IPv6 Backbone RouterCisco Systems, Inc.Building D45 Allee des Ormes - BP1200MOUGINS - Sophia Antipolis06254France+33 497 23 26 34pthubert@cisco.comBlue Meadow NetworkingSaratogaCA95070United States of Americacharliep@computer.orgCisco Systems, Inc.Building D45 Allee des Ormes - BP1200MOUGINS - Sophia Antipolis06254France+33 497 23 26 20elevyabe@cisco.com
Internet
6lo
This document updates RFCs 6775 and 8505 in order to enable
proxy services for IPv6 Neighbor Discovery by Routing Registrars
called "Backbone Routers".
Backbone Routers are placed along the wireless edge of a backbone and
federate multiple wireless links to form a single Multi-Link
Subnet (MLSN).
Status of This Memo
This is an Internet Standards Track document.
This document is a product of the Internet Engineering Task Force
(IETF). It represents the consensus of the IETF community. It has
received public review and has been approved for publication by
the Internet Engineering Steering Group (IESG). Further
information on Internet Standards is available in Section 2 of
RFC 7841.
Information about the current status of this document, any
errata, and how to provide feedback on it may be obtained at
.
Copyright Notice
Copyright (c) 2020 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
() in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with
respect to this document. Code Components extracted from this
document must include Simplified BSD License text as described in
Section 4.e of the Trust Legal Provisions and are provided without
warranty as described in the Simplified BSD License.
Table of Contents
. Introduction
. Terminology
. Requirements Language
. New Terms
. Abbreviations
. Background
. Overview
. Updating RFCs 6775 and 8505
. Access Link
. Route-Over Mesh
. The Binding Table
. Primary and Secondary 6BBRs
. Using Optimistic DAD
. Multi-Link Subnet Considerations
. Optional 6LBR Serving the Multi-Link Subnet
. Using IPv6 ND over the Backbone Link
. Routing Proxy Operations
. Bridging Proxy Operations
. Creating and Maintaining a Binding
. Operations on a Binding in Tentative State
. Operations on a Binding in Reachable State
. Operations on a Binding in Stale State
. Registering Node Considerations
. Security Considerations
. Protocol Constants
. IANA Considerations
. Normative References
. Informative References
. Possible Future Extensions
. Applicability and Requirements Served
Acknowledgments
Authors' Addresses
Introduction
Ethernet bridging per IEEE Std 802.1
provides an efficient and reliable broadcast service for wired
networks; applications and protocols have been built that heavily
depend on that feature for their core operation. Unfortunately,
Low-Power and Lossy Networks (LLNs) and local wireless networks generally
do not provide the broadcast capabilities of Ethernet bridging in an
economical fashion.
As a result, protocols designed for bridged networks that rely
on multicast and broadcast often exhibit disappointing behaviors
when employed unmodified on a local wireless medium (see
).
Wi-Fi Access Points (APs)
deployed in an Extended Service Set (ESS) act as Ethernet bridges
, with the property that the bridging
state is established at the time of association. This ensures
connectivity to the end node (the Wi-Fi Station (STA)) and protects the wireless medium
against broadcast-intensive transparent bridging reactive lookups.
In other words, the association process is used to register the link-layer
address of the STA to the AP. The AP subsequently proxies the
bridging operation and does not need to forward the broadcast lookups
over the radio.
In the same way as transparent bridging, the IPv6
Neighbor Discovery (IPv6 ND) protocol
is a reactive protocol, based on multicast
transmissions to locate an on-link correspondent and ensure the
uniqueness of an IPv6 address. The mechanism for Duplicate Address
Detection (DAD) was designed for
the efficient broadcast operation of Ethernet bridging.
Since broadcast can be unreliable over wireless media, DAD often
fails to discover duplications
. In practice, the fact that IPv6 addresses very rarely conflict is mostly attributable to the entropy of the 64-bit Interface IDs as opposed to the successful operation of the IPv6 ND DAD and resolution mechanisms.
The IPv6 ND Neighbor Solicitation (NS) message
is used for DAD and address lookup when a node moves or wakes up and
reconnects to the wireless network. The NS message is targeted to a
Solicited-Node Multicast Address (SNMA) and
should, in theory, only reach a very small group of nodes. But, in
reality, IPv6 multicast messages are typically broadcast on the
wireless medium, so they
are processed by most of the wireless nodes over the subnet (e.g., the
ESS fabric) regardless of how few of the nodes are subscribed to the
SNMA. As a result, IPv6 ND address lookups and DADs over a large
wireless network and/or LLN can consume enough
bandwidth to cause a substantial degradation to the unicast traffic
service.
Because IPv6 ND messages sent to the SNMA group are broadcast at the
radio link layer, wireless nodes that do not belong to the SNMA group
still have to keep their radio turned on to listen to multicast NS
messages, which is a waste of energy for them. In order to
reduce their power consumption, certain battery-operated devices such
as Internet of Things (IoT) sensors and smartphones ignore some of the broadcasts, making
IPv6 ND operations even less reliable.
These problems can be alleviated by reducing the IPv6 ND broadcasts
over wireless access links. This has been done by splitting the broadcast
domains and routing between subnets. At the extreme, this can be done by assigning
a /64 prefix to each wireless node (see ).
But deploying a single large subnet can still be attractive to avoid
renumbering in situations that involve large numbers of devices and mobility
within a bounded area.
A way to reduce the propagation of IPv6 ND broadcast in the wireless domain
while preserving a large single subnet is to form a Multi-Link Subnet (MLSN).
Each link in the MLSN, including the backbone, is its own broadcast domain.
A key property of MLSNs is that link-local unicast traffic, link-scope multicast, and traffic with a hop limit of 1 will not transit to nodes in the same subnet on a different link, which is something that may produce unexpected behavior in software that expects a subnet to be entirely contained within a single link.
This specification considers a special type of MLSN with a central backbone that federates edge (LLN) links, with each link providing its own protection against rogue access and tempering or replaying packets. In particular, the use of classical IPv6 ND on the backbone requires that the all nodes are trusted and that rogue access
to the backbone is prevented at all times (see ).
In that particular topology, ND proxies can be placed at the boundary of the edge links and the backbone to handle IPv6 ND on behalf of Registered Nodes and to forward IPv6 packets back and forth.
The ND proxy enables the continuity of IPv6 ND operations beyond the backbone and enables communication using Global or Unique Local Addresses between any pair of nodes in the MLSN.
The 6LoWPAN Backbone Router (6BBR) is a Routing Registrar that provides ND proxy services.
A 6BBR acting as a Bridging Proxy provides an ND proxy function with Layer 2 continuity and can be
collocated with a Wi-Fi AP as prescribed by IEEE Std 802.11 . A 6BBR acting as a Routing Proxy is applicable to any type of LLN, including LLNs that cannot be bridged onto the backbone, such as IEEE Std 802.15.4 .
Knowledge of which address to proxy can be obtained by snooping the
IPv6 ND protocol (see ), but it has been found to be unreliable.
An IPv6 address may not be discovered immediately due to a packet loss or if a "silent" node
is not currently using one of its addresses. A change of state (e.g.,
due to movement) may be missed or misordered, leading to unreliable
connectivity and incomplete knowledge of the state of the network.
With this specification, the address to be proxied is signaled explicitly through a registration process.
A 6LoWPAN Node (6LN) registers all of its IPv6 addresses using NS messages with an Extended Address Registration Option (EARO) as specified in to a 6LoWPAN Router (6LR) to which it is directly attached.
If the 6LR is a 6BBR, then the 6LN is both the Registered Node and the Registering Node. If not, then the 6LoWPAN Border Router (6LBR) that serves the LLN proxies the registration to the 6BBR. In that case, the 6LN is the Registered Node and the 6LBR is the Registering Node.
The 6BBR performs IPv6 ND operations on its backbone interface on behalf of the 6LNs that have Registered Addresses on its LLN interfaces, without the need of a broadcast over the wireless medium.
A Registering Node that resides on the backbone does not register to the SNMA groups associated to its Registered Addresses and defers to the 6BBR to answer or preferably forward the corresponding multicast packets to it as unicast.
TerminologyRequirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED",
"MAY", and "OPTIONAL" in this document are to be interpreted as
described in BCP 14
when, and only when, they appear in all capitals, as shown here.
New Terms
This document introduces the following terminology:
Federated:
A subnet that comprises a backbone, and one or more (wireless)
access links, is said to be federated into one MLSN.
The ND proxy operation of 6BBRs over the backbone extends IPv6 ND operation over the access links.
Sleep Proxy:
A 6BBR acts as a Sleep Proxy if it answers IPv6 ND NSs over the backbone on behalf of the Registering
Node that is in a sleep state and that cannot answer in due time.
Routing Proxy:
A Routing Proxy provides IPv6 ND proxy functions and enables the
MLSN operation over federated links that may not be compatible for
bridging. The Routing Proxy advertises its own link-layer
address as the Target Link-Layer Address (TLLA) in the proxied Neighbor Advertisements (NAs)
over the backbone and routes
at the network layer between the federated links.
Bridging Proxy:
A Bridging Proxy provides IPv6 ND proxy functions while preserving
forwarding continuity at the link layer.
In
that case, the link-layer address and the mobility of the Registering Node is
visible across the bridged backbone. The Bridging Proxy advertises
the link-layer address of the Registering Node in the TLLAO in the proxied NAs
over the backbone, and it proxies ND for all unicast addresses including link-local addresses.
Instead of replying on behalf of the Registering Node, a Bridging Proxy
will preferably forward the NS(Lookup) and Neighbor Unreachability Detection (NUD) messages that target the
Registered Address to the Registering Node as unicast frames, so it can
respond in its own.
Binding Table:
The Binding Table is an abstract database that is maintained by the
6BBR to store the state associated with its registrations.
Binding:
A Binding is an abstract state associated to one registration; in
other words, it's associated to one entry in the Binding Table.
Abbreviations This document uses the following abbreviations:
6BBR:
6LoWPAN Backbone Router
6LBR:
6LoWPAN Border Router
6LN:
6LoWPAN Node
6LR:
6LoWPAN Router
AP:
Access Point
ARO:
Address Registration Option
DAC:
Duplicate Address Confirmation
DAD:
Duplicate Address Detection
DAR:
Duplicate Address Request
DODAG:
Destination-Oriented Directed Acyclic Graph
EARO:
Extended Address Registration Option
EDAC:
Extended Duplicate Address Confirmation
EDAR:
Extended Duplicate Address Request
ESS:
Extended Service Set
LLA:
Link-Layer Address
LLN:
Low-Power and Lossy Network
MLSN:
Multi-Link Subnet
MTU:
Maximum Transmission Unit
NA:
Neighbor Advertisement
NCE:
Neighbor Cache Entry
ND:
Neighbor Discovery
NS:
Neighbor Solicitation
NUD:
Neighbor Unreachability Detection
ODAD:
Optimistic DAD
RA:
Router Advertisement
ROVR:
Registration Ownership Verifier
RPL:
Routing Protocol for LLNs
RS:
Router Solicitation
SLLAO:
Source Link-Layer Address Option
SNMA:
Solicited-Node Multicast Address
STA:
Station
TID:
Transaction ID
TLLAO:
Target Link-Layer Address Option
Background
In this document, readers will encounter terms and concepts
that are discussed in the following documents:
Classical IPv6 ND:
"Neighbor Discovery for IP version 6 (IPv6)" ,
"IPv6 Stateless Address Autoconfiguration" , and
"Optimistic Duplicate Address Detection (DAD) for IPv6" ;
IPv6 ND over multiple links:
"Neighbor Discovery Proxies (ND Proxy)"
and
"Multi-Link Subnet Issues" ;
6LoWPAN:
"Problem Statement and Requirements for
IPv6 over Low-Power Wireless Personal Area Network (6LoWPAN)
Routing" ; and
6LoWPAN ND:
Neighbor Discovery Optimization for IPv6 over Low-Power
Wireless Personal Area Networks (6LoWPANs) ,
"Registration Extensions for IPv6 over Low-Power Wireless Personal Area Network (6LoWPAN) Neighbor Discovery" ,
and
"Address-Protected Neighbor Discovery for Low-Power and Lossy Networks"
.
Overview This section and its subsections present a non-normative high-level view of
the operation of the 6BBR. The following sections cover the normative part.
illustrates a Backbone Link that federates a
collection of LLNs as a single IPv6 subnet, with a number of 6BBRs
providing ND proxy services to their attached LLNs.
The LLN may be a hub-and-spoke access link such as (Low-Power)
IEEE Std 802.11 (Wi-Fi)
and IEEE Std 802.15.1 (Bluetooth)
or a mesh-under or a route-over network .
The proxy state can be distributed across multiple 6BBRs attached to
the same backbone.
The main features of a 6BBR are as follows:
MLSN functions (provided by the 6BBR on the
backbone) performed on behalf of Registered Nodes
Routing Registrar services that reduce multicast within the LLN:
- Binding Table management
- failover, e.g., due to mobility
Each Backbone Router (6BBR) maintains a data structure for its
Registered Addresses called a Binding Table. The abstract data that
is stored in the Binding Table includes the Registered Address; anchor information on the Registering Node such as the connecting interface, link-local address, and link-layer address (LLA) of the Registering Node on that interface; the EARO including ROVR and TID; a state that can be either Reachable, Tentative, or Stale; and other information such as a trust level that may be configured, e.g., to protect a server. The combined Binding Tables
of all the 6BBRs on a backbone form a distributed database of Registered Nodes
that reside in the LLNs or on the IPv6 Backbone.
Unless otherwise configured, a 6BBR does the following:
Creates a new entry in a Binding Table for a newly
Registered Address and ensures that the address is not
duplicated over the backbone.
Advertises a Registered Address over the backbone using an NA message as
either unsolicited or a response to an NS message. This includes
joining the multicast group associated to the SNMA derived from the
Registered Address, as specified in
, over the backbone.
The 6BBR MAY respond immediately as a proxy in lieu of the Registering Node, e.g., if the Registering Node has a sleep cycle that the 6BBR does not want to interrupt or if the 6BBR has a recent state that is deemed fresh enough to permit the proxied response. It is preferred, though, that the 6BBR checks whether the Registering Node is still responsive on the Registered Address. To that effect:
- as a Bridging Proxy:
the 6BBR forwards the multicast DAD and address lookup messages as a unicast link-layer frame to the link-layer address of the Registering Node that matches the target in the ND message; the Neighbor Unreachability Detection (NUD) message is unicast and is forwarded as is. In all cases, the goal is to let the Registering Node answer with the ND Message and options that it sees fit.
- as a Routing Proxy:
the 6BBR checks the liveliness of the Registering Node, e.g., using a NUD verification, before answering on its behalf.
Delivers packets arriving from the LLN, using Neighbor Solicitation
messages to look up the destination over the backbone.
Forwards or bridges packets between the LLN and the backbone.
Verifies liveness for a registration, when needed.
The first of these functions enables the 6BBR to fulfill its
role as a Routing Registrar for each of its attached LLNs.
The remaining functions fulfill the role of the 6BBRs as the
border routers that federate the Multi-Link IPv6 Subnet.
The operation of IPv6 ND and ND proxy are not mutually exclusive on the backbone, meaning that nodes attached to the backbone and using IPv6 ND can transparently interact with 6LNs that rely on a 6BBR to ND proxy for them, whether the 6LNs are reachable over an LLN or directly attached to the backbone.
The registration mechanism used to learn addresses to be proxied may
coexist in a 6BBR with a proprietary snooping or the traditional bridging functionality of an AP, in order to support legacy LLN nodes that do not support this specification.
The registration to a proxy service uses an NS/NA exchange with EARO.
The 6BBR operation resembles that of a
Mobile IPv6 (MIPv6) Home Agent (HA).
The combination of a 6BBR and a MIPv6 HA enables full mobility
support for 6LNs, inside and outside the links that form the subnet.
6BBRs perform IPv6 ND functions over the backbone as follows:
The EARO is used in IPv6 ND exchanges over
the backbone between the 6BBRs to help distinguish duplication from movement.
Extended Duplicate Address Messages (EDAR and EDAC) may also be
used to communicate with a 6LBR, if one is present.
Address duplication is detected using the ROVR field.
Conflicting registrations to different 6BBRs for the same
Registered Address are resolved using the TID field, which forms an order
of registrations.
The LLA that the 6BBR advertises for the
Registered Address on behalf of the Registered Node over the
backbone can belong to the Registering Node; in that case, the 6BBR
(acting as a Bridging Proxy (see ))
bridges the unicast packets. Alternatively, the LLA can be that
of the 6BBR on the backbone interface, in which case, the 6BBR
(acting as a Routing Proxy (see ))
receives the unicast packets at Layer 3 and routes over.
Updating RFCs 6775 and 8505
This specification adds the EARO as a possible option in RS, NS(DAD),
and NA messages over the backbone.
This document specifies the use of those ND messages by 6BBRs
over the backbone, at a high level in and in more
detail in .
This specification allows the deployment of a 6LBR on the backbone where EDAR and
EDAC messages coexist with classical ND. It also adds the capability to insert IPv6 ND options in the EDAR and EDAC messages.
A 6BBR acting as a 6LR
for the Registered Address can insert an SLLAO in the EDAR to the 6LBR in
order to avoid causing a multicast NS(lookup) back. This enables the 6LBR to store the link-layer
address associated with the Registered Address on a link and to serve as a
mapping server as described in
.
This specification allows an address to be registered to more than one
6BBR. Consequently, a 6LBR that is deployed on the backbone MUST be capable
of maintaining state for each of the 6BBRs that have registered with the same
TID and same ROVR.
Access Link
The simplest MLSN topology from the Layer 3 perspective occurs
when the wireless network appears as a single-hop hub-and-spoke network as
shown in . The Layer 2 operation may effectively
be hub-and-spoke (e.g., Wi-Fi) or mesh-under, with a Layer 2 protocol
handling the complex topology.
illustrates a flow where 6LN forms an IPv6
address and registers it to a 6BBR acting as a 6LR
. The 6BBR applies Optimistic Duplicate Address Detection (ODAD) (see
) to the Registered Address to enable
connectivity while the message flow is still in progress.
In this example, a 6LBR is deployed on the Backbone Link to serve the whole
subnet, and EDAR/EDAC messages are used in combination with DAD to enable
coexistence with IPv6 ND over the backbone.
The RS sent initially by the 6LN (e.g., a Wi-Fi STA) is transmitted as a multicast, but
since it is intercepted by the 6BBR, it is never effectively broadcast.
The multiple arrows associated to the ND messages on the backbone denote a
real Layer 2 broadcast.
Route-Over Mesh
A more complex MLSN topology occurs when the wireless network
appears as a Layer 3 mesh network as shown in .
A so-called route-over routing protocol exposes routes between 6LRs towards
both 6LRs and 6LNs, and a 6LBR acts as the Root of the Layer 3 mesh network and
proxy-registers the LLN addresses to the 6BBR.
illustrates IPv6 signaling that
enables a 6LN (the Registered Node) to form a Global or a Unique Local Address and register it to the 6LBR that serves its LLN using and a neighboring 6LR as relay.
The 6LBR (the Registering Node) then proxies the registration to the 6BBR to obtain ND proxy services from the 6BBR.
The RS sent initially by the 6LN is transmitted as a multicast and contained within 1-hop broadcast range where hopefully a 6LR is found. The 6LR is expected to be already connected to the LLN and capable of reaching the 6LBR, which is possibly multiple hops away, using unicast messages.
As a non-normative example of a route-over mesh, the
IPv6 over the TSCH mode of IEEE 802.15.4e (6TiSCH) architecture
suggests using the RPL and collocating the RPL
root with a 6LBR that serves the LLN. The 6LBR is also either collocated with or directly connected to the 6BBR over an IPv6 link.
The Binding Table
Addresses in an LLN that are reachable from the backbone by way of the 6BBR
function must be registered to that 6BBR, using an NS(EARO) with the R flag
set . The 6BBR answers with an NA(EARO)
and maintains a state for the registration in an abstract
Binding Table.
An entry in the Binding Table is called a "Binding".
A Binding may be in Tentative, Reachable, or Stale state.
The 6BBR uses a combination of and IPv6 ND over the
backbone to advertise the registration and avoid a duplication.
Conflicting registrations are solved by the 6BBRs transparently to the
Registering Nodes.
Only one 6LN may register a given address, but the address may be registered
to multiple 6BBRs for higher availability.
Over the LLN, Binding Table management is as follows:
De-registrations (newer TID, same ROVR, null Lifetime) are
accepted with a status code of 4 ("Removed"); the entry is deleted.
Newer registrations (newer TID, same ROVR, non-null Lifetime) are
accepted with a status code of 0 ("Success"); the Binding is updated
with the new TID, the Registration Lifetime, and the Registering
Node. In Tentative state, the EDAC response
is held and may be overwritten; in other states, the
Registration Lifetime timer is restarted, and the entry is placed
in Reachable state.
Identical registrations (same TID, same ROVR) from the same
Registering Node are accepted with a status code of 0 ("Success").
In Tentative state, the response is held and may be overwritten,
but the response is eventually produced, carrying
the result of the DAD process.
Older registrations (older TID, same ROVR) from the same
Registering Node are discarded.
Identical and older registrations (not-newer TID, same ROVR) from
a different Registering Node are rejected with a status code of 3
("Moved"); this may be rate-limited to avoid undue interference.
Any registration for the same address but with a different
ROVR is rejected with a status code of 1 ("Duplicate Address").
The operation of the Binding Table is specified in detail in .
Primary and Secondary 6BBRs
A Registering Node MAY register the same address to more than one 6BBR,
in which case, the Registering Node uses the same EARO in all the parallel
registrations.
On the other hand, there is no provision in 6LoWPAN ND for a 6LN (acting
as Registered Node) to select its 6LBR (acting as Registering Node), so it
cannot select more than one either.
To allow for this, NS(DAD) and NA messages with an EARO received over the
backbone that indicate an identical Binding in another 6BBR (same Registered
Address, same TID, same ROVR) are silently ignored except for the purpose of
selecting the primary 6BBR for that registration.
A 6BBR may be either primary or secondary. The primary is the 6BBR
that has the highest 64-bit Extended Unique Identifier (EUI-64)
address of all the 6BBRs that share a registration for the same
Registered Address, with the same ROVR and same Transaction ID, and the
EUI-64 address is considered an unsigned 64-bit integer.
A given 6BBR can be primary for a given address and secondary for another
address, regardless of whether or not the addresses belong to the same 6LN.
In the following sections, it is expected that an NA will be sent over the
backbone only if the node is primary or does not support the concept of
primary. More than one 6BBR claiming or defending an address generates
unwanted traffic, but there is no reachability issue since all 6BBRs provide
reachability from the backbone to the 6LN.
If a Registering Node loses connectivity to its 6BBR or one of the 6BBRs to which
it registered an address, it retries the registration to the (one or more)
available 6BBR(s). When doing that, the Registering Node MUST increment the
TID in order to force the migration of the state to the new 6BBR and
the reselection of the primary 6BBR if it is the node that was lost.
Using Optimistic DAD
ODAD specifies how an IPv6 address can be used before completion of
DAD. ODAD guarantees that this behavior
will not cause harm if the new address is a duplicate.
Support for ODAD avoids delays in installing the Neighbor Cache Entry (NCE)
in the 6BBRs and the default router, enabling immediate connectivity
to the Registered Node. As shown in , if the
6BBR is aware of the LLA of a router, then the
6BBR sends a Router Solicitation (RS), using the Registered Address as
the IP Source Address, to the known router(s). The RS is sent
without an SLLAO, to avoid invalidating a
preexisting NCE in the router.
Following ODAD, the router may then send a unicast RA to the Registered
Address, and it may resolve that address using an NS(Lookup) message.
In response, the 6BBR sends an NA with an EARO and the Override flag
that is not set.
The router can then determine the freshest EARO in case of
conflicting NA(EARO) messages, using the method described in
.
If the NA(EARO) is the freshest answer, the default router creates a
Binding with the SLLAO of the 6BBR (in Routing Proxy mode) or that of the
Registering Node (in Bridging Proxy mode), so traffic from/to the
Registered Address can flow immediately.
Multi-Link Subnet Considerations
The backbone and the federated LLN links are considered to be different
links in the MLSN, even if multiple LLNs are attached to
the same 6BBR. ND messages are link-scoped and are not forwarded by the
6BBR between the backbone and the LLNs, though some packets may be
reinjected in Bridging Proxy mode (see ).
Legacy nodes located on the backbone expect that the subnet is deployed
within a single link and that there is a common Maximum Transmission Unit
(MTU) for intra-subnet communication: the Link MTU.
They will not perform the IPv6 Path MTU Discovery
for a destination within the subnet. For that reason, the MTU MUST have
the same value on the backbone and on all federated LLNs in the MLSN. As a
consequence, the 6BBR MUST use the same MTU value in RAs over the backbone
and in the RAs that it transmits toward the LLN links.
Optional 6LBR Serving the Multi-Link Subnet
A 6LBR can be deployed to serve the whole MLSN as shown in . It may be attached to the
backbone, in which case it can be discovered by its capability advertisement
(see ) in RA messages.
When a 6LBR is present, the 6BBR uses an EDAR/EDAC message
exchange with the 6LBR to check if the new registration corresponds to a duplication or a movement.
This is done prior to the NS(DAD) process, which may be avoided if
the 6LBR already maintains a conflicting state for the Registered Address.
If this registration is a duplicate or not the freshest, then the 6LBR
replies with an EDAC message with a status code of 1 ("Duplicate Address") or 3 ("Moved"), respectively.
If this registration is the freshest, then the 6LBR replies with a status
code of 0 ("Success"). In that case, if this registration is fresher than an existing
registration for another 6BBR, then the 6LBR also sends an asynchronous
EDAC with a status code of 4 ("Removed") to the older 6BBR.
The EDAR message SHOULD carry the SLLAO used in NS messages by the 6BBR
for that Binding, and the EDAC message SHOULD carry the Target Link-Layer
Address Option (TLLAO) associated with the currently accepted registration.
This enables a 6BBR to locate
the new position of a mobile 6LN in the case of a Routing Proxy operation
and opens the capability for the 6LBR to serve as a mapping server in the
future.
Note that if link-local addresses are registered, then the scope of
uniqueness on which the address duplication is checked is the total
collection of links that the 6LBR serves, as opposed to the sole link on
which the link-local address is assigned.
Using IPv6 ND over the Backbone Link
On the backbone side, the 6BBR MUST join the SNMA group corresponding
to a Registered Address as soon as it creates a Binding for that
address and maintain that SNMA membership as long as it maintains the
registration.
The 6BBR uses either the SNMA or plain unicast to
defend the Registered Addresses in its Binding Table over the
backbone (as specified in ).
The 6BBR advertises and defends the Registered Addresses over the
Backbone Link using RS, NS(DAD), and NA messages with the Registered
Address as the Source or Target Address.
The 6BBR MUST place an EARO in the IPv6 ND messages that it generates
on behalf of the Registered Node. Note that an NS(DAD) does not
contain an SLLAO and cannot be confused with a proxy registration such as
performed by a 6LBR.
IPv6 ND operates as follows on the backbone:
specifies that an NA message generated as a proxy does not have the Override flag set in order to ensure that if the real owner is present on the link, its own NA will take precedence, and this NA does not update the NCE for the real owner if one exists.
A node that receives multiple NA messages updates an existing NCE only if the Override flag is set; otherwise, the node will probe the cached address.
When an NS(DAD) is received for a tentative address, which means that two nodes form the same address at nearly the same time, the node that first claimed the address cannot be detected per , and the address is abandoned.
In any case, indicates that a node never responds to a Neighbor Solicitation for a tentative address.
This specification adds information about proxied addresses that helps to sort out a duplication (different ROVR) from a movement (same ROVR, different TID); in the latter case, the older registration is sorted out from the fresher one (by comparing TIDs).
When a Registering Node moves from one 6BBR to the next, the 6BBRs send NA messages over the backbone to update existing NCEs. A node that receives multiple NA messages with an EARO option and the same ROVR MUST favor the NA with the freshest EARO over the others.
The new 6BBR MAY set the Override flag in the NA messages if it does not compete with the Registering Node for the NCE in backbone nodes. This is assured if the Registering Node is attached via an interface that cannot be bridged onto the backbone, making it impossible for the Registering Node to defend its own addresses there. This may also be signaled by the Registering Node through a protocol extension that is not in scope for this specification.
When the Binding is in Tentative state, the 6BBR acts as follows:
an NS(DAD) that indicates a duplication can still not be asserted for first come, but the situation can be avoided using a 6LBR on the backbone that will serialize the order of appearance of the address and ensure first-come, first-served.
an NS or an NA that denotes an older registration for the same Registered Node is not interpreted as a duplication as specified in Sections and of , respectively.
When the Binding is no longer in Tentative state, the 6BBR acts as follows:
an NS or an NA with an EARO that denotes a duplicate registration
(different ROVR) is answered with an NA message that carries an
EARO with a status code of 1 ("Duplicate Address"), unless the received
message is an NA that carries an EARO with a status code of 1
("Duplicate Address").
In any state, the 6BBR acts as follows:
an NS or an NA with an EARO that denotes an older registration (same ROVR) is answered with an NA message that carries an EARO with a status code of 3 ("Moved") to ensure that the Stale state is removed rapidly.
This behavior is specified in more detail in .
This specification enables proxy operation for the IPv6 ND resolution of
LLN devices, and a prefix that is used across an MLSN MAY be
advertised as on-link over the backbone. This is done for backward
compatibility with existing IPv6 hosts by setting the L flag in the Prefix
Information Option (PIO) of RA messages .
For movement involving a slow reattachment, the NUD procedure
defined in may timeout too
quickly. Nodes on the backbone SHOULD support
whenever possible.
Routing Proxy Operations
A Routing Proxy provides IPv6 ND proxy functions for Global and Unique
Local Addresses between the LLN and the backbone, but not for link-local
addresses. It operates as an IPv6 border router and provides a full
link-layer isolation.
In this mode, it is not required that the link-layer addresses of the 6LNs be
visible at Layer 2 over the backbone. Thus, it is useful when the messaging
over the backbone that is associated with wireless mobility becomes
expensive, e.g., when the Layer 2 topology is virtualized over a wide area
IP underlay.
This mode is definitely required when the LLN uses a link-layer address format
that is different from that on the backbone (e.g., EUI-64 versus EUI-48).
Since a 6LN may not be able to resolve an arbitrary destination in the
MLSN directly, a prefix that is used across a MLSN MUST NOT be advertised as
on-link in RA messages sent towards the LLN.
In order to maintain IP connectivity, the 6BBR installs a connected
host route to the Registered Address on the LLN interface, via the
Registering Node as identified by the source address and the SLLAO
in the NS(EARO) messages.
When operating as a Routing Proxy, the 6BBR MUST use its Layer 2
address on its backbone interface in the SLLAO of the RS messages and
the TLLAO of the NA messages that it generates to advertise the
Registered Addresses.
For each Registered Address, multiple peers on the backbone may
have resolved the address with the 6BBR link-layer address, maintaining that
mapping in their Neighbor Cache. The 6BBR SHOULD maintain a list of
the peers on the backbone that have associated its link-layer address with
the Registered Address. If that Registered Address moves to another 6BBR,
the previous 6BBR SHOULD unicast a gratuitous NA to each such peer, to supply the LLA of the new 6BBR in the TLLAO for the address.
A 6BBR that does not maintain this list MAY multicast a
gratuitous NA message; this NA
will possibly hit all the nodes on the backbone, whether or not
they maintain an NCE for the Registered Address.
In either case, the 6BBR MAY set the Override flag if it is known that the Registered Node cannot attach to the backbone; this will avoid interruptions and save probing flows in the future.
If a correspondent fails to receive the gratuitous NA, it will keep
sending traffic to a 6BBR to which the node was previously registered.
Since the previous 6BBR removed its host route to the Registered Address,
it will look up the address over the backbone, resolve the address
with the LLA of the new 6BBR, and forward the packet to the correct
6BBR. The previous 6BBR SHOULD also issue a redirect message
to update the cache of the correspondent.
Bridging Proxy Operations
A Bridging Proxy provides IPv6 ND proxy functions between the LLN and the
backbone while preserving the forwarding continuity at the link layer.
It acts as a Layer 2 bridge for all types of unicast packets including
link-scoped, and it appears as an IPv6 Host on the backbone.
The Bridging Proxy registers any Binding, including a link-local
address to the 6LBR (if present), and defends it over the backbone in IPv6
ND procedures.
To achieve this, the Bridging Proxy intercepts the IPv6 ND messages
and may reinject them on the other side, respond directly, or drop them.
For instance, an NS(Lookup) from the backbone that matches a Binding can be
responded to directly or turned into a unicast on the LLN side to let the
6LN respond.
As a Bridging Proxy, the 6BBR MUST use the Registering Node's Layer 2
address in the SLLAO of the NS/RS messages and the TLLAO of the NA
messages that it generates to advertise the Registered Addresses.
The Registering Node's Layer 2 address is found in the SLLAO of the
registration NS(EARO) and maintained in the Binding Table.
The MLSN prefix SHOULD NOT be advertised as on-link in RA
messages sent towards the LLN.
If a destination address is seen as on-link, then a 6LN may use NS(Lookup)
messages to resolve that address. In that case, the 6BBR MUST either answer the NS(Lookup) message directly or reinject the message on the
backbone, as either a Layer 2 unicast or a multicast.
If the Registering Node owns the Registered Address, meaning that the Registering Node is the Registered Node, then its mobility does not impact existing NCEs over the backbone.
In a network where proxy registrations are used, meaning that the Registering Node acts on behalf of the Registered Node, if the Registered Node selects a new Registering Node, then the existing NCEs across the backbone pointing at the old Registering Node must be updated.
In that case, the 6BBR SHOULD attempt to fix the existing NCEs across the backbone pointing at other 6BBRs using NA messages as described in .
This method can fail if the multicast message is not received; one or more
correspondent nodes on the backbone might maintain a stale NCE,
and packets to the Registered Address may be lost.
When this condition happens, it is eventually discovered and
resolved using NUD as
defined in .
Creating and Maintaining a Binding
Upon receiving a registration for a new address (i.e., an NS(EARO) with
the R flag set), the 6BBR creates a Binding and operates as a 6LR according
to , interacting with the 6LBR if one is present.
An implementation of a Routing Proxy that creates a Binding MUST also create an associated host route pointing to the Registering Node in the LLN
interface from which the registration was received.
Acting as a 6BBR, the 6LR operation is modified as follows:
Acting as a Bridging Proxy, the 6LR MUST ND proxy over the
backbone for registered link-local addresses.
EDAR and EDAC messages SHOULD carry an SLLAO and a TLLAO, respectively.
An EDAC message with a status code of 9 ("6LBR Registry Saturated") is
assimilated as a status code of 0 ("Success") if a following DAD process protects the
address against duplication.
This specification enables nodes on a Backbone Link to coexist along
with nodes implementing IPv6 ND as well as other
non-normative specifications such as .
It is possible that not all IPv6 addresses on the backbone are registered
and known to the 6LBR, and an EDAR/EDAC exchange with the 6LBR might
succeed even for a duplicate address.
Consequently, the 6BBR still
needs to perform IPv6 ND DAD over the backbone after an EDAC with a
status code of 0 ("Success") or 9 ("6LBR Registry Saturated").
For the DAD operation, the Binding is placed in Tentative state for a
duration of TENTATIVE_DURATION (),
and an NS(DAD) message is sent as a multicast
message over the backbone to the SNMA associated with the Registered Address
.
The EARO from the registration MUST be placed unchanged in the NS(DAD)
message.
If a registration is received for an existing Binding with a non-null
Registration Lifetime and the registration is fresher (same ROVR, fresher TID), then the Binding is updated with the new Registration Lifetime,
TID, and possibly Registering Node. In Tentative state
(see ), the current DAD operation continues unaltered.
In other states (see Sections and ),
the Binding is placed in Reachable state for the Registration Lifetime, and
the 6BBR returns an NA(EARO) to the Registering Node with a status code of 0
("Success").
Upon a registration that is identical (same ROVR, TID, and Registering
Node), the 6BBR does not alter its current state. In Reachable state, it returns an NA(EARO) back to the Registering Node with a status code of 0 ("Success").
A registration that is not as fresh (same ROVR, older TID) is ignored.
If a registration is received for an existing Binding and a Registration
Lifetime of 0, then the Binding is removed, and the 6BBR returns an
NA(EARO) back to the Registering Node with a status code of 0 ("Success").
An implementation of a Routing Proxy that removes a Binding MUST remove the
associated host route pointing on the Registering Node.
The old 6BBR removes its Binding Table entry and notifies the Registering Node with a status code of 3 ("Moved") if a new 6BBR claims a fresher registration (same ROVR, fresher TID) for the same address.
The old 6BBR MAY preserve a temporary state in order to forward packets in
flight.
The state may be, for instance, an NCE that was formed when an NA message was received. It may also be a Binding Table entry in Stale state, pointing at the new 6BBR on the backbone or any other abstract cache entry that can be used to resolve the link-layer address of the new 6BBR.
The old 6BBR SHOULD also use REDIRECT messages pointing at the new 6BBR to update the correspondents of the Registered Address, as specified in .
Operations on a Binding in Tentative StateThe Tentative state covers a DAD period over the backbone during which
an address being registered is checked for duplication using the procedures
defined in .
For a Binding in Tentative state:
The Binding MUST be removed if an NA message is received over the
backbone for the Registered Address with no EARO or with an EARO that indicates an existing registration owned by a different Registering Node (different ROVR). In that case, an NA is
sent back to the Registering Node with a status code of 1
("Duplicate Address") to indicate that the Binding has been rejected. This behavior might be overridden by policy, in particular
if the registration is trusted, e.g., based on the validation of the
ROVR field (see ).
The Binding MUST be removed if an NS(DAD) message is received over the
backbone for the Registered Address with no EARO or with an EARO that has a different ROVR that indicates a tentative registration by a different Registering Node. In that case, an NA is
sent back to the Registering Node with a status code of 1
("Duplicate Address"). This behavior might be overridden by policy, in particular
if the registration is trusted, e.g., based on the validation of the
ROVR field (see ).
The Binding MUST be removed if an NA or an NS(DAD) message is received over the backbone for the Registered Address and contains an EARO that indicates a fresher registration for the same Registering Node (same ROVR). In that case, an NA MUST be sent back to the Registering Node with a status code of 3 ("Moved").
The Binding MUST be kept unchanged if an NA or an NS(DAD) message is received over the backbone for the Registered Address and contains an EARO that indicates an older registration for the same Registering Node (same ROVR). The message is answered with an NA that carries an EARO with a status code of 3 ("Moved") and the Override flag not set. This behavior might be overridden by policy, in particular if the registration is not trusted.
Other NS(DAD) and NA messages from the backbone are ignored.
NS(Lookup) and NS(NUD) messages SHOULD be optimistically answered with
an NA message containing an EARO with a status code of 0
("Success") and the Override
flag not set (see ).
If optimistic DAD is disabled, then they SHOULD be queued to be answered
when the Binding goes to Reachable state.
When the TENTATIVE_DURATION () timer elapses,
the Binding is placed in
Reachable state for the Registration Lifetime, and the 6BBR returns
an NA(EARO) to the Registering Node with a status code of 0 ("Success").
The 6BBR also attempts to take over any existing Binding from other
6BBRs and to update existing NCEs in backbone nodes. This is done by
sending an NA message with an EARO and the Override flag not set over the backbone
(see Sections and ).
Operations on a Binding in Reachable State
The Reachable state covers an active registration after a successful DAD
process.
If the Registration Lifetime is of a long duration,
an implementation might be configured to reassess the availability of the
Registering Node at a lower period, using a NUD procedure as specified in
. If the NUD procedure fails, the Binding SHOULD be
placed in Stale state immediately.
For a Binding in Reachable state:
The Binding MUST be removed if an NA or an NS(DAD) message is received
over the backbone for the Registered Address and contains an EARO that
indicates a fresher registration for the same
Registered Node (i.e., same ROVR but fresher TID).
A status code of 4 ("Removed") is returned in an asynchronous NA(EARO) to the
Registering Node.
Based on configuration, an implementation may delay this operation by a
timer with a short setting, e.g., a few seconds to a minute, in order
to allow for a parallel registration to reach this node, in which case
the NA might be ignored.
NS(DAD) and NA messages containing an EARO that indicates a
registration for the same Registered Node that is not as fresh as this
Binding MUST be answered with an NA message containing an EARO with a
status code of 3 ("Moved").
An NS(DAD) with no EARO or with an EARO that indicates a duplicate
registration (i.e., different ROVR) MUST be answered with an NA message
containing an EARO with a status code of 1 ("Duplicate Address") and the Override flag
not set, unless the received message is an NA that carries an
EARO with a status code of 1 ("Duplicate Address"), in which case the node refrains from answering.
Other NS(DAD) and NA messages from the backbone are ignored.
NS(Lookup) and NS(NUD) messages SHOULD be answered with
an NA message containing an EARO with a status code of 0
("Success") and the Override
flag not set. The 6BBR MAY check whether
the Registering Node is still available using a NUD procedure over the
LLN prior to answering;
this behavior depends on the use case and is subject to configuration.
When the Registration Lifetime timer elapses, the Binding is placed in
Stale state for a duration of STALE_DURATION ().
Operations on a Binding in Stale State
The Stale state enables tracking of the backbone peers that have a
NCE pointing to this 6BBR in case the Registered Address shows up later.
If the Registered Address is claimed by another 6LN on the backbone, with an
NS(DAD) or an NA, the 6BBR does not defend the address.
For a Binding in Stale state:
The Binding MUST be removed if an NA or an NS(DAD) message is received
over the backbone for the Registered Address with no EARO or with
an EARO that indicates either a fresher registration for the same
Registered Node or a duplicate registration.
A status code of 4 ("Removed") MAY be returned in an asynchronous NA(EARO) to
the Registering Node.
NS(DAD) and NA messages containing an EARO that indicates a
registration for the same Registered Node that is not as fresh as this
MUST be answered with an NA message containing an EARO with a
status code of 3 ("Moved").
If the 6BBR receives an NS(Lookup) or an NS(NUD) message for the
Registered Address, the 6BBR MUST attempt a NUD procedure as specified
in to the Registering Node, targeting
the Registered Address, prior to answering. If the NUD procedure
succeeds, the operation in Reachable state applies. If the NUD fails,
the 6BBR refrains from answering.
Other NS(DAD) and NA messages from the backbone are ignored.
When the STALE_DURATION () timer elapses, the
Binding MUST be removed.
Registering Node Considerations
A Registering Node MUST implement in order to
interact with a 6BBR (which acts as a Routing Registrar). Following
, the Registering Node signals that it requires IPv6
ND proxy services from a 6BBR by registering the corresponding IPv6 address
using an NS(EARO) message with the R flag set.
The Registering Node may be the 6LN owning the IPv6 address or a 6LBR that
performs the registration on its behalf in a route-over mesh.
A 6LN MUST register all of its IPv6 addresses to its 6LR,
which is the 6BBR when they are connected at Layer 2. Failure to register an
address may result in the address being unreachable by other parties. This
would happen, for instance, if the 6BBR propagates the NS(Lookup) from the backbone only to the LLN nodes that do not register their addresses.
The Registering Node MUST refrain from using multicast NS(Lookup) when the
destination is not known as on-link, e.g., if the prefix is advertised
in a PIO with the L flag not set. In that case, the Registering
Node sends its packets directly to its 6LR.
The Registering Node SHOULD also follow BCP 202 in order to
limit the use of multicast RAs. It SHOULD also implement
"Simple Procedures for Detecting Network Attachment
in IPv6" (DNA procedures) to detect movements and
support
"Packet-Loss Resiliency for Router Solicitations" in order to
improve reliability for the unicast RS messages.
Security Considerations
The procedures in this document modify the mechanisms used for IPv6 ND
and DAD and should not affect other aspects of IPv6 or
higher-level-protocol operation. As such, the main classes of attacks
that are in play are those that work to block Neighbor Discovery or to
forcibly claim an address that another node is attempting to use. In the
absence of cryptographic protection at higher layers, the latter class of
attacks can have significant consequences, with the attacker being able
to read all the "stolen" traffic that was directed to the target of the
attack.
This specification applies to LLNs and a backbone in which the individual links are protected against rogue access on the LLN by authenticating a node that attaches to the network and encrypting the transmissions at the link layer and on the backbone side, using the physical security and access control measures that are typically applied there; thus, packets may neither be forged nor overheard.
In particular, the LLN link layer is required to provide secure unicast to/from the
Backbone Router and secure broadcast from the routers
in a way that prevents tampering with or replaying the ND messages.
For the IPv6 ND operation over the backbone, and unless the classical ND
is disabled (e.g., by configuration), the classical ND messages are
interpreted as emitted by the address owner and have precedence over the
6BBR that is only a proxy.
As a result, the security threats that are
detailed in fully apply to this
specification as well. In short:
Any node that can send a packet on the backbone can take over any address,
including addresses of LLN nodes, by
claiming it with an NA message and the Override bit set. This means that the
real owner will stop receiving its packets.
Any node that can send a packet on the backbone can forge traffic and
pretend it is issued from an address that it does not own, even if it did
not claim the address using ND.
Any node that can send a packet on the backbone can present itself as a
preferred router to intercept all traffic outgoing on the subnet. It may even
expose a prefix on the subnet as "not-on-link" and intercept all the traffic
within the subnet.
If the rogue can receive a packet from the backbone, it can also snoop
all the intercepted traffic, by stealing an address or the role of a
router.
This means that any rogue access to the backbone must be prevented
at all times, and nodes that are attached to the backbone must be fully
trusted / never compromised.
Using address registration as the sole ND mechanism on a link and coupling
it with guarantees the ownership of a Registered Address within that link.
The protection is based on a proof of ownership encoded in the ROVR field, and it protects against address theft and impersonation by a 6LN, because the 6LR can challenge the Registered Node for a proof of ownership.
The protection extends to the full LLN in the case of an LLN link, but it does not extend over the backbone since the 6BBR cannot provide the proof of ownership
when it defends the address.
A possible attack over the backbone can be done by sending an NS with
an EARO and expecting the NA(EARO) back to contain the TID and ROVR
fields of the existing state. With that information, the attacker can
easily increase the TID and take over the Binding.
If the classical ND is disabled on the backbone and the use of and a 6LBR are mandated, the network will benefit from
the following new advantages:
Zero-trust security for ND flows within the whole subnet:
the increased security that provides on the LLN will also apply to the backbone; it becomes impossible for an attached node to claim an address that belongs to another node using ND, and the network can filter packets that are not originated by the owner of the source address (Source Address Validation Improvement (SAVI)), as long as the routers are known and trusted.
Remote ND DoS attack avoidance:
the complete list of addresses in the network will be known to the 6LBR and available to the default router; with that information, the router does not need to send a multicast NS(Lookup) in case of a Neighbor Cache miss for an incoming packet, which is a source of remote DoS attack against the network.
Less IPv6 ND-related multicast on the backbone:
DAD and NS(Lookup) become unicast queries to the 6LBR.
Better DAD operation on wireless:
DAD has been found to fail to detect duplications on large Wi-Fi infrastructures due to the unreliable broadcast operation on wireless; using a 6LBR enables a unicast lookup.
Less Layer 2 churn on the backbone:
Using the Routing Proxy approach, the link-layer address of the LLN devices and their mobility are not visible in the backbone; only the link-Layer addresses of the 6BBR and backbone nodes are visible at Layer 2 on the backbone. This is mandatory for LLNs that cannot be bridged on the backbone and useful in any case to scale down, stabilize the forwarding tables at Layer 2, and avoid the gratuitous frames that are typically broadcasted to fix the transparent bridging tables when a wireless node roams from an AP to the next.
This specification introduces a 6BBR that is a router on the path of the LLN
traffic and a 6LBR that is used for the lookup. They could be interesting
targets for an attacker. A compromised 6BBR can accept a registration but
block the traffic or refrain from proxying. A compromised 6LBR may
unduly accept the transfer of ownership of an address or block a newcomer by
faking that its address is a duplicate. But those attacks are possible
in a classical network from a compromised default router and a DHCP
server, respectively, and can be prevented using the same methods.
A possible attack over the LLN can still be done by compromising a 6LR.
A compromised 6LR may modify the ROVR of EDAR messages in flight and transfer
the ownership of the Registered Address to itself or a tier. It may also claim
that a ROVR was validated when it really wasn't and reattribute an address
to itself or to an attached 6LN. This means that 6LRs, as well as 6LBRs and
6BBRS, must still be fully trusted / never compromised.
This specification mandates checking on the 6LBR on the backbone before doing
the classical DAD, in case the address already exists. This may delay the DAD
operation and should be protected by a short timer, in the order of 100 ms or
less, which will only represent a small extra delay versus the 1 s wait of the
DAD operation.
Protocol Constants
This specification uses the following constants:
TENTATIVE_DURATION:
800 milliseconds
In LLNs with long-lived addresses such as Low-Power WAN (LPWANs), STALE_DURATION
SHOULD be configured with a relatively long value to cover an interval when the address may be reused and before it is safe to expect that the address was definitively released. A good default value is 24 hours.
In LLNs where addresses are renewed rapidly, e.g., for privacy reasons,
STALE_DURATION SHOULD be configured with a relatively shorter value -- 5 minutes by default.
IANA Considerations This document has no IANA actions.Normative ReferencesKey words for use in RFCs to Indicate Requirement LevelsIn many standards track documents several words are used to signify the requirements in the specification. These words are often capitalized. This document defines these words as they should be interpreted in IETF documents. This document specifies an Internet Best Current Practices for the Internet Community, and requests discussion and suggestions for improvements.IP Version 6 Addressing ArchitectureThis specification defines the addressing architecture of the IP Version 6 (IPv6) protocol. The document includes the IPv6 addressing model, text representations of IPv6 addresses, definition of IPv6 unicast addresses, anycast addresses, and multicast addresses, and an IPv6 node's required addresses.This document obsoletes RFC 3513, "IP Version 6 Addressing Architecture". [STANDARDS-TRACK]Optimistic Duplicate Address Detection (DAD) for IPv6Optimistic Duplicate Address Detection is an interoperable modification of the existing IPv6 Neighbor Discovery (RFC 2461) and Stateless Address Autoconfiguration (RFC 2462) processes. The intention is to minimize address configuration delays in the successful case, to reduce disruption as far as possible in the failure case, and to remain interoperable with unmodified hosts and routers. [STANDARDS-TRACK]Neighbor Discovery for IP version 6 (IPv6)This document specifies the Neighbor Discovery protocol for IP Version 6. IPv6 nodes on the same link use Neighbor Discovery to discover each other's presence, to determine each other's link-layer addresses, to find routers, and to maintain reachability information about the paths to active neighbors. [STANDARDS-TRACK]IPv6 Stateless Address AutoconfigurationThis document specifies the steps a host takes in deciding how to autoconfigure its interfaces in IP version 6. The autoconfiguration process includes generating a link-local address, generating global addresses via stateless address autoconfiguration, and the Duplicate Address Detection procedure to verify the uniqueness of the addresses on a link. [STANDARDS-TRACK]Simple Procedures for Detecting Network Attachment in IPv6Detecting Network Attachment allows hosts to assess if its existing addressing or routing configuration is valid for a newly connected network. This document provides simple procedures for Detecting Network Attachment in IPv6 hosts, and procedures for routers to support such services. [STANDARDS-TRACK]Neighbor Discovery Optimization for IPv6 over Low-Power Wireless Personal Area Networks (6LoWPANs)The IETF work in IPv6 over Low-power Wireless Personal Area Network (6LoWPAN) defines 6LoWPANs such as IEEE 802.15.4. This and other similar link technologies have limited or no usage of multicast signaling due to energy conservation. In addition, the wireless network may not strictly follow the traditional concept of IP subnets and IP links. IPv6 Neighbor Discovery was not designed for non- transitive wireless links, as its reliance on the traditional IPv6 link concept and its heavy use of multicast make it inefficient and sometimes impractical in a low-power and lossy network. This document describes simple optimizations to IPv6 Neighbor Discovery, its addressing mechanisms, and duplicate address detection for Low- power Wireless Personal Area Networks and similar networks. The document thus updates RFC 4944 to specify the use of the optimizations defined here. [STANDARDS-TRACK]Neighbor Unreachability Detection Is Too ImpatientIPv6 Neighbor Discovery includes Neighbor Unreachability Detection. That function is very useful when a host has an alternative neighbor -- for instance, when there are multiple default routers -- since it allows the host to switch to the alternative neighbor in a short time. By default, this time is 3 seconds after the node starts probing. However, if there are no alternative neighbors, this timeout behavior is far too impatient. This document specifies relaxed rules for Neighbor Discovery retransmissions that allow an implementation to choose different timeout behavior based on whether or not there are alternative neighbors. This document updates RFC 4861.Packet-Loss Resiliency for Router SolicitationsWhen an interface on a host is initialized, the host transmits Router Solicitations in order to minimize the amount of time it needs to wait until the next unsolicited multicast Router Advertisement is received. In certain scenarios, these Router Solicitations transmitted by the host might be lost. This document specifies a mechanism for hosts to cope with the loss of the initial Router Solicitations.Reducing Energy Consumption of Router AdvertisementsFrequent Router Advertisement messages can severely impact host power consumption. This document recommends operational practices to avoid such impact.Ambiguity of Uppercase vs Lowercase in RFC 2119 Key WordsRFC 2119 specifies common key words that may be used in protocol specifications. This document aims to reduce the ambiguity by clarifying that only UPPERCASE usage of the key words have the defined special meanings.Internet Protocol, Version 6 (IPv6) SpecificationThis document specifies version 6 of the Internet Protocol (IPv6). It obsoletes RFC 2460.Path MTU Discovery for IP version 6This document describes Path MTU Discovery (PMTUD) for IP version 6. It is largely derived from RFC 1191, which describes Path MTU Discovery for IP version 4. It obsoletes RFC 1981.Registration Extensions for IPv6 over Low-Power Wireless Personal Area Network (6LoWPAN) Neighbor DiscoveryThis specification updates RFC 6775 -- the Low-Power Wireless Personal Area Network (6LoWPAN) Neighbor Discovery specification -- to clarify the role of the protocol as a registration technique and simplify the registration operation in 6LoWPAN routers, as well as to provide enhancements to the registration capabilities and mobility detection for different network topologies, including the Routing Registrars performing routing for host routes and/or proxy Neighbor Discovery in a low-power network.Informative ReferencesAn Architecture for IPv6 over the TSCH mode of IEEE 802.15.4Cisco Systems, Inc This document describes a network architecture that provides low-
latency, low-jitter and high-reliability packet delivery. It
combines a high-speed powered backbone and subnetworks using IEEE
802.15.4 time-slotted channel hopping (TSCH) to meet the requirements
of LowPower wireless deterministic applications.
Work in ProgressPossible approaches to make DAD more robust and/or efficient This outlines possible approaches to solve the issues around IPv6
Duplicate Address Detection robustness and/or efficiency which are
specified in the "DAD issues" dradft.
Work in ProgressA survey of issues related to IPv6 Duplicate Address Detection This document enumerates the practical issues observed with respect
to Duplicate Address Detection.
Work in ProgressIEEE Standard for Information technology--Telecommunications and information exchange between systems Local and metropolitan area networks--Specific requirements - Part 11: Wireless LAN Medium Access Control (MAC) and Physical Layer (PHY) SpecificationsIEEEIEEE Standard for Information technology--Local and metropolitan area networks--Specific requirements--Part 15.1a: Wireless Medium Access Control (MAC) and Physical Layer (PHY) specifications for Wireless Personal Area Networks (WPAN)IEEEMethods for communicating devices in a personal area network (PAN) are covered in this standard.IEEE Standard for Local and metropolitan area networks--Part 15.4: Low-Rate Wireless Personal Area Networks (LR-WPANs)IEEEIEEE Standard for Local and Metropolitan Area Networks--Bridges and Bridged NetworksIEEEMulticast Considerations over IEEE 802 Wireless MediaBlue Meadow NetworksFuturewei Technologies Inc.Hewlett Packard EnterpriseGoogleSIGFOX Well-known issues with multicast have prevented the deployment of
multicast in 802.11 (wifi) and other local-area wireless
environments. This document describes the problems of known
limitations with wireless (primarily 802.11) Layer-2 multicast. Also
described are certain multicast enhancement features that have been
specified by the IETF, and by IEEE 802, for wireless media, as well
as some operational choices that can be taken to improve the
performance of the network. Finally, some recommendations are
provided about the usage and combination of these features and
operational choices.
Work in ProgressA Border Gateway Protocol 4 (BGP-4)This document discusses the Border Gateway Protocol (BGP), which is an inter-Autonomous System routing protocol.The primary function of a BGP speaking system is to exchange network reachability information with other BGP systems. This network reachability information includes information on the list of Autonomous Systems (ASes) that reachability information traverses. This information is sufficient for constructing a graph of AS connectivity for this reachability from which routing loops may be pruned, and, at the AS level, some policy decisions may be enforced.BGP-4 provides a set of mechanisms for supporting Classless Inter-Domain Routing (CIDR). These mechanisms include support for advertising a set of destinations as an IP prefix, and eliminating the concept of network "class" within BGP. BGP-4 also introduces mechanisms that allow aggregation of routes, including aggregation of AS paths.This document obsoletes RFC 1771. [STANDARDS-TRACK]Neighbor Discovery Proxies (ND Proxy)Bridging multiple links into a single entity has several operational advantages. A single subnet prefix is sufficient to support multiple physical links. There is no need to allocate subnet numbers to the different networks, simplifying management. Bridging some types of media requires network-layer support, however. This document describes these cases and specifies the IP-layer support that enables bridging under these circumstances. This memo defines an Experimental Protocol for the Internet community.Multi-Link Subnet IssuesThere have been several proposals around the notion that a subnet may span multiple links connected by routers. This memo documents the issues and potential problems that have been raised with such an approach. This memo provides information for the Internet community.OSPF for IPv6This document describes the modifications to OSPF to support version 6 of the Internet Protocol (IPv6). The fundamental mechanisms of OSPF (flooding, Designated Router (DR) election, area support, Short Path First (SPF) calculations, etc.) remain unchanged. However, some changes have been necessary, either due to changes in protocol semantics between IPv4 and IPv6, or simply to handle the increased address size of IPv6. These modifications will necessitate incrementing the protocol version from version 2 to version 3. OSPF for IPv6 is also referred to as OSPF version 3 (OSPFv3).Changes between OSPF for IPv4, OSPF Version 2, and OSPF for IPv6 as described herein include the following. Addressing semantics have been removed from OSPF packets and the basic Link State Advertisements (LSAs). New LSAs have been created to carry IPv6 addresses and prefixes. OSPF now runs on a per-link basis rather than on a per-IP-subnet basis. Flooding scope for LSAs has been generalized. Authentication has been removed from the OSPF protocol and instead relies on IPv6's Authentication Header and Encapsulating Security Payload (ESP).Even with larger IPv6 addresses, most packets in OSPF for IPv6 are almost as compact as those in OSPF for IPv4. Most fields and packet- size limitations present in OSPF for IPv4 have been relaxed. In addition, option handling has been made more flexible.All of OSPF for IPv4's optional capabilities, including demand circuit support and Not-So-Stubby Areas (NSSAs), are also supported in OSPF for IPv6. [STANDARDS-TRACK]Control And Provisioning of Wireless Access Points (CAPWAP) Protocol SpecificationThis specification defines the Control And Provisioning of Wireless Access Points (CAPWAP) Protocol, meeting the objectives defined by the CAPWAP Working Group in RFC 4564. The CAPWAP protocol is designed to be flexible, allowing it to be used for a variety of wireless technologies. This document describes the base CAPWAP protocol, while separate binding extensions will enable its use with additional wireless technologies. [STANDARDS-TRACK]Mobility Support in IPv6This document specifies Mobile IPv6, a protocol that allows nodes to remain reachable while moving around in the IPv6 Internet. Each mobile node is always identified by its home address, regardless of its current point of attachment to the Internet. While situated away from its home, a mobile node is also associated with a care-of address, which provides information about the mobile node's current location. IPv6 packets addressed to a mobile node's home address are transparently routed to its care-of address. The protocol enables IPv6 nodes to cache the binding of a mobile node's home address with its care-of address, and to then send any packets destined for the mobile node directly to it at this care-of address. To support this operation, Mobile IPv6 defines a new IPv6 protocol and a new destination option. All IPv6 nodes, whether mobile or stationary, can communicate with mobile nodes. This document obsoletes RFC 3775. [STANDARDS-TRACK]RPL: IPv6 Routing Protocol for Low-Power and Lossy NetworksLow-Power and Lossy Networks (LLNs) are a class of network in which both the routers and their interconnect are constrained. LLN routers typically operate with constraints on processing power, memory, and energy (battery power). Their interconnects are characterized by high loss rates, low data rates, and instability. LLNs are comprised of anything from a few dozen to thousands of routers. Supported traffic flows include point-to-point (between devices inside the LLN), point-to-multipoint (from a central control point to a subset of devices inside the LLN), and multipoint-to-point (from devices inside the LLN towards a central control point). This document specifies the IPv6 Routing Protocol for Low-Power and Lossy Networks (RPL), which provides a mechanism whereby multipoint-to-point traffic from devices inside the LLN towards a central control point as well as point-to-multipoint traffic from the central control point to the devices inside the LLN are supported. Support for point-to-point traffic is also available. [STANDARDS-TRACK]Problem Statement and Requirements for IPv6 over Low-Power Wireless Personal Area Network (6LoWPAN) RoutingIPv6 over Low-Power Wireless Personal Area Networks (6LoWPANs) are formed by devices that are compatible with the IEEE 802.15.4 standard. However, neither the IEEE 802.15.4 standard nor the 6LoWPAN format specification defines how mesh topologies could be obtained and maintained. Thus, it should be considered how 6LoWPAN formation and multi-hop routing could be supported.This document provides the problem statement and design space for 6LoWPAN routing. It defines the routing requirements for 6LoWPANs, considering the low-power and other particular characteristics of the devices and links. The purpose of this document is not to recommend specific solutions but to provide general, layer-agnostic guidelines about the design of 6LoWPAN routing that can lead to further analysis and protocol design. This document is intended as input to groups working on routing protocols relevant to 6LoWPANs, such as the IETF ROLL WG. This document is not an Internet Standards Track specification; it is published for informational purposes.The Locator/ID Separation Protocol (LISP)This document describes a network-layer-based protocol that enables separation of IP addresses into two new numbering spaces: Endpoint Identifiers (EIDs) and Routing Locators (RLOCs). No changes are required to either host protocol stacks or to the "core" of the Internet infrastructure. The Locator/ID Separation Protocol (LISP) can be incrementally deployed, without a "flag day", and offers Traffic Engineering, multihoming, and mobility benefits to early adopters, even when there are relatively few LISP-capable sites.Design and development of LISP was largely motivated by the problem statement produced by the October 2006 IAB Routing and Addressing Workshop. This document defines an Experimental Protocol for the Internet community.BGP MPLS-Based Ethernet VPNThis document describes procedures for BGP MPLS-based Ethernet VPNs (EVPN). The procedures described here meet the requirements specified in RFC 7209 -- "Requirements for Ethernet VPN (EVPN)".Unique IPv6 Prefix per HostThis document outlines an approach utilizing existing IPv6 protocols to allow hosts to be assigned a unique IPv6 prefix (instead of a unique IPv6 address from a shared IPv6 prefix). Benefits of using a unique IPv6 prefix over a unique service-provider IPv6 address include improved host isolation and enhanced subscriber management on shared network segments.Address-Protected Neighbor Discovery for Low-Power and Lossy NetworksRIFT: Routing in Fat TreesJuniperComcastCisco Systems, IncIndividualYandex This document defines a specialized, dynamic routing protocol for
Clos and fat-tree network topologies optimized towards minimization
of configuration and operational complexity. The protocol
o deals with no configuration, fully automated construction of fat-
tree topologies based on detection of links,
o minimizes the amount of routing state held at each level,
o automatically prunes and load balances topology flooding exchanges
over a sufficient subset of links,
o supports automatic disaggregation of prefixes on link and node
failures to prevent black-holing and suboptimal routing,
o allows traffic steering and re-routing policies,
o allows loop-free non-ECMP forwarding,
o automatically re-balances traffic towards the spines based on
bandwidth available and finally
o provides mechanisms to synchronize a limited key-value data-store
that can be used after protocol convergence to e.g. bootstrap
higher levels of functionality on nodes.
Work in ProgressRouting for RPL LeavesCisco Systems, IncSandelman Software Works This specification updates RFC6550, RFC6775, and RFC8505, to provide
routing services to RPL Unaware Leaves that implement 6LoWPAN ND and
the extensions therein.
Work in ProgressIPv6 Neighbor Discovery Optional RS/RA Refresh IPv6 Neighbor Discovery relies on periodic multicast Router
Advertisement messages to update timer values and to distribute new
information (such as new prefixes) to hosts. On some links the use
of periodic multicast messages to all host becomes expensive, and in
some cases it results in hosts waking up frequently. Many
implementations of RFC 4861 also use multicast for solicited Router
Advertisement messages, even though that behavior is optional.
This specification provides an optional mechanism for hosts and
routers where instead of periodic multicast Router Advertisements the
hosts are instructed (by the routers) to use Router Solicitations to
request refreshed Router Advertisements. This mechanism is enabled
by configuring the router to include a new option in the Router
Advertisement in order to allow the network administrator to choose
host behavior based on whether periodic multicast are more efficient
on their link or not. The routers can also tell whether the hosts
are capable of the new behavior through a new flag in the Router
Solicitations.
Work in ProgressA SAVI Solution for WLANTsinghua UniversityTsinghua UniversityTsinghua UniversityNew H3C Technologies Co. Ltd This document describes a source address validation solution for WLAN
enabling 802.11i or other security mechanisms. This mechanism snoops
NDP and DHCP packets to bind IP address to MAC address, and relies on
the security of MAC address guaranteed by 802.11i or other mechanisms
to filter IP spoofing packets. It can work in the special situations
described in the charter of SAVI(Source Address Validation
Improvements) workgroup, such as multiple MAC addresses on one
interface. This document describes three different deployment
scenarios, with solutions for migration of binding entries when hosts
move from one access point to another.
Work in ProgressIPv6 Neighbor Discovery Unicast LookupCisco Systems, IncCisco Systems, Inc This document updates RFC 8505 in order to enable unicast address
lookup from a 6LoWPAN Border Router acting as an Address Registrar.
Work in ProgressPossible Future Extensions
With the current specification, the 6LBR is not leveraged to avoid
multicast NS(Lookup) on the backbone. This could be done by adding
a lookup procedure in the EDAR/EDAC exchange.
By default, the specification does not have a fine-grained trust model: all nodes that can authenticate to the LLN link layer or attach to the backbone are equally trusted. It would be desirable to provide a stronger authorization model, e.g., whereby
nodes that associate their address with a proof of ownership
should be trusted more than nodes that
do not. Such a trust model and related signaling could be added in the
future to override the default operation and favor trusted nodes.
As an alternate to the ND Proxy operation, the registration may be redistributed as a
host route in a routing protocol that would operate over the backbone; this is already
happening in IoT networks and Data Center Routing
and could be extended to other protocols, e.g., BGP and OSPFv3 .
The registration may also be advertised in an overlay protocol such as Mobile IPv6 (MIPv6) ,
the Locator/ID Separation Protocol (LISP) , or Ethernet VPN (EVPN) .
Applicability and Requirements Served
This document specifies ND proxy functions that can be used to
federate an IPv6 Backbone Link and multiple IPv6 LLNs into a
single MLSN. The ND proxy functions enable IPv6 ND
services for DAD and address lookup
that do not require broadcasts over the LLNs.
The term LLN is used to cover multiple types of WLANs and WPANs,
including (Low-Power) Wi-Fi, BLUETOOTH(R) Low Energy,
IEEE Std 802.11ah and IEEE Std 802.15.4 wireless meshes, and the
types of networks listed in "Requirements Related to Various Low-Power Link Types"
(see ).
Each LLN in the subnet is attached to a 6BBR.
The Backbone Routers interconnect the LLNs and advertise the addresses
of the 6LNs over the Backbone Link using ND proxy operations.
This specification updates IPv6 ND over the backbone to
distinguish address movement from duplication and eliminate Stale
state in the backbone routers and backbone nodes once a 6LN has
roamed. This way, mobile nodes may roam rapidly from
one 6BBR to the next, and requirements are met per "Requirements Related to Mobility" (see
).
A 6LN can register its IPv6 addresses and thereby obtain ND proxy
services over the backbone, meeting the requirements
expressed in "Requirements Related to Proxy Operations" (see .
The negative impact of the IPv6 ND-related broadcasts can be limited to one of the federated links, enabling the number of 6LNs to grow. The Routing Proxy operation avoids the need to expose the link-layer addresses of the 6LNs onto the backbone, keeping the Layer 2 topology simple and stable. This meets the requirements in "Requirements Related to Scalability" (see ), as long as the 6BBRs are dimensioned for the number of registrations that each needs to support.
In the case of a Wi-Fi access link, a 6BBR may be collocated
with the AP, a Fabric Edge (FE), or a Control and Provisioning of Wireless Access Points (CAPWAP)
Wireless LAN Controller (WLC).
In those cases, the wireless client (STA) is the 6LN
that makes use of to register its IPv6
address(es) to the 6BBR acting as the Routing Registrar. The 6LBR can be
centralized and either connected to the Backbone Link or reachable
over IP.
The 6BBR ND proxy operations eliminate the need for wireless nodes
to respond synchronously when a lookup is performed for their IPv6
addresses. This provides the function of a Sleep Proxy for ND
.
For the Time-Slotted Channel Hopping (TSCH) mode of
, the
6TiSCH architecture
describes how a 6LoWPAN ND host could connect to the Internet via a
RPL mesh network, but doing so requires extensions to the 6LOWPAN ND
protocol to support mobility and reachability in a secure and
manageable environment. The extensions detailed in this document
also work for the 6TiSCH architecture, serving the requirements listed
in "Requirements Related to Routing Protocols" (see ).
The registration mechanism may be seen as a more reliable alternate to
snooping . Note that
registration and snooping are not mutually exclusive. Snooping may be used in
conjunction with the registration for nodes that do not register their IPv6
addresses.
The 6BBR assumes that if a node registers at least one IPv6 address to it,
then the node registers all of its addresses to the 6BBR.
With this assumption, the 6BBR can possibly cancel all undesirable multicast
NS messages that would otherwise have been delivered to that node.
Scalability of the MLSN requires
avoidance of multicast/broadcast operations as much as possible even on
the backbone .
Although hosts can connect to the backbone using IPv6 ND operations,
multicast RAs can be saved by using
, which also requires the
support of .
AcknowledgmentsMany thanks to , , and for their various contributions.
Also, many thanks to and for their help, review, and support in preparation for the IESG cycle and to , , , , , , and especially and for their useful contributions through the IETF Last Call and IESG process.
Authors' AddressesCisco Systems, Inc.Building D45 Allee des Ormes - BP1200MOUGINS - Sophia Antipolis06254France+33 497 23 26 34pthubert@cisco.comBlue Meadow NetworkingSaratogaCA95070United States of Americacharliep@computer.orgCisco Systems, Inc.Building D45 Allee des Ormes - BP1200MOUGINS - Sophia Antipolis06254France+33 497 23 26 20elevyabe@cisco.com