Rfc2494
TitleDefinitions of Managed Objects for the DS0 and DS0 Bundle Interface Type
AuthorD. Fowler, Ed.
DateJanuary 1999
Format:TXT, HTML
Status:PROPOSED STANDARD






Network Working Group                               D. Fowler, Editor
Request for Comments: 2494                         Newbridge Networks
Category: Standards Track                                January 1999


                     Definitions of Managed Objects
               for the DS0 and DS0 Bundle Interface Type

Status of this Memo

   This document specifies an Internet standards track protocol for the
   Internet community, and requests discussion and suggestions for
   improvements.  Please refer to the current edition of the "Internet
   Official Protocol Standards" (STD 1) for the standardization state
   and status of this protocol.  Distribution of this memo is unlimited.

Copyright Notice

   Copyright (C) The Internet Society (1999).  All Rights Reserved.

Abstract

   This memo defines a portion of the Management Information Base (MIB)
   for use with network management protocols in the Internet community.
   In particular, it describes objects used for managing DS0 and DS0
   Bundle interfaces.  This document is a companion document with
   Definitions of Managed Objects for the DS1/E1/DS2/E2 (RFC 2495 [17]),
   DS3/E3 (RFC 2496 [18]), and the work in progress, SONET/SDH Interface
   Types.

   This memo specifies a MIB module in a manner that is both compliant
   to the SNMPv2 SMI, and semantically identical to the peer SNMPv1
   definitions.

Table of Contents

   1 The SNMP Management Framework ................................    2
   2 Overview .....................................................    3
   2.1 BONDing Terminology ........................................    3
   2.2 Use of ifTable for DS0 Layer ...............................    3
   2.3 Using ifStackTable .........................................    4
   2.3.1 Usage of Channelization for DS3, DS1, DS0 ................    6
   2.3.2 Usage of ifIndex Mapping for DS0Bundle ...................    7
   3 Overview of the MIB ..........................................    7
   3.1 DS0 MIB ....................................................    8
   3.2 DS0Bundle MIB ..............................................    8
   4 Object Definitions for DS0 ...................................    8
   4.1 The DS0 Config Group .......................................    9



RFC 2494                DSO MIB / DSOBUNDLE MIB             January 1999


   4.1.1 The DS0 Configuration Table ..............................    9
   4.1.2 The DS0 Channel Mapping Table ............................   12
   5 Object Definitions for DS0 Bundle ............................   15
   5.1 The DS0 Bundle Config Group ................................   15
   5.1.1 The DS0 Bundle Table .....................................   15
   5.2 The DS0 Bonding Group ......................................   18
   5.2.1 The DS0 Bonding Table ....................................   18
   6 Intellectual Property ........................................   21
   7 Acknowledgments ..............................................   22
   8 References ...................................................   22
   9 Security Considerations ......................................   23
   10 Author's Address ............................................   24
   11 Full Copyright Statement ....................................   25

1.  The SNMP Management Framework

   The SNMP Management Framework presently consists of five major
   components:

    o   An overall architecture, described in RFC 2271 [1].

    o   Mechanisms for describing and naming objects and events for the
        purpose of management. The first version of this Structure of
        Management Information (SMI) is called SMIv1 and described in
        STD 16, RFC 1155 [2], STD 16, RFC 1212 [3] and RFC 1215 [4]. The
        second version, called SMIv2, is described in RFC 1902 [5], RFC
        1903 [6] and RFC 1904 [7].

    o   Message protocols for transferring management information. The
        first version of the SNMP message protocol is called SNMPv1 and
        described in STD 15, RFC 1157 [8]. A second version of the SNMP
        message protocol, which is not an Internet standards track
        protocol, is called SNMPv2c and described in RFC 1901 [9] and
        RFC 1906 [10].  The third version of the message protocol is
        called SNMPv3 and described in RFC 1906 [10], RFC 2272 [11] and
        RFC 2274 [12].

    o   Protocol operations for accessing management information. The
        first set of protocol operations and associated PDU formats is
        described in STD 15, RFC 1157 [8]. A second set of protocol
        operations and associated PDU formats is described in RFC 1905
        [13].

    o   A set of fundamental applications described in RFC 2273 [14] and
        the view-based access control mechanism described in RFC 2275
        [15].  Managed objects are accessed via a virtual information
        store, termed the Management Information Base or MIB.  Objects
        in the MIB are defined using the mechanisms defined in the SMI.



RFC 2494                DSO MIB / DSOBUNDLE MIB             January 1999


        This memo specifies a MIB module that is compliant to the SMIv2.
        A MIB conforming to the SMIv1 can be produced through the
        appropriate translations. The resulting translated MIB must be
        semantically equivalent, except where objects or events are
        omitted because no translation is possible (use of Counter64).
        Some machine readable information in SMIv2 will be converted
        into textual descriptions in SMIv1 during the translation
        process. However, this loss of machine readable information is
        not considered to change the semantics of the MIB.

2.  Overview

   These objects are used when the particular media being used to
   realize an interface is a DS0 interface.  At present, this applies to
   these values of the ifType variable in the Internet-standard MIB:

        ds0 (81)
        ds0Bundle (82)

2.1.  BONDing Terminology

   Please reference The BONDing Spec [20] for definitions of terms used
   to describe bonding modes.

2.2.  Use of ifTable for DS0 Layer

   The following items are defined in RFC 2233 [16].

   Only the ifGeneralInformationGroup and ifCounterDiscontinuityGroup
   need to be supported.

              ifTable Object           Use for DS0 Layer
   ======================================================================
              ifIndex                  Interface index.

              ifDescr                  See interfaces MIB [16].

              ifType                   ds0(81) or ds0Bundle(82).

              ifSpeed                  64000 for ds0 (regardless of the
                                       setting of robbed bit signalling)
                                       or N*64000 for ds0Bundle.

              ifPhysAddress            The value of the Circuit
                                       Identifier.  If no Circuit
                                       Identifier has been assigned
                                       this object should have an octet
                                       string with zero length.



RFC 2494                DSO MIB / DSOBUNDLE MIB             January 1999


              ifAdminStatus            See interfaces MIB [16].

              ifOperStatus             See interfaces MIB [16].

              ifLastChange             See interfaces MIB [16].

              ifName                   See interfaces MIB [16].

              ifLinkUpDownTrapEnable   Set to disabled(2).
                                       Supports read-only access.

              ifHighSpeed              Set to rounded ifSpeed/1000000.

              ifConnectorPresent       Set to false(2).

2.3.  Using ifStackTable

   This section describes by example how to use ifStackTable to
   represent the relationship of ds0 and ds0Bundles with ds1 interfaces.
   Implementors of the stack table for ds0 and ds0Bundle interfaces
   should look at the appropriate RFC for the service being stacked on
   ds0s and ds0Bundles.  Examples given below are for illustration
   purposes only.

   Example: A Frame Relay Service is being carried on 4 ds0s of a ds1.

           +---------------------+
           | Frame Relay Service |
           +---------------------+
                      |
           +---------------------+
           | ds0Bundle           |
           +---------------------+
             |     |     |     |
           +---+ +---+ +---+ +---+
           |ds0| |ds0| |ds0| |ds0|
           +---+ +---+ +---+ +---+
             |     |     |     |
           +---------------------+
           | ds1                 |
           +---------------------+

   The assignment of the index values could for example be:

           ifIndex  Description
           1        FrameRelayService (type 44)
           2        ds0Bundle         (type 82)
           3        ds0 #1            (type 81)



RFC 2494                DSO MIB / DSOBUNDLE MIB             January 1999


           4        ds0 #2            (type 81)
           5        ds0 #3            (type 81)
           6        ds0 #4            (type 81)
           7        ds1               (type 18)

   The ifStackTable is then used to show the relationships between the
   various interfaces.

           ifStackTable Entries

           HigherLayer   LowerLayer
           0             1
           1             2
           2             3
           2             4
           2             5
           2             6
           3             7
           4             7
           5             7
           6             7
           7             0


   In the case where the frameRelayService is using a single ds0, then
   the ds0Bundle is not required.

           +---------------------+
           | Frame Relay Service |
           +---------------------+
             |
           +---+
           |ds0|
           +---+
             |
           +---------------------+
           | ds1                 |
           +---------------------+

   The assignment of the index values could for example be:

           ifIndex  Description
           1        FrameRelayService (type 44)
           2        ds0               (type 81)
           3        ds1               (type 18)

   The ifStackTable is then used to show the relationships between the
   various interfaces.



RFC 2494                DSO MIB / DSOBUNDLE MIB             January 1999


           ifStackTable Entries

           HigherLayer   LowerLayer
           0             1
           1             2
           2             3
           3             0

2.3.1.  Usage of Channelization for DS3, DS1, DS0

   An example is given here to explain the channelization objects in the
   DS3, DS1, and DS0 MIBs to help the implementor use the objects
   correctly.  Treatment of E3 and E1 would be similar, with the number
   of DS0s being different depending on the framing of the E1.  Timeslot
   16 is not created for framing types that do not pass data over it.

   Assume that a DS3 (with ifIndex 1) is channelized into DS1s (without
   DS2s).  The object dsx3Channelization is set to enabledDs1.  There
   will be 28 DS1s in the ifTable.  Assume the entries in the ifTable
   for the DS1s are created in channel order and the ifIndex values are
   2 through 29.  In the DS1 MIB, there will be an entry in the
   dsx1ChanMappingTable for each ds1.  The entries will be as follows:

           dsx1ChanMappingTable Entries

           ifIndex  dsx1Ds1ChannelNumber   dsx1ChanMappedIfIndex
           1        1                      2
           1        2                      3
           ......
           1        28                     29

   In addition, the DS1s are channelized into DS0s.  The object
   dsx1Channelization is set to enabledDs0 for each DS1.  When this
   object is set to this value, 24 DS0s are created by the agent. There
   will be 24 DS0s in the ifTable for each DS1.  If the
   dsx1Channelization is set to disabled, the 24 DS0s are destroyed.

   Assume the entries in the ifTable are created in channel order and
   the ifIndex values for the DS0s in the first DS1 are 30 through 53.
   In the DS0 MIB, there will be an entry in the dsx0ChanMappingTable
   for each DS0.  The entries will be as follows:










RFC 2494                DSO MIB / DSOBUNDLE MIB             January 1999


           dsx0ChanMappingTable Entries

           ifIndex   dsx0Ds0ChannelNumber  dsx0ChanMappedIfIndex
           2         1                     30
           2         2                     31
           ......
           2         24                    53

2.3.2.  Usage of ifIndex Mapping for DS0Bundle

   An example is given here to explain the ifIndex mapping objects in
   the DS0Bundle MIB to help the implementor use the objects correctly.

   Assume that a DS1 (with ifIndex 1) is channelized into DS0s.  There
   will be 24 DS0s in the ifTable.  Assume the entries in the ifTable
   for the DS0s are created in channel order and the ifIndex values are
   2 through 25.  Now, assume that there are two bundles on the DS1.
   The first one uses channels 1 and 2.  The second uses channels 3 and
   4.  There will be two ifTable entries for these bundles, with values
   of 26 and 27 for ifIndex.  There will be an entry in the
   dsx0BundleTable for each bundle.  The entries will be as follows:

           dsx0BundleTable Entries

           dsx0BundleIndex    dsx0BundleIfIndex
           1                  26
           2                  27

   There will be an entry in the dsx0ConfigTable for each DS0.  The
   entries will be as follows:

           dsx0ConfigTable Entries

           ifIndex  dsx0Ds0ChannelNumber   dsx0Ds0BundleMappedIfIndex
           2        1                      26
           3        2                      26
           4        3                      27
           5        4                      27
           6        5                      0
           7        6                      0
           ......
           25       24                     0

3.  Overview of the MIB

   This document contains 2 MIB modules, the DS0 MIB and the DS0Bundle
   MIB.




RFC 2494                DSO MIB / DSOBUNDLE MIB             January 1999


3.1.  DS0 MIB

   The DS0 MIB is used to represent individual DS0s in a DS1 or E1.
   Variables in this MIB would be created for each DS0 in the ifTable.
   This MIB contains the following group:

   The DS0 Config Group - This group contains configuration information
   about a particular DS0.

3.2.  DS0Bundle MIB

   The DS0Bundle MIB is used to represent collections of DS0s that are
   used together to carry data within a DS1/E1 at speeds greater than
   that of a single DS0.  DS0Bundles are created on top of DS0s and are
   represented that way in the ifStackTable.  This MIB contains the
   following groups:

   The DS0 Bundle Group - This group contains objects used for creating
   new ds0Bundles.  This group is mandatory.

   The DS0 Bonding Group - This group contains information about bonding
   for a ds0Bundle, if bonding is enabled.  This group is optional.

4.  Object Definitions for DS0

   DS0-MIB DEFINITIONS ::= BEGIN

   IMPORTS
        MODULE-IDENTITY, OBJECT-TYPE,
        transmission                     FROM SNMPv2-SMI
        MODULE-COMPLIANCE, OBJECT-GROUP  FROM SNMPv2-CONF
        DisplayString, TruthValue        FROM SNMPv2-TC
        ifIndex, InterfaceIndex,
        InterfaceIndexOrZero             FROM IF-MIB;

   --  This is the MIB module for the DS0 Interface objects.

   ds0 MODULE-IDENTITY
       LAST-UPDATED "9807161630Z"
       ORGANIZATION "IETF Trunk MIB Working Group"
       CONTACT-INFO
         "        David Fowler

          Postal: Newbridge Networks Corporation
                  600 March Road
                  Kanata, Ontario, Canada K2K 2E6

                  Tel: +1 613 591 3600



RFC 2494                DSO MIB / DSOBUNDLE MIB             January 1999


                  Fax: +1 613 599 3619

          E-mail: davef@newbridge.com"
       DESCRIPTION
            "The MIB module to describe
             DS0 interfaces objects."
       REVISION "9805242010Z"
       DESCRIPTION
            "Initial version of the DS0-MIB."

       ::= { transmission 81 }

   -- The DS0 Config Group

   -- Implementation of this group is mandatory for all
   -- systems that use a DS0 Interface.

   -- The DS0 Config Group consists of two tables:
   --    DS0 Configuration Table
   --    DS0 Channel Mapping Table

   -- The DS0 Configuration Table

   dsx0ConfigTable OBJECT-TYPE
       SYNTAX  SEQUENCE OF Dsx0ConfigEntry
       MAX-ACCESS  not-accessible
       STATUS  current
       DESCRIPTION
               "The DS0 Configuration table."
       ::= { ds0 1 }

   dsx0ConfigEntry OBJECT-TYPE
       SYNTAX  Dsx0ConfigEntry
       MAX-ACCESS  not-accessible
       STATUS  current
       DESCRIPTION
               "An entry in the DS0 Configuration table.  There
               is an entry in this table for each DS0 interface."
       INDEX   { ifIndex }
       ::= { dsx0ConfigTable 1 }

   Dsx0ConfigEntry ::=
       SEQUENCE {
           dsx0Ds0ChannelNumber        INTEGER,
           dsx0RobbedBitSignalling     TruthValue,
           dsx0CircuitIdentifier       DisplayString,
           dsx0IdleCode                INTEGER,
           dsx0SeizedCode              INTEGER,



RFC 2494                DSO MIB / DSOBUNDLE MIB             January 1999


           dsx0ReceivedCode            INTEGER,
           dsx0TransmitCodesEnable     TruthValue,
           dsx0Ds0BundleMappedIfIndex  InterfaceIndexOrZero
   }

   dsx0Ds0ChannelNumber OBJECT-TYPE
       SYNTAX  INTEGER(0..31)
       MAX-ACCESS  read-only
       STATUS  current
       DESCRIPTION
               "This object indicates the channel number of the
               ds0 on its DS1/E1."
       ::= { dsx0ConfigEntry 1 }

   dsx0RobbedBitSignalling OBJECT-TYPE
       SYNTAX  TruthValue
       MAX-ACCESS  read-write
       STATUS  current
       DESCRIPTION
               "This object indicates if Robbed Bit Signalling is
               turned on or off for a given ds0.  This only
               applies to DS0s on a DS1 link.  For E1 links the
               value is always off (false)."
       ::= { dsx0ConfigEntry 2 }

   dsx0CircuitIdentifier OBJECT-TYPE
        SYNTAX  DisplayString (SIZE (0..255))
        MAX-ACCESS  read-write
        STATUS  current
        DESCRIPTION
               "This object contains the transmission vendor's
               circuit identifier, for the purpose of
               facilitating troubleshooting."
       ::= { dsx0ConfigEntry 3 }

   dsx0IdleCode OBJECT-TYPE
        SYNTAX  INTEGER(0..15)
        MAX-ACCESS  read-write
        STATUS  current
        DESCRIPTION
               "This object contains the code transmitted in the
               ABCD bits when the ds0 is not connected and
               dsx0TransmitCodesEnable is enabled.  The object is
               a bitmap and the various bit positions are:
                     1     D bit
                     2     C bit
                     4     B bit
                     8     A bit"



RFC 2494                DSO MIB / DSOBUNDLE MIB             January 1999


       ::= { dsx0ConfigEntry 4 }

   dsx0SeizedCode OBJECT-TYPE
        SYNTAX  INTEGER(0..15)
        MAX-ACCESS  read-write
        STATUS  current
        DESCRIPTION
               "This object contains the code transmitted in the
               ABCD bits when the ds0 is connected and
               dsx0TransmitCodesEnable is enabled.  The object is
               a bitmap and the various bit positions are:
                     1     D bit
                     2     C bit
                     4     B bit
                     8     A bit"
       ::= { dsx0ConfigEntry 5 }

   dsx0ReceivedCode OBJECT-TYPE
        SYNTAX  INTEGER(0..15)
        MAX-ACCESS  read-only
        STATUS  current
        DESCRIPTION
               "This object contains the code being received in
               the ABCD bits.  The object is a bitmap and the
               various bit positions are:
                     1     D bit
                     2     C bit
                     4     B bit
                     8     A bit"
       ::= { dsx0ConfigEntry 6 }

   dsx0TransmitCodesEnable OBJECT-TYPE
        SYNTAX TruthValue
        MAX-ACCESS  read-write
        STATUS  current
        DESCRIPTION
               "This object determines if the idle and seized
               codes are transmitted. If the value of this object
               is true then the codes are transmitted."
       ::= { dsx0ConfigEntry 7 }

   dsx0Ds0BundleMappedIfIndex OBJECT-TYPE
        SYNTAX InterfaceIndexOrZero
        MAX-ACCESS  read-only
        STATUS  current
        DESCRIPTION
               "This object indicates the ifIndex value assigned
               by the agent for the ds0Bundle(82) ifEntry to



RFC 2494                DSO MIB / DSOBUNDLE MIB             January 1999


               which the given ds0(81) ifEntry may belong.

               If the given ds0(81) ifEntry does not belong to
               any ds0Bundle(82) ifEntry, then this object has a
               value of zero.

               While this object provides information that can
               also be found in the ifStackTable, it provides
               this same information with a single table lookup,
               rather than by walking the ifStackTable to find
               the possibly non-existent ds0Bundle(82) ifEntry
               that may be stacked above the given ds0(81)
               ifTable entry."
       ::= { dsx0ConfigEntry 8 }

   -- The DS0 Channel Mapping Table

   dsx0ChanMappingTable OBJECT-TYPE
        SYNTAX  SEQUENCE OF Dsx0ChanMappingEntry
        MAX-ACCESS  not-accessible
        STATUS  current
        DESCRIPTION
               "The DS0 Channel Mapping table.  This table maps a
               DS0 channel number on a particular DS1/E1 into an
               ifIndex."
        ::= { ds0 3 }

   dsx0ChanMappingEntry OBJECT-TYPE
        SYNTAX  Dsx0ChanMappingEntry
        MAX-ACCESS  not-accessible
        STATUS  current
        DESCRIPTION
               "An entry in the DS0 Channel Mapping table.  There
               is an entry in this table corresponding to each
               ds0 ifEntry within any interface that is
               channelized to the individual ds0 ifEntry level.

               This table is intended to facilitate mapping from
               channelized interface / channel number to DS0
               ifEntry.  (e.g. mapping (DS1 ifIndex, DS0 Channel
               Number) -> ifIndex)

               While this table provides information that can
               also be found in the ifStackTable and
               dsx0ConfigTable, it provides this same information
               with a single table lookup, rather than by walking
               the ifStackTable to find the various constituent
               ds0 ifTable entries, and testing various



RFC 2494                DSO MIB / DSOBUNDLE MIB             January 1999


               dsx0ConfigTable entries to check for the entry
               with the applicable DS0 channel number."
        INDEX   { ifIndex, dsx0Ds0ChannelNumber }
        ::= { dsx0ChanMappingTable 1 }

   Dsx0ChanMappingEntry ::=
        SEQUENCE {
            dsx0ChanMappedIfIndex  InterfaceIndex
   }

   dsx0ChanMappedIfIndex OBJECT-TYPE
        SYNTAX  InterfaceIndex
        MAX-ACCESS  read-only
        STATUS  current
        DESCRIPTION
               "This object indicates the ifIndex value assigned
               by the agent for the individual ds0 ifEntry that
               corresponds to the given DS0 channel number
               (specified by the INDEX element
               dsx0Ds0ChannelNumber) of the given channelized
               interface (specified by INDEX element ifIndex)."
        ::= { dsx0ChanMappingEntry 1 }

   -- conformance information

   ds0Conformance OBJECT IDENTIFIER ::= { ds0 2 }

   ds0Groups      OBJECT IDENTIFIER ::= { ds0Conformance 1 }
   ds0Compliances OBJECT IDENTIFIER ::= { ds0Conformance 2 }



   -- compliance statements

   ds0Compliance MODULE-COMPLIANCE
       STATUS  current
       DESCRIPTION
               "The compliance statement for DS0 interfaces."
       MODULE  -- this module
           MANDATORY-GROUPS { ds0ConfigGroup }

           OBJECT dsx0RobbedBitSignalling
           MIN-ACCESS read-only
           DESCRIPTION
               "The ability to set RBS is not required."
           OBJECT dsx0CircuitIdentifier
           MIN-ACCESS read-only
           DESCRIPTION



RFC 2494                DSO MIB / DSOBUNDLE MIB             January 1999


               "The ability to set the circuit identifier is not
               required."

           OBJECT dsx0IdleCode
           MIN-ACCESS read-only
           DESCRIPTION
               "The ability to set the idle code is not
               required."

           OBJECT dsx0SeizedCode
           MIN-ACCESS read-only
           DESCRIPTION
               "The ability to set the seized code is not
               required."

           OBJECT dsx0TransmitCodesEnable
           MIN-ACCESS read-only
           DESCRIPTION
               "The ability to enable and disable the
               transmitting of idle and seized codes is not
               required."

       ::= { ds0Compliances 1 }

   -- units of conformance

   ds0ConfigGroup  OBJECT-GROUP
       OBJECTS { dsx0Ds0ChannelNumber,
                 dsx0RobbedBitSignalling,
                 dsx0CircuitIdentifier,
                 dsx0IdleCode,
                 dsx0SeizedCode,
                 dsx0ReceivedCode,
                 dsx0TransmitCodesEnable,
                 dsx0Ds0BundleMappedIfIndex,
                 dsx0ChanMappedIfIndex }
       STATUS  current
       DESCRIPTION
               "A collection of objects providing configuration
               information applicable to all DS0 interfaces."
       ::= { ds0Groups 1 }

   END








RFC 2494                DSO MIB / DSOBUNDLE MIB             January 1999


5.  Object Definitions for DS0 Bundle

   DS0BUNDLE-MIB DEFINITIONS ::= BEGIN

   IMPORTS
        MODULE-IDENTITY, OBJECT-TYPE,
        transmission                      FROM SNMPv2-SMI
        MODULE-COMPLIANCE, OBJECT-GROUP   FROM SNMPv2-CONF
        DisplayString, RowStatus,
        TestAndIncr                       FROM SNMPv2-TC
        ifIndex, InterfaceIndex           FROM IF-MIB;

   --  This is the MIB module for the DS0Bundle Interface
   --  objects.

   ds0Bundle MODULE-IDENTITY
       LAST-UPDATED "9807161630Z"
       ORGANIZATION "IETF Trunk MIB Working Group"
       CONTACT-INFO
         "        David Fowler

          Postal: Newbridge Networks Corporation
                  600 March Road
                  Kanata, Ontario, Canada K2K 2E6

                  Tel: +1 613 591 3600
                  Fax: +1 613 599 3619

          E-mail: davef@newbridge.com"
       DESCRIPTION
            "The MIB module to describe
             DS0 Bundle interfaces objects."
       REVISION "9805242010Z"
       DESCRIPTION
            "Initial version of the DS0BUNDLE-MIB."

       ::= { transmission 82 }

   --
   -- The DS0 Bundle Config Group
   --
   -- Implementation of this group is mandatory for all
   -- systems that use a DS0Bundle Interface.
   --
   -- The DS0 Bundle Config Group consists of one table:
   --    DS0 Bundle Table

   --  The DS0 Bundle Table



RFC 2494                DSO MIB / DSOBUNDLE MIB             January 1999


   dsx0BundleNextIndex OBJECT-TYPE
       SYNTAX  TestAndIncr
       MAX-ACCESS  read-write
       STATUS  current
       DESCRIPTION
               "This object is used to assist the manager in
               selecting a value for dsx0BundleIndex.  Because
               this object is of syntax TestAndIncr (see the
               SNMPv2-TC document, RFC 1903) it can also be used
               to avoid race conditions with multiple managers
               trying to create rows in the table.

               If the result of the SET for dsx0BundleNextIndex
               is not success, this means the value has been
               changed from index (i.e. another manager used the
               value), so a new value is required.

               The algorithm is:
               done = false
               while done == false
                   index = GET (dsx0BundleNextIndex.0)
                   SET (dsx0BundleNextIndex.0=index)
                   if (set failed)
                     done = false
                   else
                     SET(dsx0BundleRowStatus.index=createAndGo)
                     if (set failed)
                       done = false
                     else
                       done = true
                       other error handling"
       ::= { ds0Bundle 2 }

   dsx0BundleTable OBJECT-TYPE
       SYNTAX  SEQUENCE OF Dsx0BundleEntry
       MAX-ACCESS  not-accessible
       STATUS  current
       DESCRIPTION
               "There is an row in this table for each ds0Bundle
               in the system.  This table can be used to
               (indirectly) create rows in the ifTable with
               ifType = 'ds0Bundle(82)'."
       ::= { ds0Bundle 3 }

   dsx0BundleEntry OBJECT-TYPE
       SYNTAX  Dsx0BundleEntry
       MAX-ACCESS  not-accessible
       STATUS  current



RFC 2494                DSO MIB / DSOBUNDLE MIB             January 1999


       DESCRIPTION
               "There is a row in entry in this table for each
               ds0Bundle interface."
       INDEX   { dsx0BundleIndex }
       ::= { dsx0BundleTable 1 }

   Dsx0BundleEntry ::=
       SEQUENCE {
           dsx0BundleIndex              INTEGER,
           dsx0BundleIfIndex            InterfaceIndex,
           dsx0BundleCircuitIdentifier  DisplayString,
           dsx0BundleRowStatus          RowStatus
   }

   dsx0BundleIndex OBJECT-TYPE
       SYNTAX  INTEGER (0..2147483647)
       MAX-ACCESS  not-accessible
       STATUS  current
       DESCRIPTION
               "A unique identifier for a ds0Bundle.  This is not
               the same value as ifIndex.  This table is not
               indexed by ifIndex because the manager has to
               choose the index in a createable row and the agent
               must be allowed to select ifIndex values."
       ::= { dsx0BundleEntry 1 }

   dsx0BundleIfIndex OBJECT-TYPE
       SYNTAX  InterfaceIndex
       MAX-ACCESS  read-only
       STATUS  current
       DESCRIPTION
               "The ifIndex value the agent selected for the
               (new) ds0Bundle interface."
       ::= { dsx0BundleEntry 2 }

   dsx0BundleCircuitIdentifier OBJECT-TYPE
        SYNTAX  DisplayString (SIZE (0..255))
        MAX-ACCESS  read-create
        STATUS  current
        DESCRIPTION
               "This variable contains the transmission vendor's
               circuit identifier, for the purpose of
               facilitating troubleshooting."
        ::= { dsx0BundleEntry 3 }

   dsx0BundleRowStatus OBJECT-TYPE
       SYNTAX  RowStatus
       MAX-ACCESS  read-create



RFC 2494                DSO MIB / DSOBUNDLE MIB             January 1999


       STATUS  current
       DESCRIPTION
               "This object is used to create and delete rows in
               this table."
       ::= { dsx0BundleEntry 4 }

   -- The DS0 Bonding Group

   -- Implementation of this group is optional for all
   -- systems that use a DS0Bundle Interface.

   -- The DS0 Bonding Group consists of one table:
   --    DS0 Bonding Table

   -- The DS0 Bonding Table

   dsx0BondingTable OBJECT-TYPE
       SYNTAX  SEQUENCE OF Dsx0BondingEntry
       MAX-ACCESS  not-accessible
       STATUS  current
       DESCRIPTION
               "The DS0 Bonding table."
       ::= { ds0Bundle 1 }

   dsx0BondingEntry OBJECT-TYPE
       SYNTAX  Dsx0BondingEntry
       MAX-ACCESS  not-accessible
       STATUS  current
       DESCRIPTION
               "An entry in the DS0 Bonding table.  There is a
               row in this table for each DS0Bundle interface."
       INDEX   { ifIndex }
       ::= { dsx0BondingTable 1 }

   Dsx0BondingEntry ::=
       SEQUENCE {
           dsx0BondMode            INTEGER,
           dsx0BondStatus          INTEGER,
           dsx0BondRowStatus       RowStatus
   }

   dsx0BondMode OBJECT-TYPE
       SYNTAX  INTEGER {
                   none(1),
                   other(2),
                   mode0(3),
                   mode1(4),
                   mode2(5),



RFC 2494                DSO MIB / DSOBUNDLE MIB             January 1999


                   mode3(6)
       }
       MAX-ACCESS  read-create
       STATUS  current
       DESCRIPTION
               "This object indicates which BONDing mode is used,
               if any, for a ds0Bundle.  Mode0 provides parameter
               and number exchange with no synchronization.  Mode
               1 provides parameter and number exchange.  Mode 1
               also provides synchronization during
               initialization but does not include inband
               monitoring.  Mode 2 provides all of the above plus
               inband monitoring.  Mode 2 also steals 1/64th of
               the bandwidth of each channel (thus not supporting
               n x 56/64 kbit/s data channels for most values of
               n). Mode 3 provides all of the above, but also
               provides n x 56/64 kbit/s data channels.  Most
               common implementations of Mode 3 add an extra
               channel to support the inband monitoring overhead.
               ModeNone should be used when the interface is not
               performing bandwidth-on-demand."
       ::= { dsx0BondingEntry 1 }

   dsx0BondStatus OBJECT-TYPE
       SYNTAX  INTEGER {
                   idle(1),
                   callSetup(2),
                   dataTransfer(3)
       }
       MAX-ACCESS  read-only
       STATUS  current
       DESCRIPTION
               "This object indicates the current status of the
               bonding call using this ds0Bundle. idle(1) should
               be used when the bonding mode is set to none(1)."
       ::= { dsx0BondingEntry 2 }

   dsx0BondRowStatus OBJECT-TYPE
       SYNTAX  RowStatus
       MAX-ACCESS  read-create
       STATUS  current
       DESCRIPTION
               "This object is used to create new rows in this
               table, modify existing rows, and to delete
               existing rows."
       ::= { dsx0BondingEntry 3 }





RFC 2494                DSO MIB / DSOBUNDLE MIB             January 1999


   -- conformance information

   ds0BundleConformance OBJECT IDENTIFIER ::= { ds0Bundle 4 }

   ds0BundleGroups      OBJECT IDENTIFIER
       ::= { ds0BundleConformance 1 }

   ds0BundleCompliances OBJECT IDENTIFIER
       ::= { ds0BundleConformance 2 }



   -- compliance statements

   ds0BundleCompliance MODULE-COMPLIANCE
       STATUS  current
       DESCRIPTION
               "The compliance statement for DS0Bundle
               interfaces."
       MODULE  -- this module
           MANDATORY-GROUPS {ds0BundleConfigGroup }

           GROUP       ds0BondingGroup
           DESCRIPTION
               "Implementation of this group is optional for all
               systems that attach to a DS0Bundle Interface."

           OBJECT      dsx0BundleRowStatus
           SYNTAX      INTEGER {
                           active(1),
                           createAndGo(4),
                           destroy(6)
                       }
           MIN-ACCESS  read-only
           DESCRIPTION
               "The agent is not required to support a SET
               operation to this object, and only three of the
               six enumerated values for the RowStatus textual
               convention need be supported.  Only supporting
               createAndGo for a creation process prevents the
               manager from creating an inactive row in the
               ds0BundleTable.  Inactive rows in the
               ds0BundleTable do not make sense."

           OBJECT      dsx0BundleCircuitIdentifier
           MIN-ACCESS  read-only
           DESCRIPTION
               "The agent is not required to support a SET



RFC 2494                DSO MIB / DSOBUNDLE MIB             January 1999


               operation to this object."

                   ::= { ds0BundleCompliances 1 }

               -- units of conformance

               ds0BondingGroup  OBJECT-GROUP
                   OBJECTS { dsx0BondMode,
                             dsx0BondStatus,
                             dsx0BondRowStatus }
                   STATUS  current
                   DESCRIPTION
                           "A collection of objects providing
                           configuration information applicable
                           to all DS0 interfaces."
       ::= { ds0BundleGroups 1 }
   ds0BundleConfigGroup  OBJECT-GROUP
       OBJECTS { dsx0BundleNextIndex,
                 dsx0BundleIfIndex,
                 dsx0BundleCircuitIdentifier,
                 dsx0BundleRowStatus }
       STATUS  current
       DESCRIPTION
               "A collection of objects providing the ability to
               create a new ds0Bundle in the ifTable as well as
               configuration information about the ds0Bundle."
       ::= { ds0BundleGroups 2 }
   END

6.  Intellectual Property

   The IETF takes no position regarding the validity or scope of any
   intellectual property or other rights that might be claimed to
   pertain to the implementation or use of the technology described in
   this document or the extent to which any license under such rights
   might or might not be available; neither does it represent that it
   has made any effort to identify any such rights.  Information on the
   IETF's procedures with respect to rights in standards-track and
   standards-related documentation can be found in BCP-11.  Copies of
   claims of rights made available for publication and any assurances of
   licenses to be made available, or the result of an attempt made to
   obtain a general license or permission for the use of such
   proprietary rights by implementors or users of this specification can
   be obtained from the IETF Secretariat.







RFC 2494                DSO MIB / DSOBUNDLE MIB             January 1999


   The IETF invites any interested party to bring to its attention any
   copyrights, patents or patent applications, or other proprietary
   rights which may cover technology that may be required to practice
   this standard.  Please address the information to the IETF Executive
   Director.

7.  Acknowledgments

   This document was produced by the Trunk MIB Working Group.

8.  References

   [1]  Harrington, D., Presuhn, R., and B. Wijnen, "An Architecture for
        Describing SNMP Management Frameworks", RFC 2271, January 1998.

   [2]  Rose, M., and K. McCloghrie, "Structure and Identification of
        Management Information for TCP/IP-based Internets", STD 16, RFC
        1155, May 1990.

   [3]  Rose, M., and K. McCloghrie, "Concise MIB Definitions", STD 16,
        RFC 1212, March 1991.

   [4]  Rose, M., "A Convention for Defining Traps for use with the
        SNMP", RFC 1215, March 1991.

   [5]  Case, J., McCloghrie, K., Rose, M., and S. Waldbusser,
        "Structure of Management Information for Version 2 of the Simple
        Network Management Protocol (SNMPv2)", RFC 1902, January 1996.

   [6]  Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Textual
        Conventions for Version 2 of the Simple Network Management
        Protocol (SNMPv2)", RFC 1903, January 1996.

   [7]  Case, J., McCloghrie, K., Rose, M., and S. Waldbusser,
        "Conformance Statements for Version 2 of the Simple Network
        Management Protocol (SNMPv2)", RFC 1904, January 1996.

   [8]  Case, J., Fedor, M., Schoffstall, M., and J. Davin, "Simple
        Network Management Protocol", STD 15, RFC 1157, May 1990.

   [9]  Case, J., McCloghrie, K., Rose, M., and S. Waldbusser,
        "Introduction to Community-based SNMPv2", RFC 1901, January
        1996.

   [10] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser,
        "Transport Mappings for Version 2 of the Simple Network
        Management Protocol (SNMPv2)", RFC 1906, January 1996.




RFC 2494                DSO MIB / DSOBUNDLE MIB             January 1999


   [11] Case, J., Harrington D., Presuhn R., and B. Wijnen, "Message
        Processing and Dispatching for the Simple Network Management
        Protocol (SNMP)", RFC 2272, January 1998.

   [12] Blumenthal, U., and B. Wijnen, "User-based Security Model (USM)
        for version 3 of the Simple Network Management Protocol
        (SNMPv3)", RFC 2274, January 1998.

   [13] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Protocol
        Operations for Version 2 of the Simple Network Management
        Protocol (SNMPv2)", RFC 1905, January 1996.

   [14] Levi, D., Meyer, P., and B. Stewart, "SNMPv3 Applications", RFC
        2273, January 1998.

   [15] Wijnen, B., Presuhn, R., and K. McCloghrie, "View-based Access
        Control Model (VACM) for the Simple Network Management Protocol
        (SNMP)", RFC 2275, January 1998.

   [16] McCloghrie, K. and F. Kastenholz, "The Interfaces Group MIB
        using SMIv2", RFC 2233, November 1997.

   [17] Fowler D., "Definitions of Managed Objects for the DS1, E1, DS2,
        and E2 Interface Types", RFC 2495, January 1999.

   [18] Fowler, D., "Definitions of Managed Objects for the DS3/E3
        Interface Types", RFC 2496, January 1999.

   [19] Brown, T., and K. Tesink, "Definitions of Managed Objects for
        the SONET/SDH Interface Type", Work in Progress.

   [20] Sharp, H. (Editor), "Interoperability Requirements for Nx56/64
        kbit/s Calls", BONDING Spec Version 1.0, BONDING Consortium,
        Sept 1992.

9.  Security Considerations

   SNMPv1 by itself is such an insecure environment.  Even if the
   network itself is secure (for example by using IPSec), even then,
   there is no control as to who on the secure network is allowed to
   access and GET (read) the objects in this MIB.

   It is recommended that the implementors consider the security
   features as provided by the SNMPv3 framework.  Specifically, the use
   of the User-based Security Model RFC 2274 [12] and the View-based
   Access Control Model RFC 2275 [15] is recommended.





RFC 2494                DSO MIB / DSOBUNDLE MIB             January 1999


   It is then a customer/user responsibility to ensure that the SNMP
   entity giving access to an instance of this MIB, is properly
   configured to give access to those objects only to those principals
   (users) that have legitimate rights to access them.

   Setting the following objects to an inappropriate value can cause
   loss of traffic.  In the case of dsx0RobbedBitSignalling, for
   example, the nature of the traffic flowing on the DS0 can be
   affected.
      dsx0RobbedBitSignalling
      dsx0IdleCode
      dsx0SeizedCode
      dsx0TransmitCodesEnable
      dsx0BundleRowStatus
      dsx0BondMode
      dsx0BondRowStatus

   Setting the following objects is mischievous, but not harmful to
   traffic.
      dsx0CircuitIdentifier
      dsx0BundleNextIndex

10.  Author's Address

   David Fowler
   Newbridge Networks
   600 March Road
   Kanata, Ontario, Canada K2K 2E6

   Phone: (613) 599-3600, ext 6559
   EMail: davef@newbridge.com




















RFC 2494                DSO MIB / DSOBUNDLE MIB             January 1999


11.  Full Copyright Statement

   Copyright (C) The Internet Society (1999).  All Rights Reserved.

   This document and translations of it may be copied and furnished to
   others, and derivative works that comment on or otherwise explain it
   or assist in its implementation may be prepared, copied, published
   and distributed, in whole or in part, without restriction of any
   kind, provided that the above copyright notice and this paragraph are
   included on all such copies and derivative works.  However, this
   document itself may not be modified in any way, such as by removing
   the copyright notice or references to the Internet Society or other
   Internet organizations, except as needed for the purpose of
   developing Internet standards in which case the procedures for
   copyrights defined in the Internet Standards process must be
   followed, or as required to translate it into languages other than
   English.

   The limited permissions granted above are perpetual and will not be
   revoked by the Internet Society or its successors or assigns.

   This document and the information contained herein is provided on an
   "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
   TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
   BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
   HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
   MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.