such a way that the Internet is used
for non-voice interactions, while the voice (and fax) are carried
entirely over the PSTN. (An example of such a service is combination
of a Web-based Yellow Pages service with the ability to initiate PSTN
calls between customers and suppliers in a manner described in what
follows.)
Some of the benefits of using the PSTN are high quality of the voice,
an ability to route the call to different locations depending on
pre-set criteria (for example, time of the day, day of the week, and
geographic location), outstanding security and reliability, and
access to flexible, low cost, and secure billing and charging
systems. The benefits of using the Internet are the uniform, well-
defined, and widely-used interfaces available anywhere, anytime.
Click-to-Dial-Back
With this service, a user requests (through an IP host) that the PSTN
call be established between another party and himself or herself. An
important pre-requisite for using this service is that the user has
simultaneous access to both the PSTN and Internet.
One example of an application of this service is on-line shopping: a
user browsing through an on-line catalogue, clicks a button thus
inviting a call from a sales representative. Note that (as is the
case with the all-PSTN Free-Phone, or "800", service) flexible
billing arrangements can be implemented here on behalf of the service
provider. In addition (and also similarly to the Free-Phone/800), the
PSTN could route the call depending on the time of day, day of week,
availability of agents in different locations, and so on.
Click-to-Fax
With this service, a user at an IP host requests that a fax be sent
to a particular fax number. In particular this service is especially
meaningful when the fax is to be sent to someone who has only a fax
machine (but no access to the Internet). Consider, as an example, a
service scenario in which a Web user makes a reservation for a hotel
room in Beijing from a travel service page containing hotel
information of major cities around the world. Suppose a specific
Beijing hotel chosen by the user does not have Internet connection
but has a fax machine. The user fills out the hotel reservation form
and then clicks a button sending out the form to the travel service
provider, which in turn generates a fax request and sends it together
with the hotel reservation form to the PSTN. Upon receiving the
request and the associated data, the PSTN translates the data into
the proper facsimile format and delivers it to the Beijing hotel as
specified in the fax request.
Click-to-Fax-Back
With this service, a user at an IP host can request that a fax be
sent to him or her. (Consider the user of the previous example, who
now requests the confirmation from the Beijing Hotel. Another useful
application of the service is when size of the information that a
user intends to get is so large that downloading it to the user's PC
over the Internet will require a long time and a lot of disk space.)
Voice-Access-to-Content
With this service, a user at an IP host requests that certain
information on the Internet be accessed (and delivered) in an audio
form over the PSTN, using the telephone as an informational
appliance. One application of this service is to provide Web access
to the blind. (This may require special resources--available in the
PSTN--to convert the Web data into speech.)
4. Architectural Overview
4.1 Public Switched Telephone Network
From an application perspective, Internet nodes are interconnected
directly, as shown in Figure 1. When two machines are to communicate,
they will have the address of the destination end system, and will
send network level datagrams, assuming that the underlying
infrastructure will deliver them as required.
_____
__ _____/ \_____
[__] / \
[----]-.-.-.-. Internet .-.
\_____ _______/ |
__ \__./ __ .
[__] / [__] |
[----]-. [----]-.
Key: .-.-. Internet Access Link
Figure 1
Where all nodes are on the same (broadcast) network, there is no need
for intervening routers; they can send and deliver packets to one
another directly. The Internet nodes are responsible for their own
communications requests, and act as peers in the communication
sessions that result.
This contrasts with the situation in the PSTN. There, the end systems
are configured as shown in Figure 2. The end systems tend to be
specific to a particular type of traffic, so that, for example, the
majority of terminals are dedicated to carrying speech traffic
(telephones) or to carrying facsimile data (fax machines). The
terminals all connect to Central Offices (COs) via access lines, and
these COs are interconnected into a network.
/--\
()/\()__
/__\ \ .................................
\ ! ! ! /--\
__ \ [-!-] [-!-] ! ()/\()
\ \ \__[CO ]=========[CO ]==\\ ! ___/__\
[Fax]________[---] [---] \\ [-!-] / __
\\=======[CO ]____/ \ \
[---]________[Fax]
Key: ___ Access Lines
=== Trunk Links (inter-CO user data links)
... Inter-CO signaling network links
CO Central Office (Telephone Exchange)
Figure 2
Communications between the terminals are all "circuit switched", so a
dedicated synchronous data path (or circuit) needs to be placed
between the end terminals for carrying all communications. Arranging
for such a circuit to be made or removed (cleared) is the
responsibility of the Central Offices in the network. A user makes a
request via his or her terminal, and this request is passed on to the
"local" Central Office. The relationship between the terminals and
the local Central Offices to which they are connected is strictly
Client/Server.
The COs are interconnected using two different types of connections.
One of these is called a trunk connection (shown as a double line in
the above figure) and is used to carry the data traffic generated by
the terminals. The other connection acts as part of a separate
network (and is shown as a dotted line in the above figure). This is
the signaling network, and is used by the Central Offices to request
a connection to be made between themselves and the destination of the
required circuit. This will be carried across the trunk link to the
"next" Central Office in the path. The path, once in place through
the PSTN, always takes the same route. This contrasts with the
Internet, where the underlying datagram nature of the infrastructure
means that data packets are carried over different routes, depending
on the combined traffic flows through the network at the time.
The call set up process can be viewed as having two parts: one in
which a request for connection is made, and the other in which the
circuit is made across the PSTN and call data flows between the
communicating parties. This is shown in the next pair of figures (3a
and 3b).
/--\
() ()
--____
/++\ \
/----\ \
A \ [-!-]
\->[CO ]
[---]
Time = 13:55
Figure 3a
Key: ___ Access Lines
=== Trunk Links (inter-CO user data links)
... Inter-CO signaling network links
CO Central Office (Telephone Exchange)
/--\
() ()
-- .................................
/ \<--- ^ ! ! /--\
/----\ \ ! v ! () ()
A' \ [-!-] [-!-] ! --
\__[CO ]=========[CO ]==\\ v ->-/ \
[---] [---] \\ [-!-] / /----\
\\=======[CO ]____/ B'
Time = 14:00 [---]
Figure 3b
Figure 3 shows a particular kind of service that can be provided;
call booking. With this service, a request is sent for a connection
to be made between the A and B telephones at a specified time. The
telephone is then replaced (the request phase is terminated). At the
specified time, the CO will make a connection across the network in
the normal way, but will, first, ring the "local" or A' telephone to
inform the user that his or her call is now about to be made.
For more complex services, the requesting telephone is often
connected via its "local" CO to a Service Node (SN), where the user
can be played prompts and can specify the parameters of his or her
request in a more flexible manner. This is shown below, in Figures
4a and 4b. For more details of the operation of the Service Node (and
other Intelligent Network units), see the Appendix.
When the SN is involved in the request and in the call setup process,
it appears, to the CO, to be another PSTN terminal. As such, the
initial request is routed to the Service Node, which, as an end
system, then makes two independent calls "out" to A' and B'.
/--\ [---]
() () [SN ]
--___ [|--]
/++\ \ |
/----\ \ |
\ |
A \ [|-!]
\->[CO ]
[---]
Time = 13:55
Figure 4a
Key: ___ Access Lines
=== Trunk Links (inter-CO user data links)
... Inter-CO signaling network links
CO Central Office (Telephone Exchange)
SN Service Node
/--\ [---]
() () [SN ]
-- [|--] /--\
/ \<-- | ............................... () ()
/----\ \ | ^ ! ! --
\ | / v v / \
A' \ [|-!] [-!-] [-!-] ->-/----\
\--[CO ] [CO ] [CO ] /
[---] [---] [---]___/ B'
Time = 14:00
Figure 4b
Note that in both cases as shown in Figures 3 and 4 a similar service
can be provided in which the B' telephone is replaced by an
Intelligent Peripheral (or an Special Resource Functional entity
within a Service Node), playing an announcement. This allows a "wake
up" call to be requested, with the Intelligent Peripheral or Service
Node Special Resource playing a suitable message to telephone A' at
the specified time. Again, for more details of the operation of the
Special Resources (and other Intelligent Network units), see the
Appendix.
4.2 Pre-PINT Systems
Although the pre-PINT systems reported here (i.e., those developed by
AT&T, Lucent, Siemens and Nortel) vary in the details of their
operation, they exhibit similarities in the architecture. This
section highlights the common features. Specific descriptions of
these systems will follow.
All of the systems can be seen as being quite similar to that shown
in the following diagram. In each case, the service is separated into
two parts; one for the request and another for execution of the
service. Figure 5 summarizes the process.
_____
__ _____/ \_____
[__] / \
[-++-]-.-.>.-. Internet .-.-
\_____ _______/ .
\___/ v
[----] .
[PINT]-.-
[----]
%
v
[---]
[SN ]
[|--]
Figure 5a
Key: CO Central Office (Telephone Exchange)
SN Service Node
PINT PSTN/Internet Gateway
.-.-. Internet Access Link
%%% Gateway/Service Node Link
___ PSTN Access Lines
=== PSTN Trunk Links (inter-CO user data links)
... Inter-CO signaling network links
_____
__ _____/ \_____
[__] / \
[----]-.-.-.-. Internet .-.-
\_____ _______/ .
\___/ |
[----] .
[PINT]-.-
[-%--]
%
%
/--\ [-%-]
() () [SN ]
-- [|--] /--\
/ \<-- | .................... () ()
/----\ \ | ^ ! ! --
\ | / v v / \
A' \ [|-!] [-!-] [-!-] ->-/----\
\--[CO ]=======[CO ]======[CO ] /
[---] [---] [---]__/ B'
Figure 5b
Comparing Figure 4a with Figure 5a, the differences lie in the way
that the information specifying the request is delivered to the
Service Node. In the PSTN/IN method shown in the earlier diagram, the
user connects to the SN from the telephone labeled A, with the
connection being routed via the CO. In the latter case, the request
is delivered from an Internet node, via the PINT gateway, and thence
to the Service Node over a "private" link. The effect is identical,
in that the request for service is specified (although the actual
parameters used to specify the service required may differ somewhat).
The figures depicting the respective service execution phases
(Figures 4b and 5b) show that the operation, from the IN/PSTN
perspective, is again identical. The Service Node appears to initiate
two independent calls "out" to telephones A' and B'.
The alternative systems developed by AT&T and by Nortel allow another
option to be used in which the PINT Gateway does not have to connect
to the PSTN via a Service Node (or other Intelligent Network
component), but can instead connect directly to Central Offices that
support the actions requested by the gateway. In these alternatives,
the commands are couched at a "lower level", specifying the call
states required for the intended service connection rather than the
service identifier and the addresses involved (leaving the
Intelligent Network components to coordinate the details of the
service call on the gateway's behalf). In this way the vocabulary of
the commands is closer to that used to control Central Offices. The
difference really lies in the language used for the services
specification, and all systems can use the overall architecture
depicted in Figure 5; the only question remains whether the
Intelligent Network components are actually needed in these other
approaches.
The following diagram (Figure 6) shows the interface architecture
involved in providing the kind of service mentioned above.
Internet __ __
Server [__] _______ [__]
[W3S-]-. ___/ .-.-.-[W3C-] Internet
_________________|/.-.-.-.-. \ Terminal
/ .. . \
| Internet / . \ |
\___________ . . . /
\/___|____\_________/
. . .
/ | \
(A) (B) (E)
. . .
_|_ _|_ _|_
[SN ]<-(D)--[SMS]--(H)->[SCP]
[|-|] --- [-!-]
/ \ !
(C) (I) ...........(F)...!.(G).
/ \ ! !
[--|] [|-!] [-!-]
[CO ] [MSC] [SSP]
[---] [---] \|/ [---]
/--\ | |____| | /--\
()/\() | | ()/\()
/--\___| 1 |___/--\
Fixed PSTN Terminal [] Fixed PSTN Terminal
Mobile Terminal
Key: W3S HTTP (Web) Server
W3C HTTP (Web) Client/Browser
CO Central Office (Telephone Exchange)
MSC Mobile Switching Center (Mobile Network Telephone
Exchange)
SN Service Node
SSP Service Switching Point
SCP Service Control Point
SMS Service Management System
.-.-. Internet relationship
___ PSTN Access relationship
... PSTN "core" signaling relationship
Figure 6
The interfaces are:
A The interface over which Internet requests for service are
delivered to the Service Node
B The interface over which Service Management requests are sent
from the Internet to the Service Management System
C The interface over which the Service Node sends call control
requests to a connected Central Office
D The interface over which the Service Management System manages
the Service Node
E The interface over which Internet requests for service are
delivered to the Service Control Point
F The interface over which the Service Control Point sends service
call control requests to the Mobile Switching Center
G The interface over which the Service Control Point sends service
control requests to the Service Switching Point
H The interface over which the Service Management System manages
the Service Control Point
I The interface over which the Service Node sends service call
control requests to the Mobile Switching Center
In practice, a number of the interfaces have very similar purposes to
one another. The means by which these purposes are achieved differ,
in that some of the interfaces (C and I) reflect access arrangements,
whilst others (F and G) imply a "core" signaling relationship.
However, it is possible to categorize them in terms of the "intent"
of messages sent across the interfaces.
For example, Interfaces A and E are similar; one of the main aims of
PINT work is to ensure that they are the same. Similarly, Interfaces
D and H imply similar actions and are likely to carry similar
messages. Interfaces C, F, G, and I are all used to request that a
call be initiated, albeit via access or core signaling relationships.
The interfaces can also be viewed in terms of the kind of components
that are involved and the bodies by which they are codified.
Interfaces A, B, and E are all going to be realized as Internet
Protocols. All of the others use existing protocols in the PSTN/IN.
Traditionally, these have been codified by different groups, and this
is likely to be the case in the PINT work.
The general arrangements for the different systems are shown below
(Figures 7, 8, 9, and 10). They differ in the details of their
configurations, but the main tasks they perform are very similar, and
so the overall operation is similar to the generic architecture shown
in Figures 5 and 6.
Key for following diagrams:
Components:
W3C World Wide Web Client
W3S World Wide Web Server
WSA Web Server "Back End Program" Interface (CGI or Servlet
interface)
Srvlt Servlet "back end" program/objects
FS Finger Server
SCTPC Simple Computer Telephony Protocol Client
SCTPS Simple Computer Telephony Protocol Server
CBC CallBroker Client
CBS CallBroker Server
SSTPC Service Support Transport Protocol Client
SSF Service Switching Function
SCF Service Control Function
SRF Special Resource Function
CO Central Office/ Public Telephone Exchange
SSP Service Switching Point
SCP Service Control Point
SR/I.IP Special Resource/ "Internet" Intelligent Peripheral
SMS Service Management System
INAPAd Intelligent Network Application Part Adaptor
PktFlt Packet Filter (Firewall)
SNMPAg Simple Network Management Protocol Agent
Protocols:
P0 HyperText Transfer Protocol
P1 HTTP Server <-> "Back End Program" internal protocol
P2 CallBroker Client <-> CallBroker Server protocol (AT&T system),
or SCTP Client <-> Server protocol (Nortel system)
P3 PINT User Agent <-> PINT Gateway protocol
P4 Intra-Intelligent Network protocol (e.g., INAP)
P5 Proprietary (INAP-based) Gateway-> I.IP protocol
P6 Finger protocol
P7 Digital Subscriber Signaling 1 protocol
P8 Simple Network Management Protocol
P9 SMS <-> Service Control Point/Service Node protocol
_____ _______ _____
|[W3C]|----(p0)-->| [W3S] |<--(p0)----|[W3C]|
|[---]| | [WSA] | |[FS.]|
|-----| | ! | |[-!-]|
| (p1) | |--\--|
| ! | ^
| ! | (p6)
| ! | \
| (p1) | \
| ! | \
|[Srvlt]| \
|___!___| \
! \
(p3) \
Internet ! !
.+.+.+.+.+.+.+.+.+.+.+. v .+.+.+.+.+.+.+.+.+.+.+.+.+.!.+.+.+.+.+.
PSTN/IN _______________!_________________ ____!_____ __________
|I [PktFlt] I| |[PktFlt]| |[PktFlt]|
|N Gateway N| | ! | | ! |
|A ___________________________ A| | ! | | ! |
|P | | P| | ! | |[SNMPAg]|
-(p4)-- |A | <-(p4)-> [SCP] <-(p4)-> | A|-(p5)->|[SR/IIP]| | [SMS] |
\ |d | [-^-] | d| |[------]| | [-^-] |
\ |__| ! |__| |________| |___!____|
\ ! !
[-v-] !-----------------(p9)-----------------!
[SSP]
[---]
___| |______
| |
| /--\ | /--\
| ()/\() | ()/\()
|__/__\ |____/__\
Figure 7: The Siemens Web Call Center
_____ _______
|[W3C]|----(p0)-->| [W3S] |
|[---]| | [WSA] |
|-----| | ! |
| (p1) |
| ! |
| ! |
| ! |
| (p1) |
| ! |
|[SSTPC]|-<----------------------------------
|___!___| !
! (p8)
(p3) !
Internet ! v
.+.+.+.+.+.+.+.+.+.+.+. v .+.+.+.+.+.+.+.+.+.+.+.+.+.+.+.+.+.+. ! .+.+
PSTN/IN _______________!__________________________________ ____!_____
| [PktFlt] Service [PktFlt]| |[PktFlt]|
| ! Node | | ! |
| [SCF Adaptor] | | ! |
| ! | |[SNMPAg]|
|[SSF]<-(p4)->[SCF] <-------(p4)--------> [SRF] | | [SMS] |
|[|--] [-^-] [---] | | [-^-] |
|_|_____________!________________________________| |___!____|
| ! !
[-v-] (p7) !-----------------(p9)-----------------!
[CO.]____|
[---]
___| |_______
| |
| /--\ | /--\
| ()/\() | ()/\()
|__/__\ |____/__\
Figure 8: The Lucent System
_____ ________
|[W3C]|----(p0)-->| [W3S] |
|[---]| | [WSA] |
|-----| | ! |
| (p1) |
| ! |
|[WS/CBS]|
|[Adaptr]|
|___!____|
^
(p2)
_____ ___v____
|[CBC]| | [CBS] |
|[---]|<---(p2)-->| [---] |-<---------------------------------
|-----| |___!____| !
! (p8)
(p3) !
Internet ! v
.+.+.+.+.+.+.+.+.+.+.+. v .+.+.+.+.+.+.+.+.+.+.+.+.+.+.+.+.+.+. ! .+.+
PSTN/IN _______________!__________________________________ ____!_____
| [PktFlt] Service [PktFlt]| |[PktFlt]|
| ! Node | | ! |
| [SCF Adaptor] | | ! |
| ! | |[SNMPAg]|
|[SSF]<-(p4)->[SCF] <-------(p4)--------> [SRF] | | [SMS] |
|[|--] [-^-] [---] | | [-^-] |
|_|_____________!________________________________| |___!____|
| ! !
[---] (p7) !-----------------(p9)-----------------!
[CO.]____|
[---]
___| |_______
| |
| /--\ | /--\
| ()/\() | ()/\()
|__/__\ |____/__\
Figure 9: The AT&T System
_____ ________
|[W3C]|----(p0)-->| [W3S] |
|[---]| | [WSA] |
|-----| | ! |
| (p1) |
| ! |
|[WS/ ]|
|[ SCTPS]|
|[Adaptr]|
|___!____|
^
(p2)
_______ ___v___
|[SCTPC]| |[SCTPS]|
|[-----]| <-(p2)--> |[-----]|-<----------------------------------
|-------| |___!___| !
! (p8)
(p3) !
Internet ! v
.+.+.+.+.+.+.+.+.+.+.+. v .+.+.+.+.+.+.+.+.+.+.+.+.+.+.+.+.+.+. ! .+.+.
PSTN/IN _______________!__________________________________ ____!_____
| [PktFlt] Service [PktFlt]| |[PktFlt]|
| ! Node | | ! |
| [SCF Adaptor] | | ! |
| ! | |[SNMPAg]|
|[SSF]<-(p4)->[SCF] <-------(p4)--------> [SRF] | | [SMS] |
|[|--] [-^-] [---] | | [-^-] |
|_|_____________!________________________________| |___!____|
| ! !
[---] (p7) !-----------------(p9)-----------------!
[CO.]____|
[---]
___| |_______
| |
| /--\ | /--\
| ()/\() | ()/\()
|__/__\ |____/__\
Figure 10: The Nortel System
As these are independent systems developed by different groups, the
names of the components, unsurprisingly, don't match. Some features
are offered by one of the systems, while they aren't by others.
However, there are a number of common features. All of the systems
provide a Web-based interface (at least as an option), using "back
end" programs to construct protocols to pass onwards to the
Intelligent Network system.
Several Intelligent Network Functional Entities are combined into a
Service Node in the Lucent, AT&T , and Nortel systems, while in the
Siemens scheme they are separate units. However, this is not
particularly important for the provision of the services they offer.
The main difference lies in whether or not the SCF is "aware" of the
Internet interface and has been modified to be "complicit" in
supporting these Internet requests. The Siemens approach was to re-
use an existing SCP, providing a gateway function to translate as
needed. The Lucent system used a "lighter weight" SCF adapter to
terminate the Internet protocols, as the SCF was modified to support
the Internet interface directly.
The AT&T CallBroker and Nortel SCTP Servers introduce an intermediate
protocol (labeled p2) that allows an alternative to the Web based
interface supported by the others. This protocol matches the
"CallBroker Client API", or the "SCTP Client API". These options
provide for a bi-directional protocol, with indications sent from the
Call Broker or SCTP Server to the Client as needed. This is not
easily possible using an HTTP-based scheme (and in the Siemens case,
a dedicated Finger client/server pair was used to emulate such an
interface)
The protocol between the Internet server and the Intelligent Network
(labeled p3 in the above diagrams) differs in each of the systems.
One of the main aims of future work will be to develop a common
protocol that will support the services offered, so that the p3
interface will allow different implementations to inter-operate. In
the Lucent, Siemens, and Nortel systems, this was an "internal"
protocol, as it was carried between entities within the Service Node
or Gateway.
Other contrasts between the systems lie in the support for Internet
access to Service Management, and access to the Internet by Special
Resources. Internet Management access was most developed in the
Lucent system, in which a Simple Network Management Protocol (SNMP)
agent was provided to allow inter-operation with the SMS controlling
the Service Node. In the Siemens scheme, the SMS had no direct
Internet access; any management actions were carried out within the
normal PSTN management activities. As for Internet access to special
resources, this was only required by the Siemens system as part of
its support for Call Center agent notification. Equivalent
functionality would be provided in the AT&T and Nortel systems as
mentioned above, and this would in turn be associated with event
notifications being sent as part of their (p3) Internet/IN protocol.
These differences reflect the different emphases in the products as
they were developed; again, future work will have to ensure that
common protocols can be used to support the chosen services fully.
5. IN-Based Solutions
5.1 The Lucent System
Figure 11 depicts the overall interconnection architecture of the
Lucent prototype in support of the four PINT services. The IN-based
architecture utilizes the Service Node and Service Management System
in addition to the Web server, which enables Web-based access to the
PINT services. This section summarizes the roles of these elements
(complemented by a click-to-dial-back service scenario), outlines the
interfaces of Web Server-Service Node and Web Server-Service
Management System (i.e., the interfaces A & B), and addresses the
common security concerns.
5.1.1 Roles of the Web Server, Service Node, and Service Management
System
Web Server
The Web Server stores the profiles of content providers as well as
pre-registered users. The content provider profile contains
information such as content provider ID, telephone number, and fax
number. In addition, the profile may also include service logic that
specifies, for example, the telephone (or fax) number to be reached
based on time of the day, day of the week, or geographical location
of the user, and the conditions to accept the charge of the calls.
Similar to the content provider profile, the pre-registered user
profile contains information such as user name, password, telephone
number, and fax number. The last two pieces of information can also
be linked to time of the day and day of the week so the user can be
reached at the appropriate telephone (or fax) number accordingly.
Service Node
Situated in the PSTN, the SN, like the SCP, performs the service
control function [1, 2, 3]. It executes service logic and instructs
switches on how to complete a call. The SN also performs certain
switching functions (like bridging of calls) as well as a set of
specialized functions (like playing announcements, voice recognition
and text-to-speech conversion).
Service Management System
The SMS performs administration and management of service logic and
customer-related data on the SN. It is responsible for the
replication of content provider profiles and provision of these data
on the SN. These functions are non-real time.
Web Users
____________
O -------------------------- | Internet |-------------------
------------ |
|
|
---------------- -------------- ------------
| Service Node | D | Service | B |Web Server|
| (SN) |------------| Management |---------------| |
| | |System (SMS)| | |
| | A -------------- | |
| |-----------------------------------------| |
---------------- ------------
| |
| I | C
| |
----------- ---------
|Mobile | |Central|
|Switching| |Office |
| Center | ---------
----------- |
| |
| |
O O
Mobile Wireline PSTN
Users Users
Figure 11: Overall Interconnection Architecture of the Lucent System
5.1.2 A Click-to-Dial-Back Service Scenario
A Web user, who has simultaneous access to the Web and telephone
services (this can be achieved, for example, by having an ISDN
connection), is browsing through a sales catalogue and deciding to
speak to a sales representative.
When the Web user clicks a button inviting a telephone call from the
sales office, the Web Server sends a message to the SN over the A
interface, thus crossing the Internet-to-PSTN boundary. By matching
the information received from the Web Server with the content
provider profile that had been previously loaded and activated by the
SMS over the D interface, the SN recognizes the signal.
At this point, the SN calls the Web user. The user answers the call,
hears an announcement, e.g., "Please wait, while we are connecting
you to the sale agent", and is waiting to be connected to the sale
agent. Then the SN invokes service logic as indicated in the profile.
The execution of this logic selects an appropriate sales agent to
call based on the time of the day. It is 8 P.M. in New York where
the Web user is located, and the New York sales office has closed.
The San Francisco office, however, is still open, and so the SN makes
a call to an agent in that office. Finally, the SN bridges the two
calls and establishes a two-party call between the sales agent and
the Web user.
5.1.3 Web Server-Service Node Interface
Lucent developed the Service Support Transfer Protocol (SSTP) for
communications between the SN and Web Server. SSTP is of a
request/response type running on top of a reliable transport layer,
such as TCP. The Web Server sends a request to the SN to invoke a
service and the SN responds with a message indicating either success
or failure. Note that SSTP engages only the service control function
[1, 2, 3] of the SN.
5.1.3.1 Web Server to Service Node
In this direction, three kinds of messages may be sent: the
Transaction Initiator message, the Data Message, and the End of Data
message.
The latter two messages are needed if the service to be invoked
involves data (such as the case in click-to-fax, click-to-fax-back
and voice-access-to-content). This was so designed to handle the
varying size of data and to ensure that the size of each stream is
within the allowable size of the underlying transport packet data
unit (imposed by some implementations of TCP/IP).
a. Transaction Initiator
This message provides all the necessary information but data for
invoking a service. It includes the following information elements:
+ Transaction ID, which uniquely specifies a service request. The
same transaction ID should be used for all the accompanying data-
related messages, if the service request involves data. One way for
generating unique transaction IDs is to concatenate the information:
date, time, Web Server ID (uniquely assigned for each one connected
to the SN), and transaction sequence number (a cyclic counter
incremented for each service request).
+ Service ID, which specifies the service to be invoked. The service
may be click-to-dial-back, click-to-fax, click-to-fax-back or voice-
access-to-content.
+ Content Provider ID, which uniquely represents the content
provider. This information is the key to accessing the content
provider's service logic and data on the SN.
+ Content Provider Directory Number, which is the telephone or fax
number of the content provider to be called through the PSTN.
+ User Directory Number, which is the telephone or fax number of the
user requesting the service.
+ Billed Party, which specifies the party (either the user or content
provider), to be billed.
In addition, optional parameters may be sent from the Web Server to
the SN. For example, a retry parameter may be sent to specify the
number of times the SN will attempt to complete a service request
upon failure before the transport connection times out.
b. Data Message
This message provides the (encapsulated) user data part of a service
request. For example, in the case of click-to-fax-back such data are
the content to be faxed to the user. Each message is composed of the
transaction ID and a data segment. The transaction ID must be the
same as that of the transaction initiator part first invoking the
service.
c. End of Data Message
This message contains the transaction ID and the end of data
delimiter. The transaction ID is the same as that of the relevant
transaction initiator message.
5.1.3.2 Service Node to Web Server
The SN must respond to a service request from the Web Server. The
response message consists of the information elements:
transaction ID, service type, result, time, and error code.
+ Transaction ID, which is the same as that of the original service
request.
+ Service Type, which is the same as that of the original service
request.
+ Result, which is either success or failure.
+ Time, which indicates the time of the day completing the request.
+ Error Code, which gives the reason for failure. Possible reasons
for failure are content provider telephone (or fax) busy, content
provider telephone (or fax) no answer, user telephone busy, user
refusal to complete, user no answer, nuisance control limit reached,
and content provider telephone (or fax) not in the SN database.
5.1.3.3 Usage Scenarios: Click-to-Fax and Click-to-Fax-Back
For the click-to-fax and click-to-fax-back services, the Lucent
system implemented only the case where the data to be sent as
facsimile reside in the Web server. There are at least three messages
that need to be sent from the Web server to the Service Node for
these services.
The first message is the Transaction Initiator that identifies the
service type as well as a unique Transaction ID. It also includes the
sender/receiver fax number.
The next is one or more messages of the data to be faxed. Each
message carries the same unique Transaction ID as the above.
Last comes the end of message. It consists of the Transaction ID
(again, the same as that of the messages preceding it) and the end of
data delimiter.
Upon receiving these messages, the Service Node, equipped with the
special resource of a fax card, converts the data into the G3 format,
calls the receiver fax, and sends back the result to the Web server
immediately. Note that the receiver fax busy or no answer is
interpreted as failure. Further, while the receiver fax answering the
call is interpreted as success, it does not necessarily mean that the
fax would go through successfully.
5.1.4 Web Server-SMS Interface and SNMP MIB
This interface is responsible for uploading the content provider
profile from the Web Server to the SMS and for managing the
information against any possible corruption. The SN verifies the
Content Provider ID and the Content Provider Directory Number sent by
the Web Server with the content provider profile pre-loaded from the
SMS.
The content provider profile was based on ASN.1 [4] structure and
SNMP [5] was used to set/get the object identifiers in the SMS
database.
Following is an example of the simple MIB available on the SMS.
inwebContProviderTable OBJECT-TYPE
SYNTAX SEQUENCE OF InwebContProviderEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
" A table containing Content Provider profiles "
:= { inweb 1}
inwebContProviderEntry OBJECT-TYPE
SYNTAX InwebContProviderEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
" A conceptual row of the inweb. Each row
contains profile of one Content Provider"
INDEX { inwebSmsNumber }
:= { inwebContProviderTable 1 }
InwebContProviderEntry := SEQUENCE {
inwebSmsNumber Integer32,
inwebContentProviderId Integer32,
inwebContentProviderPhoneNumber Integer32,
inwebContentProviderFaxNumber Integer32
}
inwebSmsNumber OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
" Serial number of the SMS - used for SNMP indexing "
:= { inwebContProviderEntry 1 }
inwebContentProviderId OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
" A number that uniquely identifies each Content
Provider "
:= { inwebContProviderEntry 2 }
inwebContentProviderPhoneNumber OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
" Content Provider's Phone Number "
:= { inwebContProviderEntry 3 }
inwebContentProviderFaxNumber OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
" Content Provider's Fax Number "
:= { inwebContProviderEntry 4 }
5.1.5 Security Considerations
The Lucent prototype addressed the security issues concerning the
interface between the Web Server and the SN. Those concerning the
interface between the Web Server and SMS, which was based in SNMP,
were handled by the built-in security features of SNMP.
+ Secure Communication Links
If the Network Operator (PSTN provider) is also the Web Service
provider, the Web Server and SN/SMS will communicate over a corporate
intranet. This network is almost always protected by the
corporation's firewall and so can be deemed secure. This was the case
handled by the Lucent prototype.
Nevertheless, if different corporations serve as the Network Operator
and the Web Service Provider, then it is likely that there may not
exist a dedicated secure communication link between the Web Server
and SN/SMS. This raises serious security considerations. One possible
solution is to use Virtual Private Networks (VPN). VPN features
support authentication of the calling and called parties and
encryption of the messages sent over insecure links (such as those on
the Internet).
+ Non-Repudiation
All transactions were logged on both the Web Server and the Service
Node to account for all operations in case of doubt or dispute. The
log information on the SN may also be used to generate bills.
+ Malicious Requests of Users
A user may make repeated requests to a content provider directory
number maliciously. This scenario was handled by setting a Nuisance
Control Limit (NCL) on either the SN or the Web Server or both. The
NCL has two parameters: one defining the number of requests from a
user and the other the period over which these requests takes place.
A user may also attempt to request a call from a directory number
other than that of a content provider. This scenario was handled by
verifying the directory number (and the content provider ID) against
the database on the SN containing all the content provider
information. If the directory number (or the content provider ID) was
not in the database, the request would be rejected.
5.2 Siemens Web Call Center
5.2.1 Service Description
The Web Call Center is an Intelligent Network System that accepts
requests from Internet nodes for services to be provided on the PSTN.
As the name suggests, it was designed to support a cluster of
services that, taken together, provide a subset of the features of a
Call Center, with almost all user interactions provided via World
Wide Web requests and responses. See the appendix for a background
description of Call Center Features.
From an Intelligent Network perspective, there are a number of
services that, when combined, provide the Call Center features. The
Call Center features as implemented supported the scenario in which a
customer makes a request to be called back by an agent at a time of
the customer's choosing to discuss an item of interest to him or her.
The agent will be selected based on his or her availability and
expertise in this topic; the agent will be told whom he or she is
calling and the topic of interest, and then the agent will be
connected to the customer.
In addition, the individual services that were deployed to support
this scenario provided support for management of the list of
available agents as well. This involved allowing the agent to "log
into" and "out of" the system and to indicate whether the agent was
then ready to handle calls to the customer. The list of services, as
seen from a user perspective, follows.
The services support:
i) Customer Request service - the customer explores a corporate Web
site, selects a link that offers to request an agent to call the
customer back and then is redirected to the Web Call Center server.
This presents customer with a form asking for name, the telephone
number at which he or she wishes to be called, and the time at which
the call is to be made. Note will also be made of the page to which
the customer was referred to when he or she was redirected. Once the
form has been returned, the customer receives an acknowledgment page
listing the parameters he or she has entered.
ii) Agent Registration/Logon - An agent requests a "login" page on
the Web Call Center server. The service checks whether it has a
record of an agent present at the Internet node from which th call is
made. If not, then the caller will be sent a form allowing him or her
to enter the service identity, the company's agent identifier and
password. On return, the service identity and company agent
identifier will be checked against a list of known identities. If
found, the password will be checked, and if this matches the record
held by the service then a new session record is made of this
identity and the Internet node from which the call has been made.
NB: This is very similar to the Universal Personal Telecommunications
(UPT) service feature "register for incoming calls". It implies that
the identified person has exclusive use of the Internet node from
that point onwards, so messages for them can be directed there.
iii) Agent Ready - an agent who has already logged on can indicate
that he or she is ready by requesting an appropriate "ready" page on
the Web Call Center Server. The service will match the agent by the
Internet node Identifier and Agent Identity passed along with the Web
request against its list of "active" agents. It will mark them as
being ready to handle calls in its list of available agents (with
their pre-defined skill set).
iv) Agent Not Ready - an agent can request an appropriate "ready"
page on the Web Call Center Server to indicate that he or she is
temporarily not ready to handle calls.
v) Agent Logoff - an agent can request an appropriate "Logout" page
on the Web Call Center Server to indicate that he or she is no longer
associated with a particular Internet node. The service will match
the agent by the Internet Node Identifier and Agent Identity passed
along with the Web request against its list of "active" agents. Once
found, the session record for that agent is removed and the caller is
notified of this with an acknowledgment page.
NB: This is very similar to the UPT "unregister" service feature.
vi) Call Center Agent Selection and Notification - When the time
that the customer selected has arrived and an available agent with
the right skills has been selected from the appropriate list, this
service will send a notification to the Internet node associated with
that agent. A dedicated server is assumed to be running on the
agent's machine that, on receiving the notification, triggers the
agent's browser into requesting a "Agent Call In" page from the Web
Call Center Server. Once the agent's machine has made this request,
he or she will be told that there is a customer to call.
NB: This is similar to a "Message Waiting" or "Wake Up Call" service.
Note: As implemented, the agent is led automatically into the
following service (the returned Web page includes an automatic reload
command).
vii) Agent Instruction - a selected agent makes a request of the
"Customer Processing" page on the Web Call Center Server. The
Internet node Identifier and Agent Identity the agent uses will be
matched against a list of agents expected to handle calls, and the
instructions for the calls will be returned to the agent.
NB: This is similar to a "Voice Mail Replay" message service, but in
this case the message is automatically generated; there is no
associated voice mail record feature accessible.
Note: As implemented, the instructions page will include a number of
buttons, allowing the agent to view the page the customer was looking
at when he or she made the request, and to trigger the customer
callback (as described next).
ix) Agent/Customer Telephony Callback - the agent will make a
request of a "dial-back" page on the Web Call Center Server. The
Internet node Identifier and Agent Identity he or she uses will be
matched against a list of agents expected to handle calls, and, when
the appropriate records have been found, the service will make the
telephone call through to the customer and then connect the agent to
this telephone call (using the telephone number registered in the
respective Call Center service record).
5.2.2 Implementation
5.2.2.1 Introduction
The Siemens Web Call Center used an existing IN system and service
logic that supported Call Center features. The scenario it supports
is very similar to the Siemens IN-based Call Center on which it was
based; one of the goals was to minimize changes to the service
offered. It is also virtually identical to the service "Internet
Requested Telephony Dial-back" provided by the Lucent system.
As provided via the Internet, the services involved are mostly the
same as those provided via the PSTN and IN alone. The main
differences lie in the use of the World Wide Web as an interface to
the services rather than a telephone, SSP, and Intelligent
Peripheral. Also, the feature by which a telephone call is made
between the agent and the customer is implemented within the IN
system in a different way; this is the only element in which the PSTN
is involved.
5.2.2.2 Web Call Center Configuration
The general arrangement for the Web Call Center system is shown in
Figure 7. The components that were added to an existing IN system to
deal with the Internet interface are described next.
In addition to the SCP, SSP and SMS that were part of the original
IN-based system, another unit was included to send notification
messages to agents; in the IN system the agents were sent "wake up"
telephone calls when they were required to handle their next
customers' call back. This unit is called the "Internet Intelligent
Peripheral", and its use is described later under "Non-World Wide Web
Interactions".
As there was a need to re-use as many of the existing IN components
unchanged, a Gateway unit to deal with the interface between the
Internet and the SCP was provided. This injected INAP (Intelligent
Network Application Protocol) messages into the SCP, making it think
that it had received an Initial DP trigger from an SSP. It also
intercepted the "Connect To Resource" and "Prompt and Collect" INAP
messages sent from the SCP, acting on these to return the parameters
generated by the Internet users when they filled in the forms that
triggered the service transaction. It also translated the "Play
Announcement" message sent to the Intelligent Peripheral into a form
that it could use. Finally, it passed on the INAP message used by
the SCP to trigger SSP into making the telephone call back.
5.2.2.3 User Interaction
In the IN/PSTN-based system, the services have contact with the
customers and agents via their telephones, SSPs, and Intelligent
Peripherals programmed to play announcements to them and to capture
their responses. These responses are indicated by DTMF tones sent by
pressing keys on the telephones.
In this case, almost all interactions are provided via World Wide Web
requests and responses. The sequence of announcements and responses
for each service are "collapsed" into individual form filling
transactions, and the requests are not limited to digits (or "star"
and "hash"). The implications of the use of forms on service
operation are covered in more detail later (under HTTP/IN Service
mapping).
5.2.2.4 Service/Caller Identifiers
When provided via the IN/PSTN-based system, the services are passed
the Calling Line Identity (CLI) of the caller and the number the
caller dials (the DN). The CLI value is used extensively to identify
the caller and (in the case of the agent) to index into service data
tables to decide what to do next. While an equivalent value to the
DN is passed to the Web-based transactions as the requested Universal
Resource Locator (URL), the CLI cannot be given reliably. The nearest
equivalent caller identifier is the IP Address of the customer or
agent's machine. However, the use of HTTP proxies means that this
"original" Internet node Address may not be available; if a proxy is
used then its IP Address will be associated with the request.
In providing these Call Center features the customer only has one
Web-based transaction; that of providing the initial request for a
PSTN telephone callback. To do so he or she will have to fill in a
form so as to specify not only the time to be called back, but also
the telephone number to be reached. These values can be used if
needed to identify the customer, and so the problem of originating
Internet Node ambiguity is not relevant.
With the agents, however, there are sequences of coupled
transactions, and the particular sequence must be identified. There
will be a number of such transactions being carried out at once, and
there needs to be some identifier to show which agent is being
handled in each case.
Such an identifier is not part of a sequence of basic Web
transactions. In a Web transaction, the HTTP Client/Web Browser makes
a request, and the HTTP Server will respond to this, normally
including some content in its reply message that will be processed by
the browser, after which it closes the TCP connection. That's the end
of the transaction; the HTTP client and server cannot normally
maintain state information beyond this point. Any sequence is reduced
to a set of unrelated transactions.
A result of this simple pattern is that any state information
reflecting longer or more complex interactions must be stored (at
least partially) in the client system. One approach is the use of
cookies [6]. These can be set by HTTP servers as part of their
response to a request, and will be sent back with all subsequent
requests for appropriate URLs as extra HTTP headers. These cookies
allow the HTTP server to identify the client in the following
requests, so that it can continue an extended session with the
client.
Cookies are used in providing the Internet Call Center. Persistent
cookies are installed into the Web Browser on machines that are to be
used by call center agents as a service management (pre-service)
task. The cookie value is unique to the machine and is used to index
into a list of machine IP addresses that is stored as part of the
service data.
Also, a session cookie is stored onto the agent's machine when the
agent registers, and is cleared when he or she de-registers. This is
used to identify the agent and so the IP address of the node with
which the agent is associated (and from which the agent's subsequent
requests should originate). The services that interact with Call
Center agents use the agent session cookie value as an identifier; in
principle this is unnecessary but it does simplify the session data
lookup procedure. The rest of the services use the persistent machine
identifier in place of the CLI, indexing into their service data
using it. Both cookies are sent with each agent request; if they are
not present, then the request is redirected to other services (for
example to the agent Logon service).
5.2.2.5 Mapping from HTTP Transactions to IN-Based Service Features
All of the client-initiated services require user interaction. With
the IN/PSTN-based system, the majority of the services are typified
by the callers being connected to an announcement unit that plays
them a list of choices and captures their selection. The caller can
pre-dial the digits needed; in this case the prompts are not needed
and are not made.
The pattern of operation is somewhat different in the Internet case,
as the initial HTTP request returns a response, after which the Web
transaction has ended. Where that initial response returns a form to
be filled in by the caller, subsequently submitting the form
initiates a new HTTP transaction. This is all part of one instance
of service, however. The service consists of two request/response
pairs in tandem.
Although it is possible to design a service to handle this pair of
Web transactions as a single unit, it may be better to reconfigure
it. The design of a service that deals with two Web exchanges as a
single extended transaction is quite complex. It must maintain state
across the pair of Web exchanges, and it has to handle a number of
failure cases including dealing with time-outs and "out of time"
submission of forms. The alternative is to split the service into two
sub-features. The first of these reflects the initial request and
delivery of the form by return, with the second one dealing with
processing of the submitted form and returning any confirmation by
reply.
The services offered don't all require form-filling, and so can be
treated as a single IN feature. There are two cases where forms are
required. The first of these is the Customer Request service, while
the other one is the "Agent Registration" service. In both cases the
initial Web transaction (by which the form is requested and returned
to the client) need not involve specific service logic processing;
the initial delivery of the form to a customer or agent can be
handled by a "normal" Web Server. In both cases the service logic is
only triggered when the form is submitted; this means that, again,
each of the services can be treated as a single IN feature.
The IN service logic that deals with these requests has a general
pattern of action. An HTTP request is received, and this triggers the
IN service logic into action. The service logic "sees" this as an
Initial DP message and starts its processing as if it had been sent
from an SSF. The SCF uses what appears to it to be an Intelligent
Peripheral to collect the parameters of the request, and then to send
back final announcements to the requesting entity.
The main difference, from the perspective of the IN service logic
running on the SCF, is that the service does not need to instruct the
SSF to make a temporary connection to the Intelligent Peripheral. It
is as if this connection had already been made. Similarly, there is
no need to close the service transaction by sending an explicit
"Continue Execution" message to the SSF.
The sequence of "prompt/collect" instructions used to collect service
parameters from a caller in an IN service maps quite well to a
sequence of requests to extract a data value from the HTTP request,
based on a tag. This is a fairly standard feature of Web Server CGI
or Servlet processing. Using this mapping minimizes the changes to
the service design, in that the service logic "sees" an Intelligent
Peripheral to which it sends normal "Request Report Prompt & Collect"
messages, and from which it receives data values in response.
All services have to fit in with the underlying HTTP interaction
pattern, and so will be expected to send a final "Announce"
instruction to the Intelligent Peripheral at the end of the service;
this is done in many IN services anyway and in all of the service
features described here. These announcements form the content
returned to the Web Client.
5.2.2.6 Non-World Wide Web Interactions
There are two exceptions to the sole use of the World Wide Web for
interaction. The first one occurs in the "Message Waiting"/"Wake Up
Call" service by which the selected agent is informed of a callback
request. World Wide Web transactions are very simple; the client
browser makes a request for content associated with a particular HTTP
URL, and the server sends a response, marking the end of the
transaction. The server cannot make a spontaneous association with a
client; it must be initiated by the client request.
While it would be possible for the server to defer closing an earlier
transaction (by not sending back all of the content specified and
leaving the TCP connection open) it was decided that an alternative
scheme would be more convenient. The "wake up call" was arranged by
an "Internet Intelligent Peripheral" sending a request to a daemon
process running on the selected agent's machine, using the Finger
protocol [7]. The daemon sent back a standard response, but in
addition the Web Browser on the agent's machine was triggered into
making a further HTTP request of the server. In this way the "Agent
Instruction" transaction is started automatically, while still
allowing it to use a normal HTTP request/response pattern.
The second exception occurs in the final "Agent/Customer Telephony
Callback" service. While this transaction is initiated by the agent
selecting a link on the "call instructions page" returned to them,
and includes a "confirmation" page being sent back to them in an HTTP
response, the purpose of this service is to make a telephone
connection via the PSTN between the agent's telephone and the
customer's telephone. It is the only service element that involves
the PSTN directly. From an IN/PSTN perspective, the resulting
telephone connection is different from that provided in the scheme
using the IN and PSTN alone. In this case, a PSTN call is made out to
the agent's telephone, another call is made out to the customer's
telephone, and these calls are bridged. This differs from the earlier
scheme, in which the agent originated a call to the voice mail replay
system, and this call was redirected to a new destination (the
customer's telephone). As this feature differs in purpose from the
other services, and it requires a different implementation within the
IN and PSTN system, it was organized as a separate service in this
case.
5.2.2.7 Security Considerations
In the case of this system, assumptions were made that the interface
presented to requesting agents and customers was provided via a fire
wall to deal with most attacks on the IN components. The interface
appeared as a Web Server, and there was no direct access to the HTTP
documents served, nor to the servlets providing the service logic.
The Callback service was deemed to have simpler security requirements
than other IN services as it was akin to a free phone "1-800" service
access number; the agents work for the service subscriber and are not
charged directly. Similarly, the requesting customer is not charged
for his or her request, nor for the resulting call back. Service
subscribers would be willing to pay the costs of telephone calls
generated as a result of this cluster of services, and the costs of
running the agent services could be charged directly to them. As such
the authorization for service is defined by the contract between the
service subscriber and the service provider.
Authentication of agents was seen as a problem. As an interim
measure, cookies were used, but this scheme delivers the cookie data
as a plain text item (a header of the Web request). Secure Socket
Layer connections were required for communication with the agent
services, and this had an impact on the performance of the IN system.
5.2.3 Derived Requirements/Lessons
Security is seen as a major issue. A firewall was used to control
access to the IN Components. Similarly, SSL was used for
communication with the Agents, so as to protect the cookie values
that they were sending with their requests.
For other services, it is likely that the entity from which requests
appear to originate will be charged for the service to be rendered.
This has implications in terms of authentication and authorization of
service provision at the time of the request. It is necessary for the
service to be authorized in such a way that non-repudiation is
ensured; this is likely to mean that a certificate of identity be
provided from the person making the request, and that this can be
tied in with a financial account that that person has with the
service provider. The certificate can then be stored as part of the
billing record. While the process of electronic commerce is outside
of the scope of this work, the mechanism by which a request for
confirmation of identity is passed out to the requesting user and is
delivered back to the service logic must be considered.
When changing from a "pure" IN/PSTN system to one supporting requests
via the Internet, the differences in the way that clients interacted
with the services meant that the service logic had to be redesigned.
It was realized that maintaining the state of a service during its
processing was going to be a problem; this problem was side-stepped
by re-engineering the services as form processors, allowing them to
deal with fully specified requests as a single (Web) transaction. In
addition, a "normal" Web Server was used to deliver the forms to the
users. This is a change from the IN system, where the equivalent of
the form (the prompts) were sent in sequence as part of the same
service process.
The Call Center features provided suited this change. However, this
may not be the case for other IN services. It is quite common for
services to be designed such that the user is prompted for a
response, and the service continues dependent on this response. The
Web form presents all of the options at once, so this kind of variant
prompt/collect sequence is not possible. From this, it is difficult
to see how an IN service could be reused without some degree of
modification.
An intermediate "gateway" system was provided to "cocoon" the service
logic as far as possible from the details of the components with
which it was working. Where needed, this unit translated calls from
the service logic into commands that operated with the Internet (and
the Web Server that acted as the interface). Our experience was that
an SCP could be "spoofed" into thinking that it was operating with
other IN components in the normal way. Within the limits of the
service used, this proved simpler than was originally expected.
Selecting this simple approach still allows a considerable range of
services to be provided while maintaining any investment in existing
IN systems. Modification of existing IN service logic was also
easier than feared. All of the services examined provided
announcements at the end of the service transaction, and this could
be used to trigger a Web response to be sent back to the requesting
Internet user. The changes to the Call Center service logic turned
out to be minor; it took as long to analyze the service and see how
it could be arranged as a sequence of "form processing" transactions
as it did to make the changes to the service logic.
In the Siemens Web Call Center, the "Internet Intelligent Peripheral"
with which the service logic communicated was running as a separate
program on the same node. Where more complex behavior is required of
it (such as conversion of text to speech data and interface with the
PSTN) then it would almost certainly be on a separate node. If data
is transferred from the Internet in such a scheme, any intermediate
gateway would be involved in relaying the data to this node.
6. Alternative Solutions
6.1 The AT&T System
AT&T developed a framework for controlling voice and voice-band data
(e.g., fax) and for providing PINT services. Key to the framework is
CallBroker, a logical entity that acts on behalf of a user to set up
sessions and make requests for PSTN resources. The sessions typically
include initiation of calls between two or more end points specified
by the user. In addition to its interactions with the PSTN for call
setup, the CallBroker is responsible for other functions, when
necessary, such as authentication and usage recording.
This section briefly discusses the protocol at the two interfaces
that need to be defined and the corresponding APIs to provide the
above services. The two interfaces are (1) the one between the
CallBroker (or Web Server) and the Service Control Function in the
Service Node in the PSTN and (2) the one between the IP client and
the CallBroker. The latter interface, in particular, will enable
service providers to extend the architecture defined here to serve as
a platform for other advanced/value-added services (to be identified
later). In addition, the view taken here is that the IP client is
more general, and implements a protocol for communication with the
CallBroker that allows full two-way communications. For example, this
is required for the cases where a called party hangs up and an
indication may be necessary to be given to the IP Client about this
status/progress. This is also necessary when conferencing to give an
indication/status of various parties joining the call.
6.1.1 High Level Architecture
A high level architecture depicting various logical entities and the
Interfaces among these logical Entities and the IP Client is shown in
Figure 12.
________________
/
1 _____ / 2 _____
/|________________| |________| | PSTN
|____| \ |____|
Call \ / SCF\
Broker \ / SN \
\_____________
/ \
/ \
/ \
__ __
/\ /\
Calling Participant
Party (Called Party)
Figure 12: The CallBroker Architecture
The CallBroker, in addition to the initiation and control of calls on
behalf of the user, performs additional functions. These functions
include authenticating the IP Client, usage recording, and management
of the session for the IP Client for the telephony call. The notion
of the session requires that a client state machine be maintained in
the CallBroker. This also helps in notifying the IP Client about the
status/progress of the requests generated from the IP Client.
From the perspective of the IP Client, the logical entities needed
for the above functions are within the CallBroker and are as shown in
Figure 13 below. These correspond to the functions already
discussed: Usage Recording Function, Session Management Function,
Voice Bridge, and the Authentication Function. The fact that some of
these functions may be physically separate from the CallBroker (such
as the Voice Bridge being in the PSTN) is not inconsistent with the
general view adopted here. Thus, the CallBroker Model mediates
requests for network services and enables us to define various value
added services in the future.
llllllllllllllll
l l
l Call Broker l Authentication
l Server l Function
l ______ l Interface 2a ______
l | |x x xlx x x x x x x x x | |
l |______|x l |____|
l x x l
l x xl Interface 2b
lSession State lx
l Mnmgt. x l x Usage Recording
l Function l x Function
l _______ x l x ______
l | | l x x x | |
l |_____| xl |____|
llllllllllllllll
x
x Interface 2c
x
_______
| |
|_____|
Bridge
Figure 13: Functional Entities in the Call Broker
Various interfaces (i.e., 2a, 2b, 2c in Figure 13) between different
functional entities in the CallBroker may also be standardized. The
Session State Management Function may be physically realized as part
of the CallBroker Server.
6.1.2 IP Client to CallBroker Interface
Communication on the IP Client to CallBroker Interface (Interface 1
in Figure 12) is a simple ASCII based protocol running directly on
TCP. The messages on this interface are primarily requests from the
client to the CallBroker, responses from the CallBroker to the IP
client responding to the requests and unsolicited events from the
CallBroker to the IP client. Since the communication is not strictly
transaction oriented, traditional encapsulation protocols like HTTP
cannot be used. There has been some ongoing work attempting to use
multiple concurrent HTTP POST requests to support event delivery but,
without too much difficulty, the ASCII protocol specified here can
easily be mapped to the POST payload of the HTTP protocol.
6.1.3 Protocol
Basic Format
The basic format of the protocol is as follows:
[header]<<LF>
<<LF>
[body]<<LF>
<<LF>
<<LF>
The header and body of the protocol are separated by 2 line feed
characters. The format of the header and the body is described
below. Line feed characters in the header or body will be escaped
using simple URL encoding.
Header
[session-id | 0]<<LF>
[message-id]<<LF>
[version-info]<<LF>
All CallBroker transactions are identified by sessions. A session
does not necessarily correspond one-to-one to a TCP session. If the
IP client is attempting to initiate a new session with the CallBroker
the session-id field is populated with '0' to indicate session
creation request. Every session request needs to be accompanied by
sufficient information regarding authentication for the CallBroker to
create the session.
Message-id represents the operation of the message.
Version-info contains optional version information of the protocol.
This is to aid possible version mismatch detection and graceful error
recovery.
Body
The body of the protocol messages consists of name value pairs. These
name-value pairs are interpreted with reference to the message-id
which signifies the operation to be performed by the CallBroker.
6.1.4 APIs Exposed to the IP Client
The APIs of the CallBroker exposed to the IP client are distinct and
different from the APIs that the CallBroker uses from the different
supporting subsystems including the authentication subsystem and the
usage recording subsystem. The IP client APIs enable clients to
effectively control voice conferencing.
6.1.5 Voice-Bridge Control API
The Voice Bridge Control API is used by CallBroker applications to
access voice bridging functionality. The API distinguishes between
sessions and calls. Calls represent actual voice calls placed from/to
the voice bridge. These calls can be grouped together in sessions.
All the calls that belong to a session are bridged. Calls have a
significance outside the scope of sessions. Every call can be
associated with multiple sessions with different weights at the same
time. The advantage of this approach is the ability to support
concepts like whispering in a conference call. Calls can also be
dropped from a conference session and bridged together in a new
session to give the notion of a sub-conference. These calls can later
be re-added to the main conference session.
6.2 Simple Computer Telephony Protocol
6.2.1 Overview
The Simple Computer Telephony Protocol (SCTP) is a third party call
control protocol and as such does not comply with the PINT charter.
SCTP is described in this section to show how PINT services could be
implemented using SCTP, and where SCTP fits into the PINT
architecture.
In addition to third party call control, SCTP also provides
subscriber (i.e., user) feature management (e.g., allows a user to
set do not disturb, call forwarding parameters), and subscriber
monitoring of terminal, line and address status. SCTP is strictly
client/server-based. It has no provisions for peer to peer
communications. SCTP runs as a TCP application protocol. It is
ASCII-based and uses sockets. The SCTP Server is usually connected to
a switch via a CTI (Computer-Telephony Integration) connection.
Because of this, feature interactions are limited to those within the
context of a single call, and not between PSTN services. The SCTP
Server within a PINT Gateway could also be connected to an SN, or an
SCP. See figures below. SCTP does NOT carry media.
6.2.2 How SCTP Fits in with the Reference PINT Services
SCTP Client as Part of a Web Server
+------+ +--------+ +--------+ +------+
| | | | SCTP | | | |
| |----| |-------| |----| |
| | | | | | | |
+------+ +--------+ +--------+ +------+
User's PC Web Server/ PINT Gateway SN/SCP/Switch
CGI
Figure 14: SCTP Client as Part of a Web Server
In this architecture, the SCTP Client is embedded in the Web Server.
It is there for the specific purpose of initiating calls to the PSTN
based on user requests. The SCTP Server is within the PINT Gateway.
We go through the classic PINT examples:
Click-to-dial-back: The SCTP Client issues an SCTP MakeCall to the
SCTP Server with the calling number supplied by Web page, and called
number supplied by the user.
Click-to-fax-back: SCTP Client issues an SCTP MakeCall to the SCTP
Server with called number set to user's fax machine, and calling
number set to Web Server's fax machine, and treatment set to the URI
for the file to be faxed. The SCTP Server takes the file and feeds
it into the call just as a fax machine would.
Click-to-fax: SCTP Client issues an SCTP MakeCall with calling number
set to user's fax machine, and called number set to Web Server's fax
machine. How the file is supplied to the user's fax machine is
outside the scope of SCTP.
Voice-access-to-content: SCTP Client issues an SCTP MakeCall with
called number set to user's telephone number, and calling number set
to Web Server and treatment set to a URI for the file of the
particular Web page to be read to the called number. The SCTP Server
takes care of the file to voice conversion and this is fed into the
call as if it were voice.
In all of the above cases, the SCTP Client can generate a variety of
different Web pages to send to the Web Server via CGI (Common Gateway
Interface). The content of these pages is based on the call
completion status of the CallMake SCTP action.
SCTP Client Running on the User's PC
+------+
HTML | | INTERNET
+-----+ /--------------| |
| |---/ +------+
| | Web Server
| |---\
+-----+ \
User's PC \ SCTP +------+ +------+
\------------| |-------| | PSTN
| | | |
+------+ +------+
PINT Gateway SN/SCP/Switch
Figure 15: SCTP Client Running on the User's PC
In this architecture, the user has an SCTP Client co-located with it.
If the user is using the telephone line for connection to a Web
Server and there is an incoming call, then the SCTP Server in the
PINT Gateway will post this event to the SCTP Client. A window will
pop up on the user's screen with options available to the user for
handling of the incoming call. The user can choose to take the call,
send it to voice mail, or send it to another number.
For the Fax back service, for example, if the user had a separate fax
machine from his or her PC, then the SCTP Server would tell the SCTP
Client there is an incoming fax. The user would end or suspend his or
her Internet connection, the fax would come in, and the user could
then resume the Internet connection.
7. Session Initiation Protocol--An Emerging Standard
7.1 Overview
SIP, the Session Initiation Protocol, is a simple signaling protocol
for Internet conferencing and telephony. It is currently under
development within the IETF MMUSIC (Multiparty Multimedia Session
Control) Working Group.
SIP provides the necessary mechanisms to support the following
services:
- call forwarding, including the equivalent of 700-, 800- and 900-
type calls;
- call-forwarding no answer;
- call-forwarding busy;
- call-forwarding unconditional;
- other address-translation services;
- callee and calling "numbers" delivery, where the numbers can be of
any (preferably unique) naming scheme;
- personal mobility, i.e., the ability to reach a called party under
a single, location-independent address, even when the user changes
terminals;
- terminal-type negotiation and selection: a caller can be given a
choice of how to reach a party, e.g., via Internet telephony,
mobile, phone, and an answering service;
- caller and callee authentication;
- blind and supervised call transfer;
- user location; and
- invitation to multicast conferences.
Extensions of SIP to allow third-party signaling (e.g., for click-
to-dial-back services, fully meshed conferences and connections to
Multipoint Control Units (MCUs), as well as mixed modes and the
transition between those) have been specified.
SIP addresses (URLs) can be embedded in Web pages. SIP is
addressing-neutral, with addresses expressed as URLs of various types
such as SIP, H.323 or telephone (E.164). A purely representational
example of a SIP URL might be sip:+12125551212@foo.example.com, where
foo.example.com is the host serving as a gateway into the PSTN.
SIP is independent of the packet layer and only requires an
unreliable datagram service, as it provides its own reliability
mechanism. While SIP typically is used over UDP or TCP, it could,
without technical changes, be run over IPX, or carrier pigeons, ATM
AAL5 or X.25, in rough order of desirability.
SIP can set up calls "out-of-band". For example, while the SIP
protocol exchanges use IP, plus UDP or TCP, the actual data transport
can take place via the PSTN. This feature makes it possible to use
SIP to control a PBX or send requests to a Service Control Point. The
PINT services make use of this flexibility.
7.2 SIP Protocol
SIP is a textual client-server protocol, similar in syntax to HTTP
and RTSP. Requests consist of a method (INVITE, BYE, ACK, or
REGISTER), a list of parameter-value pairs describing the request and
an optional request body. Parameters include the origin and
destination of the call and a unique call identifier. They may
indicate the caller's organization as well as the call's subject and
priority. The request body contains a description of the call to be
established or the conference to be joined. The description format is
not prescribed by SIP; SDP is one possibility being standardized
within the IETF. For the purposes of providing PINT services, an
additional phone number address format is to be added to SDP.
Responses indicate whether a request is still being processed, was
successful, can possibly be satisfied by another node or failed. When
a call is redirected, the response indicates the name of the node to
be tried. Unsuccessful calls may also return a better time to try
again.
In a typical successful call, the caller sends an INVITE request to
the callee. The callee accepts the call by returning a response code
to the callee, which then confirms the receipt of that acceptance
with an ACK request. Either side can terminate the call by sending a
BYE request.
Requests can be authenticated using standard HTTP password and
challenge-response mechanisms. Requests and responses may also be
signed and encrypted.
7.3 SIP entities
SIP distinguishes three kinds of entities:
User agents receive and initiate calls and may forward the call.
A proxy server is an intermediary program that acts as both a server
and a client for the purpose of making requests on behalf of other
clients. Requests are serviced internally or by passing them on,
possibly after translation, to other servers. A proxy must interpret,
and, if necessary, rewrite a request message before forwarding it. A
proxy server may, for example, locate a user and then attempt one or
more possible network addresses.
Redirect server accepts a SIP request, maps the address into zero or
more new addresses and returns these addresses to the client. Unlike
a proxy server, it does not initiate its own SIP request. Unlike a
user agent server, it does not accept calls.
Proxy and redirect servers may make use of location servers that
determine the current likely location of the callee.
A PSTN gateway initiates phone calls between two parties. This may be
a server that sends requests to an SCP in an IN environment or it may
be a CTI-controlled PBX.
A SIP call may traverse one or more proxy servers.
The servers that control a PBX or an SCP act as user agents. A Web
server may also act as a SIP user agent.
7.4 Providing Call Control Functionality
The SIP for PINT specification provides details on how to use SIP to
initiate phone calls between two PSTN end points. (SIP can also
initiate calls between Internet end points and between an Internet
and PSTN end point, but this is beyond the scope of this document.)
It should be noted that the SIP client for initiating such phone
calls can be either at the user's location (his/her workstation) or
can be a Web server that calls up a SIP client via a CGI program.
There is no difference in operation or functionality, except that the
owner of the Web server may be legally responsible for the calls
made.
A SIP client needs to convey two addresses to the PSTN gateway: the
party making the call and the party to be called. (The party to be
billed also needs to be identified; this can either be done by a SIP
header or by having the server look up the appropriate party based on
the two parties. This aspect is for further study.)
Described below are three ways these addresses can be conveyed in
SIP. In the example, the address of party A is +1-212-555-1234 and
that of party B is +1-415-555-1200. (The URL types in this and other
examples are representational; they may but do not have to exist.)
(1) The two PSTN addresses are contained in the To header (and
request-URI) and an Also header. For example:
INVITE sip:+1-212-555-1234@pbx.example.com SIP/2.0
To: phone:1-212-555-1234
From: sip:j.doe@example.com
Content-type: application/sdp
Call-ID: 19970721T135107.25.181@foo.bar.com
Also: phone:+1-415-555-1200
v=0
o=user1 53655765 2353687637 IN IP4 128.3.4.5
c=PSTN E.164 +1-415-555-1200
t=0 0
m=audio 0 RTP/AVP 0
In that case, the gateway first connects to party A and then party B,
but without waiting for A to accept the call before calling B.
(2) Parties A and B are indicated by separate invitations. This
allows the gateway to make sure that party A is indeed available
before calling party B. After calling party A, the gateway could
play an announcement indicating that the call is being connected
using, for example, RTSP with appropriate Conference header
indicating the call.
INVITE sip:+1-212-555-1234@pbx.example.com SIP/2.0
To: phone:1-212-555-1234
From: sip:j.doe@example.com
Content-type: application/sdp
Call-ID: 19970721T135107.25.181@foo.bar.com
...
INVITE sip:+1-415-555-1200@pbx.example.com SIP/2.0
To: phone:+1-415-555-1200
From: sip:j.doe@example.com
Content-type: application/sdp
Call-ID: 19970721T135107.25.181@foo.bar.com
...
(3) The two PSTN addresses are conveyed in the To header of the SIP
request and the address in the SDP media description. Thus, a request
may look as follows:
INVITE sip:+1-212-555-1234@pbx.example.com SIP/2.0
To: phone:1-212-555-1234
From: sip:j.doe@example.com
Content-type: application/sdp
Call-ID: 19970721T135107.25.181@foo.bar.com
v=0
o=user1 53655765 2353687637 IN IP4 128.3.4.5
c=PSTN E.164 +1-415-555-1200
t=0 0
m=audio 0 RTP/AVP 0
Here, pbx.example.com is the name of the PSTN gateway; the call will
be established between 1-212-555-1234 and +1-415-555-1200.
Users can be added to an existing call by method (1) or (2).
8. Overall Security Considerations
Inter-networking of the Internet and PSTN necessitates the
introduction of new interfaces (e.g., the A, B and E interfaces in
Figure 6). To ensure that their use does not put the networks, in
particular the PSTN, at additional security risk, these interfaces
need to be designed with proper security considerations. Sections
5.1.5 and 5.2.2.7 describe how two of the pre-PINT implementations,
the Lucent and Siemens systems, handle the security aspect,
respectively.
Worth noting are the security requirements suggested by pre-PINT
experiences. They are:
+Peer entity authentication to allow a communicating entity to prove
its identity to another in the network (e.g., the requesting IP-host
to the PINT gateway, and the PINT gateway to the PSTN node providing
the service control function).
+Authorization and access control to verify if a network entity
(e.g., the requesting IP-host) is allowed to use a network resource
(e.g., requesting services from the PINT gateway).
+Non-repudiation to account for all operations in case of doubt or
dispute.
+Confidentiality to avoid disclosure of information (e.g., the end
user profile information and data) without the permission of its
owner.
In the course of the PINT interface development, additional
requirements are likely to arise. It is imperative that the resultant
interfaces include specific means to meet all the security
requirements.
9. Conclusion
This document has provided the information relevant to the
development of inter-networking interfaces between the PSTN and
Internet for supporting PINT services. Specifically, it addressed
technologies, architectures, and several existing pre-PINT
implementations of the arrangements through which Internet
applications can request and enrich PSTN telecommunications services.
One key observation is that the pre-PINT implementations, being
developed independently, do not inter-operate. It is a task of the
PINT Working Group to define the inter-networking interfaces that
will support inter-operation of the future implementations of PINT
services.
10. Acknowledgments
The authors would like to acknowledge Scott Bradner, Igor Faynberg,
Dave Oran, Scott Petrack, Allyn Romanow for their insightful comments
presented to the discussions in the PINT Working Group that lead to
the creation of this document.
11. Appendix
11.1 PSTN/IN 101
11.1.1 Public Switched Telephone Network
What is normally considered as "the Telephone Network" consists of a
set of interconnected networks. Potentially, each of these networks
could be owned by a different Network Operator. The official name for
such a network is Public Switched Telecommunications Network (PSTN).
A simple PSTN consists of a set of Switches (called Central Offices
or Telephone Exchanges) with links interconnecting them to make up
the network, along with a set of access connections by which
terminals are attached. The PSTN is used to deliver calls between
terminals connected to itself or to other PSTNs with which it is
interconnected. Calls on the PSTN are circuit switched; that is, a
bi-directional connection is made between the calling and called
terminals for the duration of the call. In PSTNs the connection is
usually carried through the network in digital format occupying a
fixed bandwidth; this is usually 56 or 64 Kbps. The overall
configuration of the PSTN is shown in Figure 16.
/--\
()/\()__
/__\ \ .................................
\ ! ! ! /--\
__ \ [-!-] [-!-] ! ()/\()
\ \ \__[CO ]=========[CO ]==\\ ! ___/__\
[Fax]________[---] [---] \\ [-!-] / __
\\=======[CO ]____/ \ \
[---]________[Fax]
Key: ___ Access Lines
=== Trunk Links (inter-CO user data links)
... Inter-CO signaling network links
Figure 16
Messages are sent between the Switches to make and dissolve
connections through the network on demand and to indicate the status
of terminals involved in a call; these "signaling" messages are
carried over a separate (resilient) data network dedicated to this
purpose. This signaling network is also known as the Common Channel
Signaling (CCS) or Signaling System Number 7 (or SS7) network after
the names of the signaling protocol suite used.
As yet, the majority of access connections to a PSTN carry analogue
signals, with simple (analogue) telephones or Facsimile machines as
terminals. Call requests are indicated to the Central Office to which
a telephone is connected either by a sequence of pulses or tone pairs
being sent. Notifications on the status of the request are sent back
to the telephone in the form of tones. Indication from a Central
Office that a call is being offered to a telephone is arranged by
sending an alternating voltage down the access connection which in
turn causes the ringer in the telephone to sound. These access lines
have a unique address associated with them and can support a single
call.
However, with analogue or digital multi-line connections, or
Integrated Service Digital Network (ISDN) Basic or Primary Rate
Interfaces (BRI or PRI), several concurrent calls are possible and a
set of addresses are associated with them. The new ISDN access
connections are designed so that data exchanged with the network is
in multiplexed digital form, and there is an individual channel for
each of the potential connections, together with a separate channel
dedicated to sending and receiving call request and call alert data
as well as carrying packet switched user data. These call request and
call alert messages act as the equivalent of the pulses or tones that
are sent when dialing, and the ringing signal that is sent to a
telephone when a call is being made to it.
The operation of the call request is fairly simple in most cases and
is shown in Figure 17.
/--\
() ()
--____
/++\ \ ................................. /--\
/----\ \ ^ v ! () ()
A \ [-!-] [-!-] ! --
\->[CO ]=========[CO ]==\\ v ->-/ \
[---] [---] \\ [-!-] / /----\
\\=======[CO ]____/ B
[---]
Key: ___ Access Lines
=== Trunk Links (inter-CO user data links)
... Inter-CO signaling network links
CO Central Office (Telephone Exchange)
Figure 17
The user presses a sequence of numbers on a telephone handset
(labeled A), and the telephone passes a sequence of digits (either as
pulses or tone pairs) to the Central Office via the access line. The
Central Office contains a processor that will be notified that the
user has made a request and the digit string that is the sole
parameter of the request. This digit string is taken to be the unique
address of an access line connected either to itself or to another
Central Office. There is a hierarchical addressing scheme, so that
the digit string can be parsed easily. A call request to a terminal
(labeled B) connected to a remote Central Office can be routed by
examining the digit string passed; the Central Office will extract
the part of the passed address that corresponds to the remote Central
Office in question, and can route the request onward, forming an
inter-Switch call request and passing it via the signaling network.
At the same time it will allocate one of its available transmission
channels towards the remote Central Office.
11.1.2 Intelligent Network
This scheme has been used since the 1950s, and suffices for the
majority of calls. However, there are a range of other services that
can be (and have been) provided, enhancing this basic call
processing. Freephone or Premium Rate services (1-800 or 1-900
services) are good examples of the supplementary services that have
been introduced. Apart from the important feature that the cost of
these calls is varied so that the caller does not pay for a free-
phone call, or pays an extra charge for a premium rate call, they
have the similarity that the number dialed must be translated to
arrive at the "real" address of the destination terminal. They are
known as number translation services, and make up the bulk of all
supplementary services delivered today.
These were originally programmed into each Central Office, but the
complexity of maintaining the data tables on each processor grew
cumbersome, so a more general solution was sought. After a
considerable gestation period, the eventual solution was the
Intelligent Network. This takes the separation of Central Offices and
the network links interconnecting them a stage further.
The Central Offices are considered to provide the Call Control
Function (CCF). In addition, the Service Switching Function (SSF) is
provided to "enhance" the operation of these Switches by detecting
when a particular request has been made (such as by dialing 1-800).
If this pattern is detected, the equipment implementing the SSF will
send a specialized request message over the signaling network to a
separate computer that implements the Service Control Function (SCF).
This entity is responsible for querying service specific data (held
in a unit providing the Service Data Function, or SDF), performing
any digit translations necessary, and sending the details of how to
proceed back to the SSF, where they are obeyed and the call is put
through to the "real" destination. In many implementations, the SDF
is closely coupled to the SCF. This configuration is shown in Figure
18.
[---] [---] [---]
/--\ [SRF] [SCF] [SDF]
()/\()__ [|-!] [-!-] [-!-]
/__\ \ || \.............!......!........
\ || / ! ! /--\
__ \ [|-!] [-!-] ! ()/\()
\ \ \__[SSF] [CCF] ! ___/__\
[Fax]________[CCF]=========[---]==\\ [!--] / __
\\========[CCF]__/ \ \
[---]_______[Fax]
Key: ___ access relationship
=== trunk relationship
... signaling relationship
Figure 18
The advantage is that there can be a much smaller number of physical
units dedicated to the SCF, and as they are connected to the
signaling network they can be contacted by, and can send instructions
back to, all of the units providing the SSF and thus the CCF.
In another enhancement, a separate entity called the Special Resource
Function (SRF) was defined. Equipment implementing this function
includes announcement units to play recorded messages (for example,
prompts to enter digits) to callers. It will also include the tone
decoders needed to capture any digits pressed by the caller in
response to the prompts. It is connected to the rest of the PSTN
usually via trunk data links. It will also include a signaling
connection (directly or indirectly) back to the SCF, via the PSTN's
core signaling network.
As an example of the way that these different functional entities
interact, the SCF can ask an SSF handling a call to route the caller
temporarily through to an SRF. In response to instructions sent to it
from the SCF over the signaling network, the SRF can play
announcements and can collect digits that the user presses on their
terminal in response to prompts they are played. Once these digits
have been collected they can be passed on to the SCF via a signaling
message for further processing. In normal operation, the SCF would
then ask the SSF to dissolve the temporary connection between the
user's terminal and the SRF. This allows the collection of account
numbers or passwords (or PINs) and forms the heart of many "Calling
Card" services.
This pattern of user interaction is also used in a wide variety of
other services where extra account information and PINs are needed.
They are collected as just described and can be checked against the
correct values stored in the service database prior to allowing the
call to proceed.
The Intelligent Network functional entities can be realized as
physical units in a number of different combinations. A common
configuration is shown in Figure 19.
[---] [---] [---] [---]
/--\ [I.P] [SCP] [SDP] [SN ]
()/\()__ [|-!] [-!-] [-!-] [--|]
/__\ \ || \.............!.....!..... |
\ || / ! \ | /--\
__ \ [|-!] [-!-] \ | ()/\()
\ \ \__[SSP]=========[CO ]==\\ \ | ___/__\
[Fax]________[---] [---] \\ [!-|] / __
\\=======[CO ]__/ \ \
[---]_______[Fax]
Key: ___ Access Lines
=== Trunk Links (inter-CO user data links)
... Inter-CO signaling network links
SSP Service Switching Point - a unit that implements the
Service Switching Function
CCP Call Control Point - a unit that performs call control
functions.
This is normally a kind of Central Office (shown as CO
above)
SCP Service Control Point - a unit implementing the Service
Control Function. NOTE that this is connected to the SS7
Network and uses this connection for all of its
communications.
I.P Intelligent Peripheral - a unit that contains specialized
resources (like announcement units, tone decoders).
In effect, it implements Special Resource Functions.
SN Service Node
Figure 19
This diagram also shows a unit called a Service Node, or SN. This
contains components that realize all of the operational Intelligent
Network functions (SSF, SCF, SDF, and SRF). It is sometimes more
convenient to have all of these elements in one node (for example,
for operations and maintenance reasons), particularly within smaller
PSTNs or where there is a relatively low level of requests for
particular services. Another difference is that, as they are all co-
located, proprietary protocols can be used for internal
communication, rather than the full Intelligent Network Application
Part (INAP) protocol used over the core signaling network between
discrete units. It also differs from the "unbundled" approach in that
it is connected to the COs within a PSTN as a peripheral, having only
an access connection to a Central Office; there is no connection to
the core signaling network. Other than this, it operates in a similar
way, and can provide the same kinds of services. Information on the
specification of the Intelligent Network can be found in the ITU
recommendations [1], while two books ([2] and [3]) describe the
system, its history, operation, and the philosophy behind it.
11.2 Call Center Features
A Call Center is a system that allows a company to be organized with
a group of similar individuals (agents), all of whom can either make
calls to, or take calls from, customers. The system distributes
incoming calls to the agents based on their availability and
automates the placement of outgoing calls, selecting an agent to
handle the call and routing the call to them only once the call
request has been made of the PSTN.
The incoming call distribution feature ("automatic call
distribution", or ACD) is usually coupled with a call queuing scheme.
In this scheme, the callers are connected temporarily with an
announcement unit that normally plays music. The calls are treated in
sequence so that (once the caller is at the front of the queue) the
ACD system selects the next available agent and routes the call
through to them.
Another feature connects a customer making an incoming call to a unit
that asks them for some information on the purpose of their call,
selecting the agent to handle the call based on the particular area
of expertise needed; to do this, the agents are further categorized
by their knowledge (or "Skill Set"). If this skill set categorization
is used then by implication there will be separate queues for each of
the skill sets. This user selection scheme can be used independently
of the others. For example these so-called "voice navigation systems"
can be used to select a particular department extension number, based
on the function required by the customer; as such, they can automate
the job of company telephone receptionist in routing incoming calls.
Where possible, the information gleaned from the customer can be
provided to the selected agent, usually via a separate networked
computer connection. Similarly, if an outgoing call is being made to
one of a list of customers, information on the customer and the
purpose of the call can be provided to the agent selected to handle
the call. Such configurations are generally called "Computer
Telephony Integration" or CTI systems. Strictly, a CTI system can be
arranged to handle routing of incoming calls and automation of
outgoing calls only (also known as computer integrated telephony
features), without the agents having access to a network of
computers. However, the business case for combining the telephony
functions of the call center with provision to the agents of
computers with customer information can be compelling.
This is often further combined with a company's order and service
processing computer system. In this case, a call is treated as part
of a business transaction, with the information to be exchanged
captured as fields of a computer form. While such a computer system
is not, strictly, part of a call center, integrating the company
computer system with the call center is very common. This allows the
details of the call to be stored on a centralized database, allowing
further automated order processing, for example. It also allows the
call to be transferred from one agent to another where needed,
ensuring that the new agent has the information already captured.
This might be useful if someone with a different area of expertise
were to be needed to handle the customer's requirements.
Traditionally, Call Centers have been used to support teams of agents
working at a single site (or a small number of sites, with private
telephony trunks interconnecting them). The site Private Automatic
Branch eXchange (PABX) was integrated with a computer system to
provide these features to people at that site. There can be a
business case for provision of such features to distributed teams of
workers as well. In particular, the possibility of providing support
for people working from home has been seen as important. Some of the
Call Center features have been incorporated into public telephone
exchanges or Central Offices (COs) from many manufacturers as part of
their "Centrex" service offerings.
There are practical limitations in providing such features on COs.
Apart from the procedures needed to configure these features for any
telephone line that is to use them, the basic requirement that every
agent must have a connection to the supporting CO can limit its
usefulness. Another approach is to provide Call Center features via
the Intelligent Network. The features might thus be provided over a
Telephone Operator's entire network, and would mean that the Call
Center could be configured centrally while still allowing agents to
be located anywhere within the telephone network. It also means that
the supported company can pay for the Call Center features "as they
go" rather than having a high "up front" cost.
12. References
[1] ITU-T Q.12xx Recommendation Series, Geneva, 1995.
[2] I. Faynberg, L. R. Gabuzda, M. P. Kaplan, and N. J. Shah, "The
Intelligent Network Standards, their Application to Services",
McGraw-Hill, 1996.
[3] T. Magedanz and R. Popesku-Zeletin, "Intelligent Networks: Basic
Technology, Standards and Evolution", Intl. Thomson Computer
Press, 1996.
[4] Information processing systems - Open Systems Interconnection -
Specification of Abstract Syntax Notation One (ASN.1),
International Organization for Standardization, International
Standard 8824, December, 1987.
[5] McCloghrie, K., Editor, "Structure of Management Information for
Version 2 of the Simple Network Management Protocol (SNMPv2)",
RFC 1902, January 1996.
[6] Kristol, D. and L. Montulli, "HTTP State Management Mechanism",
RFC 2109, February 1997.
[7] Zimmerman, D., "The Finger User Information Protocol", RFC 1288
December 1991.
Authors' Addresses
Steve Bellovin
AT&T Labs
Room E-215
180 Park Ave. Bldg. 103
Florham Park, NJ 07932-0000
USA
Phone: +1 973 360 8656
Fax: +1 973 360 8077
EMail: smb@research.att.com
Fred M. Burg
AT&T Labs
Room 1N-117
307 Middletown Lincroft Road
Lincroft, NJ 07738
USA
Phone: +1 732 576 4322
Fax: +1 732 576 4317
EMail: fburg@hogpb.att.com
Lawrence Conroy
Roke Manor Research Limited
IT&N-INIA Group
Roke Manor, Old Salisbury Lane,
Romsey, Hampshire SO51 0ZN
U.K.
Phone: +44 1794 833666
Fax: +44 1794 833434
EMail: lwc@roke.co.uk
Paul Davidson
Nortel
P.O.Box 3511 Station "C"
Mail Stop 242
Ottawa, Ontario, Canada K1Y 4H7
Phone: +1 613 763 4234
EMail: pauldav@nortel.ca
A. DeSimone
Lucent Technologies
Room 6H510
600-700 Mountain Avenue
Murray Hill, NJ 07974-0636
USA
Phone: +1 908 582 2382
Fax: +1 908 582 1086
E-Mail:tds@lucent.com
Murali Krishnaswamy
Bell Laboratories
Lucent Technologies
Room 2G-527a
101 Crawfords Corner Road
Holmdel, NJ 07733-3030
USA
Phone: +1 732 949 3611
Fax: +1 732 949 3210
EMail: murali@bell-labs.com
Hui-Lan Lu
Bell Laboratories
Lucent Technologies
Room 4K-309
101 Crawfords Corner Road
Holmdel, NJ 07733-3030
USA
Phone: +1 732 949 0321
Fax: +1 732 949 1196
EMail: hui-lan.lu@bell-labs.com
Henning Schulzrinne
Dept. of Computer Science
Columbia University
New York, NY 10027
USA
Phone: +1 212 939 7042 (@Bell Labs: 732 949 8344)
Fax: +1 212 666 0140
EMail: schulzrinne@cs.columbia.edu
Kamlesh T. Tewani
AT&T Labs
Room 1K-334
101, Crawfords Corner Rd.
Holmdel, NJ 07733
USA
Phone: +1 732 949 5369
Fax: +1 732 949 8569
EMail: tewani@att.com
Kumar Vishwanathan
Isochrone
EMail: kumar@isochrone.com
Full Copyright Statement
Copyright (C) The Internet Society (1998). All Rights Reserved.
This document and translations of it may be copied and furnished to
others, and derivative works that comment on or otherwise explain it
or assist in its implementation may be prepared, copied, published
and distributed, in whole or in part, without restriction of any
kind, provided that the above copyright notice and this paragraph are
included on all such copies and derivative works. However, this
document itself may not be modified in any way, such as by removing
the copyright notice or references to the Internet Society or other
Internet organizations, except as needed for the purpose of
developing Internet standards in which case the procedures for
copyrights defined in the Internet Standards process must be
followed, or as required to translate it into languages other than
English.
The limited permissions granted above are perpetual and will not be
revoked by the Internet Society or its successors or assigns.
This document and the information contained herein is provided on an
"AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.