Rfc6959
TitleSource Address Validation Improvement (SAVI) Threat Scope
AuthorD. McPherson, F. Baker, J. Halpern
DateMay 2013
Format:TXT, HTML
Status:INFORMATIONAL






Internet Engineering Task Force (IETF)                      D. McPherson
Request for Comments: 6959                                VeriSign, Inc.
Category: Informational                                         F. Baker
ISSN: 2070-1721                                            Cisco Systems
                                                              J. Halpern
                                                                Ericsson
                                                                May 2013


       Source Address Validation Improvement (SAVI) Threat Scope

Abstract

   The Source Address Validation Improvement (SAVI) effort aims to
   complement ingress filtering with finer-grained, standardized IP
   source address validation.  This document describes threats enabled
   by IP source address spoofing both in the global and finer-grained
   context, describes currently available solutions and challenges, and
   provides a starting point analysis for finer-grained (host
   granularity) anti-spoofing work.

Status of This Memo

   This document is not an Internet Standards Track specification; it is
   published for informational purposes.

   This document is a product of the Internet Engineering Task Force
   (IETF).  It represents the consensus of the IETF community.  It has
   received public review and has been approved for publication by the
   Internet Engineering Steering Group (IESG).  Not all documents
   approved by the IESG are a candidate for any level of Internet
   Standard; see Section 2 of RFC 5741.

   Information about the current status of this document, any errata,
   and how to provide feedback on it may be obtained at
   http://www.rfc-editor.org/info/rfc6959.















RFC 6959                    SAVI Threat Scope                   May 2013


Copyright Notice

   Copyright (c) 2013 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Table of Contents

   1. Overview ........................................................3
   2. Glossary of Terms ...............................................5
   3. Spoof-Based Attack Vectors ......................................6
      3.1. Blind Attacks ..............................................6
           3.1.1. Single-Packet Attacks ...............................6
           3.1.2. Flood-Based DoS .....................................7
           3.1.3. Poisoning Attacks ...................................8
           3.1.4. Spoof-Based Worm/Malware Propagation ................8
           3.1.5. Reflective Attacks ..................................8
           3.1.6. Accounting Subversion ...............................9
           3.1.7. Other Blind Spoofing Attacks ........................9
      3.2. Non-blind Attacks ..........................................9
           3.2.1. Man in the Middle (MITM) ............................9
           3.2.2. Third-Party Recon ..................................10
           3.2.3. Other Non-blind Spoofing Attacks ...................10
   4. Current Anti-spoofing Solutions ................................11
      4.1. Topological Locations for Enforcement .....................13
           4.1.1. Host to Link-Layer Neighbor via Switch .............13
           4.1.2. Upstream Switches ..................................13
           4.1.3. Upstream Routers ...................................14
           4.1.4. ISP Edge PE Router .................................14
           4.1.5. ISP NNI Router to ISP NNI Router ...................15
           4.1.6. Cable Modem Subscriber Access ......................15
           4.1.7. DSL Subscriber Access ..............................15
      4.2. Currently Available Tools .................................16
           4.2.1. BCP 38 .............................................16
           4.2.2. Unicast RPF ........................................16
           4.2.3. Port-Based Address Binding .........................16
           4.2.4. Cryptographic Techniques ...........................17
           4.2.5. Residual Attacks ...................................18




RFC 6959                    SAVI Threat Scope                   May 2013


   5. Topological Challenges Facing SAVI .............................18
      5.1. Address Provisioning Mechanisms ...........................18
      5.2. LAN Devices with Multiple Addresses .......................18
           5.2.1. Routers ............................................18
           5.2.2. NATs ...............................................19
           5.2.3. Multi-instance Hosts ...............................19
           5.2.4. Multi-LAN Hosts ....................................20
           5.2.5. Firewalls ..........................................20
           5.2.6. Mobile IP ..........................................20
           5.2.7. Other Topologies ...................................21
      5.3. IPv6 Considerations .......................................21
   6. Analysis of Host Granularity Anti-spoofing .....................21
   7. Security Considerations ........................................22
      7.1. Privacy Considerations ....................................23
   8. Acknowledgments ................................................24
   9. References .....................................................24
      9.1. Normative References ......................................24
      9.2. Informative References ....................................24

1.  Overview

   The Internet Protocol, specifically IPv4 [RFC0791] and IPv6
   [RFC2460], employs a connectionless hop-by-hop packet forwarding
   paradigm.  A host connected to an IP network that wishes to
   communicate with another host on the network generates an IP packet
   with source and destination IP addressing information, among other
   options.

   At the IP network layer, or Internet layer, there is typically no
   required transactional state when communicating with other hosts on
   the network.  In particular, the network does not track any state
   about the hosts using the network.  This is normally a benefit.
   However, as a consequence of this, hosts generating packets for
   transmission have the opportunity to spoof (forge) the source address
   of packets that they transmit, as the network does not have any way
   to tell that some of the information is false.

   Source address validation is necessary in order to detect and reject
   spoofed IP packets in the network, and contributes to the overall
   security of IP networks.  This document deals with the subset of such
   validation done by the network based on observed traffic and policy.
   Such source address validation techniques enable detection and
   rejection of many spoofed packets, and also implicitly provide some
   assurances that the source address in an IP packet is legitimately
   assigned to the system that generated the packet.






RFC 6959                    SAVI Threat Scope                   May 2013


   Solutions such as those described in BCP 38 [RFC2827] provide
   guidelines for one such technique for network ingress filtering.
   However, if these techniques are not implemented at the ingress point
   of the IP network, then the validity of the source address cannot be
   positively ascertained.  Furthermore, BCP 38 only implies source
   address validation at the Internet layer and is most often
   implemented on IP subnetwork address boundaries.  One of the
   difficulties in encouraging the deployment of BCP 38 is that there is
   relatively little benefit until it is very widely deployed, which is
   not yet the case.

   Hence, in order to try to get better behavior, it is helpful to look
   for an application like that described in BCP 38, but one that can be
   applied locally and give locally beneficial results.  The local
   benefit would provide a reason for the site to deploy, while moving
   the Internet as a whole towards an environment where BCP 38 is widely
   effected.  SAVI is aimed at providing more specific protection
   locally, with the benefit of better local behavior and, in
   conjunction with appropriate logging, better local traceability,
   while also providing better compliance with the cases dealt with by
   BCP 38.

   It should be noted that while BCP 38 directs providers to provide
   protection from spoofed prefixes, it is clearly desirable for
   enterprise operators to provide that protection more locally, and
   with better traceability.  This allows the enterprise to be a better
   Internet participant and to quickly detect and remedy problems when
   they occur.  For example, when an enterprise receives a report of an
   attack originating within that enterprise, the operational staff
   desires to be able to track from the IP address sourcing the attack
   to the particular machine within the enterprise that is the source.
   This is typically simpler and more reliable than other techniques,
   such as trying to find the attack in ongoing outbound traffic.  To do
   this, the enterprise needs usable address assignment and usage
   information (appropriate logging), as well as accurate information
   (SAVI), to determine that no other machine could have been using that
   address.

   Also, there is a possibility that in a LAN environment where multiple
   hosts share a single LAN or IP port on a switch or router, one of
   those hosts may spoof the source addresses of other hosts within the
   local subnet.  Understanding these threats and the relevant
   topologies in which they're introduced is critical when assessing the
   threats that exist with source address spoofing.

   This document provides additional details regarding spoof-based
   threat vectors and discusses implications of various network
   topologies.



RFC 6959                    SAVI Threat Scope                   May 2013


2.  Glossary of Terms

   The following acronyms and terms are used throughout this memo.

   Binding Anchor:  The relationship used by a device performing source
      address enforcement to perform the validation and enforcement.
      Examples in different situations include Layer 2 addresses or
      physical ports.

   BGP:  The Border Gateway Protocol, used to manage routing policy
      between large networks.

   CPE Router:  Customer Premises Equipment router.  The router on the
      customer premises, whether owned by the customer or the provider.
      Also called the Customer Edge, or CE, router.

   IP Address:  An Internet Protocol address, whether IPv4 or IPv6.

   ISP:  Internet Service Provider.  Any person or company that delivers
      Internet service to another.

   MAC Address:  An Ethernet address or comparable IEEE 802 series
      address.

   NNI Router:  Network-to-Network Interface router.  This router
      interface faces a similar system operated by another ISP or other
      large network.

   PE Router:  Provider Edge router.  This router faces a customer of an
      ISP.

   Spoofing:  The act of sending a datagram header whose contents at the
      link layer or network layer do not match the network policies and
      activities on address assignment or claiming.  Generally, this
      corresponds to sending messages with source network or link-layer
      information that is assigned to or currently properly claimed by
      some other devices in the network.

   TCP:  The Transmission Control Protocol, used on end systems to
      manage data exchange.

   uRPF:  Unicast Reverse Path Forwarding.  A procedure in which the
      route table, which is usually used to look up destination
      addresses and route towards them, is used to look up the source
      address and ensure that one is routing away from it.  When this
      test fails, the event may be logged, and the traffic is commonly
      dropped.




RFC 6959                    SAVI Threat Scope                   May 2013


3.  Spoof-Based Attack Vectors

   Spoofing is employed on the Internet for a number of reasons, most of
   which are in some manner associated with malicious or otherwise
   nefarious activities.  In general, two classes of spoof-based attack
   vectors exist: blind attacks and non-blind attacks.  The following
   sections provide some information on blind and non-blind attacks;
   these sections also include information on attacks where the spoofing
   is primarily intended to interfere with tracing the attacks, as well
   as attacks where spoofing the source address is a necessary component
   to the damage or interference.

3.1.  Blind Attacks

   Blind attacks typically occur when an attacker isn't on the same
   local area network as a source or target, or when an attacker has no
   access to the data path between the attack source(s) and the target
   systems.  In this situation, the attacker has no access to the source
   and target systems.

3.1.1.  Single-Packet Attacks

   One type of blind attacks, which we'll refer to here as "single-
   packet DoS (Denial of Service) attacks", involves an attacking system
   injecting spoofed information into the network, which either results
   in a complete crash of the target system, or in some manner poisons
   some network configuration or other information on a target system so
   as to impact network or other services.

   An example of an attack that can cause a receiving system to crash is
   what is called a LAND (Local Area Network Denial) attack.  A LAND
   attack would consist of an attacking system sending a packet (e.g.,
   TCP SYN) to a target system that contains both a source and
   destination address of that target system.  The packet would also
   contain a single value for the port number, used as both the source
   and destination port number.  Certain target systems will then "lock
   up" when creating connection state associated with the packet or
   would get stuck in a state where a target system continuously replies
   to itself.  As this is an attack that relies on bugs in the target,
   it is possible, but by no means certain, that this threat is no
   longer viable.

   Another form of blind attack is a RST (reset) probe ([RFC4953],
   Section 2.3).  The attacker sends a series of packets to a
   destination that is engaged in a long-lived TCP session.  The packets
   are RST packets, and the attacker uses the known source and
   destination addresses and port numbers, along with guesses at the
   sequence number.  If he can send a packet close enough to the right



RFC 6959                    SAVI Threat Scope                   May 2013


   value, in theory he can terminate the TCP connection.  While there
   are various steps that have been developed to ameliorate this attack,
   preventing the spoofing of source addresses completely prevents the
   attack from occurring.

3.1.2.  Flood-Based DoS

   Flood-based DoS attack vectors are particularly effective attacks on
   the Internet today.  They usually entail flooding a large number of
   packets towards a target system, with the hopes of either exhausting
   connection state on the target system, consuming all packet
   processing capabilities of the target or intermediate systems, or
   consuming a great deal of bandwidth available to the target system
   such that they are essentially inaccessible.

   Because these attacks require no reply from the target system and
   require no legitimate transaction state, attackers often attempt to
   obfuscate the identity of the systems that are generating the attack
   traffic by spoofing the source IP address of the attacking traffic
   flows.  Because ingress filtering isn't applied ubiquitously on the
   Internet today, spoof-based flooding attack vectors are typically
   very difficult to trace back.  In particular, there may be one or
   more attacking sources beyond a network's border, and the attacking
   sources may or may not be legitimate sources; it's difficult to
   determine if the sources are not directly connected to the local
   routing system.  These attacks might be seen as primarily needing to
   be addressed by BCP 38 deployment, which is not in scope for this
   document.  However, as noted earlier, deployment of SAVI can help
   remediate lack of BCP 38 deployment, and even when BCP 38 is
   deployed, SAVI can help provide useful information for responding to
   such attacks.

   Common flood-based DoS attack vectors today include SYN floods, ICMP
   floods, and IP fragmentation attacks.  Attackers may use a single
   legitimate or spoofed fixed attacking source address, although
   frequently they cycle through large swaths of address space.  As a
   result, mitigating these attacks on the receiving end with source-
   based policies is extremely difficult.

   If an attacker can inject messages for a protocol that requires
   control-plane activity, it may be possible to deny network control
   services at a much lower attack level.  While there are various forms
   of protection deployed against this, they are by no means complete.
   Attacks that are harder to trace (such as with spoofed addresses) are
   of course of more concern.






RFC 6959                    SAVI Threat Scope                   May 2013


   Furthermore, the motivator for spoof-based DoS attacks may actually
   be to encourage the target to filter explicitly on a given set of
   source addresses, in order to disrupt access to the target system by
   legitimate owner(s).

3.1.3.  Poisoning Attacks

   While poisoning attacks can often be done with single packets, it is
   also true that a stream of packets can be used to find a window where
   the target will accept the incorrect information.  In general, this
   can be used to perform broadly the same kinds of poisonings as above,
   with more versatility.

   One important class of poisoning attacks are attacks aimed at
   poisoning network or DNS cache information, perhaps to simply break a
   given host's connection or to enable MITM (Man in the Middle) or
   other attacks.  Network-level attacks that could involve single-
   packet DoS include Address Resolution Protocol (ARP) cache poisoning
   and ICMP redirects.  The most obvious example, which depends upon
   falsifying an IP source address, is an on-link attacker poisoning a
   router's ARP or Neighbor Discovery (ND) cache.  The ability to forge
   a source address can also be helpful in causing a DNS cache to accept
   and use incorrect information.

3.1.4.  Spoof-Based Worm/Malware Propagation

   Self-propagating malware has been observed that spoofs its source
   address when attempting to propagate to other systems.  Presumably,
   this was done to obfuscate the actual source address of the infected
   system.  This attack is important both in terms of an attack vector
   that SAVI may help prevent and as a problem that SAVI can help solve
   by tracing back to find infected systems.

3.1.5.  Reflective Attacks

   Reflective amplification attacks -- wherein a sender sends a single
   packet to an intermediary, resulting in the intermediary sending a
   large number of packets, or much larger packets, to the target -- are
   a particularly potent DoS attack vector on the Internet today.  Many
   of these attacks rely on using a false source address, so that the
   amplifier attacks the target by responding to the messages.

   DNS is one of the common targets of such attacks.  The amplification
   factor observed for attacks targeting DNS root and other top-level
   domain name infrastructures in early 2006 was on the order of 72:1
   [VRSN-REPORT].  The result was that just 27 attacking sources with
   512 kbps of upstream attack bandwidth could generate 1 Gbps of
   response attack traffic towards a target system.



RFC 6959                    SAVI Threat Scope                   May 2013


   Smurf attacks employ a similar reflective amplification attack
   vector, exploiting traditional default IP-subnet-directed broadcast
   address behaviors that would result in all the active hosts on a
   given subnet responding to a (spoofed) ICMP echo request from an
   attacker and generating a large amount of ICMP echo response traffic
   directed towards a target system.  These attacks have been
   particularly effective in large campus LAN environments where 50K or
   more hosts might reside on a single subnet.

3.1.6.  Accounting Subversion

   If an attacker wishes to distribute content or other material in a
   manner that employs protocols that require only unidirectional
   flooding and generate no end-to-end transactional state, they may
   desire to spoof the source IP address of that content in order to
   avoid detection or accounting functions enabled at the IP layer.
   While this particular attack has not been observed, it is included
   here to reflect the range of power that spoofed addresses may have,
   even without the ability to receive responses.

3.1.7.  Other Blind Spoofing Attacks

   Other blind spoofing attacks might include spoofing in order to
   exploit source routing or other policy-based routing implemented in a
   network.  It may also be possible in some environments to use
   spoofing techniques to perform blind or non-blind attacks on the
   routers in a site or in the Internet.  There are many techniques to
   mitigate these attacks, but it is well known that there are
   vulnerabilities in this area.

3.2.  Non-blind Attacks

   Non-blind attacks often involve mechanisms such as eavesdropping on
   connections, resetting state so that new connections may be hijacked,
   and an array of other attack vectors.  Perhaps the most common of
   these attack vectors are known as man-in-the-middle attacks.  In this
   case, we are concerned not with an attacker who can modify a stream,
   but rather with one who has access to information from the stream and
   uses that information to launch his own attacks.

3.2.1.  Man in the Middle (MITM)

   Connection hijacking is one of the more common man-in-the-middle
   attack vectors.  In order to hijack a connection, an attacker usually
   needs to be in the forwarding path and oftentimes employs TCP RST or
   other attacks in order to reset a transaction.  The attacker may have
   already compromised a system that's in the forwarding path, or they
   may wish to insert themselves in the forwarding path.



RFC 6959                    SAVI Threat Scope                   May 2013


   For example, an attacker with access to a host on a LAN segment may
   wish to redirect all the traffic on the local segment destined for a
   default gateway address (or all addresses) to itself in order to
   perform man-in-the-middle attacks.  In order to accomplish this in
   IPv4, the attacker might transmit gratuitous ARP [RFC0826] messages
   or ARP replies to the Ethernet broadcast address ff:ff:ff:ff:ff:ff,
   notifying all the hosts on the segment that the IP address(es) of the
   target(s) now maps to its own Layer 2 address.  The source IP address
   in this case is spoofed.  Similar vulnerabilities exist in the IPv6
   ND protocol [RFC4861], although the multicast requirements of the
   IPv6 ND protocol make this harder to perform with the same
   generality.

3.2.2.  Third-Party Recon

   Another example of a non-blind attack is third-party reconnaissance.
   The use of spoofed addresses, while not necessary for this, can often
   provide additional information and helps mask the traceability of the
   activity.  The attack involves sending packets towards a given target
   system and observing either target or intermediate system responses.
   For example, if an attacker were to source spoof TCP SYN packets
   towards a target system from a large set of source addresses and
   observe responses from that target system or some intermediate
   firewall or other middlebox, they would be able to identify what
   IP-layer filtering policies may be in place to protect that system.

3.2.3.  Other Non-blind Spoofing Attacks

   There are presumably many other attacks that can be performed based
   on the ability to spoof source addresses while seeing the target.
   Among other attacks, if there are multiple routers on-link with
   hosts, a host may be able to cause problems for the routing system by
   replaying modified or unmodified routing packets as if they came from
   another router.

















RFC 6959                    SAVI Threat Scope                   May 2013


4.  Current Anti-spoofing Solutions

   The goal of this work is to reduce datagrams with spoofed IP
   addresses from the Internet.  This can be aided by identifying and
   dropping datagrams whose source address binding is incompatible with
   the Internet topology and learned information.  This can be done at
   sites where the relationship between the source address and topology
   and binding information can be checked.  For example, with these
   bindings, in many networks Internet devices can confirm that:

   o  The IP source address is appropriate for the lower-layer address
      (they both identify the same system).

   o  The IP source address is explicitly identified as appropriate for
      the physical topology; for example, the source address is
      appropriate for the Layer 2 switch port through which the datagram
      was received.

   o  The prefix to which the IP source address belongs is appropriate
      for the part of the network topology from which the IP datagram
      was received (while the individual system may be unknown, it is
      reasonable to believe that the system is located in that part of
      the network).

   In general, this involves two kinds of inspection.  The primary
   action is checking the source IP address in the IP header of IP
   packets.  In order to support such checking, the claimed or assigned
   IP addresses in messages concerned with such claims or assignments
   (IP ARP Requests and Responses, DHCP Replies, IPv6 ND Duplicate
   Address Detection (DAD) messages, etc.)  must also be examined and,
   where appropriate, verified.  SAVI is not concerned with verifying IP
   addresses in the contents of arbitrary higher-level protocol
   messages.

   Filtering points farther away from the source of the datagram can
   make decreasingly authoritative assertions about the validity of the
   source address in the datagram.  Nonetheless, there is value in
   dropping traffic that is clearly inappropriate and in maintaining
   knowledge of the level of trust one can place in an address.












RFC 6959                    SAVI Threat Scope                   May 2013


             Edge Network 1            CPE-ISP _.------------.
           _.----------------.         Ingress/   ISP A       `--.
      ,--''                   `---.      ,'                       `.
    ,'  +----+  +------+  +------+ `.   /  +------+       +------+  \\
   (    |Host+--+Switch+--+ CPE  +---)-(---+  PE  +- - - -+ NNI  |   )
    `.  +----+  +------+  |Router| ,'   \\ |Router|       |Router|  /
      `---. Host-neighbor +------+'      `.+------+       +--+---+,'
           `----------------''             '--.              |_.-'
                                               `------------'|
                                                             |
             Edge Network 2                  ISP-ISP Ingress |
           _.----------------.                  _.----------.|
      ,--''                   `---.         ,-''             |--.
    ,'  +----+  +------+  +------+ `.     ,+------+       +--+---+.
   (    |Host+--+Switch+--+ CPE  +---)---+-+  PE  +- - - -+ NNI  | \\
    `.  +----+  +------+  |Router| ,'   (  |Router|       |Router|  )
      `---.               +------+'      \\+------+       +------+ /
           `----------------''            `.                     ,'
                                            '--.   ISP B     _.-'
                                                `----------''

            Figure 1: Points Where an Address Can Be Validated

   Figure 1 illustrates five related paths where a source address can be
   validated:

   o  Host to switch, including host to host via the switch

   o  Host to enterprise CPE router

   o  Enterprise CPE router to ISP edge PE router, and the reverse

   o  ISP NNI router to ISP NNI router

   In general, datagrams with spoofed IP addresses can be detected and
   discarded by devices that have an authoritative mapping between IP
   addresses and the network topology.  For example, a device that has
   an authoritative table between link-layer and IP addresses on a link
   can discard any datagrams in which the IP address is not associated
   with the link-layer address in the datagram.  The degree of
   confidence in the source address depends on where the spoofing
   detection is performed, as well as the prefix aggregation in place
   between the spoofing detection and the source of the datagram.








RFC 6959                    SAVI Threat Scope                   May 2013


4.1.  Topological Locations for Enforcement

   There are a number of kinds of places, which one might call
   topological locations, where solutions may or should be deployed.  As
   can be seen in the details below, as the point of enforcement moves
   away from a single cable attached directly to the host being
   validated, additional complications arise.  It is likely that fully
   addressing many of these cases may require additional coordination
   mechanisms across the device that covers the disparate paths.

4.1.1.  Host to Link-Layer Neighbor via Switch

   The first point at which a datagram with a spoofed address can be
   detected is on the link to which the source of the datagram is
   connected.  At this point in the network, the source link-layer and
   IP addresses are both available and can be validated against each
   other, and potentially against the physical port being used.  A
   datagram in which the IP source address does not match the
   corresponding link-layer address can be discarded.  Of course, the
   trust in the filtering depends on the trust in the method through
   which the mappings are developed.  This mechanism can be applied by a
   first-hop router, or switch on the link.  The first-hop switch has
   the most precise information for this.

   On a truly shared medium link, such as classic Ethernet, the best
   that can be done is to validate the link-layer and IP addresses
   against the mappings.  When the link is not shared, such as when the
   hosts are connected through a switch, the source host can be
   identified precisely based on the port through which the datagram is
   received or the Layer 2 address if it is known to the switch.  Port
   identification prevents transmission of malicious datagrams whose
   link-layer and IP addresses are both spoofed to mimic another host.

   Other kinds of links may fall at different places in this spectrum,
   with some wireless links having easier ways of identifying individual
   devices than others, for example.

4.1.2.  Upstream Switches

   In many topologies, there can be additional switches between the
   host-attached switch and the first router in the network.  In these
   cases, additional issues can arise that affect SAVI operations.  If
   the bridging topologies that connect the switches change, or if the
   Link Aggregation Control Protocol (LACP) [IEEE802.1AX], the Virtual
   Router Redundancy Protocol (VRRP), or link management operations
   change the links that are used to deliver traffic, the switch may
   need to move the SAVI state to a different port, or the state may
   need to be moved or reestablished on a different switch.



RFC 6959                    SAVI Threat Scope                   May 2013


4.1.3.  Upstream Routers

   Beyond the first-hop router, subsequent routers may additionally
   filter traffic from downstream networks.  Because these routers do
   not have access to the link-layer address of the device from which
   the datagram was sent, they are limited to confirming that the source
   IP address is within a prefix that is appropriate for a downstream
   router from which the datagram was received.

   Options include the use of simple access lists or the use of Unicast
   Reverse Path Forwarding (uRPF).  Access lists are generally
   appropriate only for the simplest cases, as management can be
   difficult.  Strict uRPF accepts the source address on a datagram if
   and only if it comes from a direction that would be rational to send
   a datagram directed to the address, which means that the filter is
   derived from routing information.  These filtering procedures are
   discussed in more detail in [RFC3704].

   In many cases, this router has access to information about what IP
   prefixes are to be used on a given subnet.  This might be because it
   delegated that prefix through DHCP or monitored such a delegation.
   It may have advertised that prefix in IPv6 Neighbor Discovery Router
   Advertisement messages, or monitored such an advertisement.  These
   can be seen as generalizations of the access lists above.  When the
   topology permits, the router can enforce that these prefixes are used
   by the hosts.

4.1.4.  ISP Edge PE Router

   An obvious special case of the discussion is with an ISP PE router,
   where it provides its customer with access.  BCP 38 specifically
   encourages ISPs to use ingress filtering to limit the incidence of
   spoofed addresses in the network.

   The question that the ISP must answer for itself is the degree to
   which it trusts its downstream network.  A contract might be written
   between an ISP and its customer requiring that the customer apply the
   procedures of network ingress filtering to the customer's own
   network, although there's no way upstream networks would be able to
   validate this.

   Conversely, if the provider has assigned a single IP address to the
   customer (for example, with IPv4 NAT in the CPE), PE enforcement of
   BCP 38 can be on the full address, simplifying many issues.







RFC 6959                    SAVI Threat Scope                   May 2013


4.1.5.  ISP NNI Router to ISP NNI Router

   The considerations explicitly related to customer networks can also
   be applied to neighboring ISPs.  An interconnection agreement might
   be written between two companies requiring that network ingress
   filtering policy be implemented on all customer connections.  ISPs
   might, for example, mark datagrams from neighboring ISPs that do not
   sign such a contract or demonstrably do not behave in accordance with
   it as 'untrusted'.  Alternatively, the ISP might place untrusted
   prefixes into a separate BGP community [RFC4271] and use that to
   advertise the level of trust to its BGP peers.

   In this case, uRPF is less effective as a validation tool, due to
   asymmetric routing.  However, when it can be shown that spoofed
   addresses are present, the procedure can be applied.

   Part of the complication here is that in the abstract, it is very
   difficult to know what addresses should appear in packets sent from
   one ISP to another.  Hence, packet-level filtering and enforcement
   are very difficult at this point in the network.  Whether one views
   this as specific to the NNI, or a general property of the Internet,
   it is still a major factor that needs to be taken into account.

4.1.6.  Cable Modem Subscriber Access

   Cable Modem Termination Systems (CMTS) employ Data Over Cable Service
   Interface Specification (DOCSIS) Media Access Control (MAC) domains.
   These share some properties with general switched networks, as
   described above in Section 4.1.1, and some properties with DSL access
   networks, as described below in Section 4.1.7.  They also often have
   their own provisioning and monitoring tools that may address some of
   the issues described here.

4.1.7.  DSL Subscriber Access

   While DSL subscriber access can be bridged or routed, as seen by the
   service provider's device, it is generally the case that the
   protocols carry enough information to validate which subscriber is
   sending packets.  Thus, for ensuring that one DSL subscriber does not
   spoof another, enforcement can generally be done at the aggregation
   router.  This is true even when there is a bridged infrastructure
   among the subscribers, as DSL access generally requires all
   subscriber traffic to go through the access aggregation router.








RFC 6959                    SAVI Threat Scope                   May 2013


   If it is desirable to provide spoofing protection among the devices
   within a residence, that would need to be provided by the CPE device,
   as the ISP's router does not have enough visibility to do that.  It
   is not clear at this time that this problem is seen as a relevant
   threat.

4.2.  Currently Available Tools

   There are a number of tools that have been developed, and have seen
   some deployment, for addressing these attacks.

4.2.1.  BCP 38

   If BCP 38 [RFC2827] is implemented in LAN segments, it is typically
   done so on subnetwork boundaries and traditionally relates only to
   network-layer ingress filtering policies.  The result is that hosts
   within the segment cannot spoof packets from address space outside of
   the local segment itself; however, they may still spoof packets using
   sources' addresses that exist within the local network segment.

4.2.2.  Unicast RPF

   Unicast RPF is a crude mechanism to automate definition of BCP 38
   style filters based on routing table information.  Its applicability
   parallels that of BCP 38, although deployment caveats exist, as
   outlined in [RFC3704].

4.2.3.  Port-Based Address Binding

   Much of the work of SAVI is initially targeted at minimizing source
   address spoofing in the LAN.  In particular, if mechanisms can be
   defined to accommodate configuration of port binding information for
   IP, either to a port, to an unchangeable or authenticated MAC
   address, or to other credentials in the packet such that an impostor
   cannot create the needed values, a large portion of the spoofing
   threat space in the LAN can be marginalized.

   However, establishing this binding is not trivial and varies across
   both topology types and address allocation mechanisms.

4.2.3.1.  Manual Binding

   Binding of a single link-layer and network-layer address to a port
   may initially seem trivial.  However, two primary areas exist that
   can complicate such techniques.  In particular, these areas involve
   topologies where more than a single IP-layer address may be
   associated with a MAC address on a given port, or where multiple
   hosts are connected via a single physical port.  Furthermore, if one



RFC 6959                    SAVI Threat Scope                   May 2013


   or more dynamic address allocation mechanisms such as DHCP are
   employed, then some mechanism must exist to associate those IP-layer
   addresses with the appropriate link-layer ports as addresses are
   allocated or reclaimed.

4.2.3.2.  Automated Binding

   For IPv4, the primary and very widely used automated address
   assignment technique is DHCP-based address assignment.  This can be
   coupled with filtering policies that control which hosts can
   originate DHCP replies.  Under such circumstances, SAVI switches can
   treat DHCP replies as authoritative sources of IP address binding
   information.  By eavesdropping on the DHCP exchanges, the SAVI switch
   can create the bindings needed for address usage enforcement.

   For IPv6, there are two common automated address assignment
   techniques.  While there are many variations and details, for
   purposes of understanding the threats and basic responses, these are
   Stateless Address Autoconfiguration (SLAAC) and DHCP-based IPv6
   address assignment.  For DHCP-based IPv6 address assignment, the
   techniques above are applicable and suitable.

   When SLAAC is used for IPv6 address assignment, the switches can
   observe the duplicate address detection messages and use those to
   create the enforcement bindings.  This enables the switches to ensure
   that only properly claimed IP addresses are used for data traffic.
   It does not enforce that these addresses are assigned to the hosts,
   since SLAAC does not have a notion of address assignment.

4.2.3.3.  IEEE 802.1x

   IEEE 802.1x is an authentication protocol that permits a network to
   determine the identity of a user seeking to join it and apply
   authorization rules to permit or deny the action.  In and of
   themselves, such tools confirm only that the user is authorized to
   use the network, but they do not enforce what IP address the user is
   allowed to use.  It is worth noting that elements of 802.1x may well
   be useful as binding anchors for SAVI solutions.

4.2.4.  Cryptographic Techniques

   MITM and replay attacks can typically be mitigated with cryptographic
   techniques.  However, many of the applications today either don't or
   can't employ cryptographic authentication and protection mechanisms.
   ARP for IPv4 does not use such protection.  While Secure Neighbor
   Discovery (SEND) provides such protection for the IPv6 ND protocol,
   SEND is not widely used to date.  Usage of such techniques is outside
   the scope of this document.



RFC 6959                    SAVI Threat Scope                   May 2013


   While DNSSEC will significantly help protect DNS from the effects of
   spoof-based poisoning attacks, such protection does not help protect
   the rest of the network from spoofed attacks.

4.2.5.  Residual Attacks

   It should be understood that not all combinations of network,
   service, and enforcement choices will result in a protectable
   network.  For example, if one uses conventional SLAAC in a switched
   network, but tries to only provide address enforcement on the routers
   on the network, then the ability to provide protection is severely
   limited.

5.  Topological Challenges Facing SAVI

   As noted previously, topological components and address allocation
   mechanisms have significant implications on what is feasible with
   regard to link-layer address and IP address port bindings.  The
   following sections discuss some of the various topologies and address
   allocation mechanisms that proposed SAVI solutions should attempt to
   address.

5.1.  Address Provisioning Mechanisms

   In a strictly static environment, configuration management for access
   filters that map link-layer and network-layer addresses on a specific
   switch port might be a viable option.  However, most networks,
   certainly those that accommodate actual human users, are much more
   dynamic in nature.  As such, mechanisms that provide port-MAC-IP
   bindings need to accommodate dynamic address allocation schemes
   enabled by protocols such as DHCP, DHCPv6 for address allocation, and
   IPv6 Stateless Address Autoconfiguration.

5.2.  LAN Devices with Multiple Addresses

   From the perspective of network topology, consider hosts connected to
   switch ports that may have one or more IP addresses, and devices that
   forward packets from other network segments.  It is much harder to
   enforce port-MAC-IP bindings on traffic from such hosts and devices
   than for traffic from more simply connected devices.

5.2.1.  Routers

   Routers are the most obvious examples of devices for which it is
   problematic to implement port-MAC-IP bindings.  Routers not only
   originate packets themselves and often have multiple interfaces, but
   also forward packets from other network segments.  As a result, it's




RFC 6959                    SAVI Threat Scope                   May 2013


   difficult for port-MAC-IP binding rules to be established a priori,
   because it's likely that many addresses and IP subnets should be
   associated with the port-MAC in question.

5.2.2.  NATs

   Validating traffic from prefix-based and multi-address NATs is also
   problematic, for the same reasons as for routers.  Because they may
   forward traffic from an array of addresses, validation requires
   advance knowledge of the IPs that should be associated with a given
   port-MAC pair.

5.2.3.  Multi-instance Hosts

   Another example that introduces complexities is that of multi-
   instance hosts attached to a switch port.  These are single physical
   devices that internally run multiple physical or logical hosts.  When
   the device is a blade server, e.g., with internal blades each hosting
   a physical machine, there is essentially a physical switch inside the
   blade server.  While feasible, this creates some complexity for
   determining where enforcement logic can or should live.

   Logically distinct hosts, such as are provided by many varieties of
   virtualization logic, result in a single physical host and connect to
   a single port on the Ethernet switch in the topology, actually having
   multiple internal virtual machines.  Each virtual machine may have
   its own IP and MAC addresses.  These are connected by what is
   essentially (or sometimes literally) an internal LAN switch.  While
   this internal switch may be a SAVI enforcement point to help control
   threats among the virtual hosts, or between virtual hosts and other
   parts of the network, such enforcement cannot be counted on in all
   implementations.  If the virtual machines are interconnected by the
   internal switch, then that logical device is the first switch for the
   purposes of this analysis.

   A further complication with multi-instance hosts is that in many
   environments, these hosts may move while retaining their IP
   addresses.  This can be an actual relocation of the running software,
   or a backup instance taking over the functions of the software.  In
   both cases, the IP address will appear at a new topological location.
   Depending upon the protocols used, it may have the same MAC address
   or a different one, and the system may or may not issue a gratuitous
   ARP request after relocation.  When such a move is done without
   changing the MAC address, the SAVI switches will need to update their
   state.  While ARP may be helpful, traffic detection, switch-based
   neighbor solicitation, interaction with an orchestration system, or
   other means may be used.




RFC 6959                    SAVI Threat Scope                   May 2013


5.2.4.  Multi-LAN Hosts

   Multi-interface hosts, in particular those that are multihomed and
   may forward packets from any of a number of source addresses, can be
   problematic as well.  In particular, if a port-MAC-IP binding is made
   on each of the interfaces, and then either a loopback IP or the
   address of a third interface is used as the source address of a
   packet forwarded through an interface for which the port-MAC-IP
   binding doesn't map, the traffic may be discarded.  Static
   configuration of port-MAC-IP bindings may accommodate this scenario,
   although some a priori knowledge of address assignment and topology
   is required.

   While it is rare to use loopback addressing or to send packets out of
   one interface with the source address of another, these rarities do
   legitimately occur.  Some servers, particularly ones that have
   underlying virtualization, use loopback techniques for management.

5.2.5.  Firewalls

   Firewalls that forward packets from other network segments, or serve
   as a source for locally originated packets, suffer from the same
   issues as routers.

5.2.6.  Mobile IP

   Mobile IP hosts in both IPv4 and IPv6 are proper members of the site
   where they are currently located.  Their care-of address is a
   properly assigned address that is on the link they are using, and
   their packets are sent and received using that address.  Thus, they
   do not introduce any additional complications.  (There was at one
   time consideration of allowing mobile hosts to use their home address
   when away from home.  This was not done, precisely to ensure that
   mobile hosts comply with source address validity requirements.)
   Mobile hosts with multiple physical interfaces fall into the cases
   above.

   Mobile IP Home Agents (HAs) are somewhat more interesting.  Although
   they are (typically) fixed devices, they are required to send and
   receive packets addressed from or to any currently properly
   registered mobile node.  From an analysis point of view, even though
   the packets that an HA handles are actually addressed to or from the
   link the HA is on, it is probably best to think of them as routers,
   with a virtual interface to the actual hosts they are serving.  Thus,
   if the Mobile IP HA is trusted, it can itself perform IP source
   address checking on the packets it forwards on behalf of mobile
   nodes.  This would utilize bindings established by the Mobile IP
   registration mechanisms.



RFC 6959                    SAVI Threat Scope                   May 2013


5.2.7.  Other Topologies

   Any topology that results in the possibility that a device connected
   to a switch port may forward packets with more than a single source
   address for a packet that it originated may be problematic.
   Additionally, address allocation schemas introduce additional
   considerations when examining a given SAVI solutions space.

5.3.  IPv6 Considerations

   IPv6 introduces additional capabilities that indirectly complicate
   the spoofing analysis.  IPv6 introduces and recommends the use of
   SLAAC [RFC4862].  This allows hosts to determine their IP prefix,
   select an Interface Identifier (IID), and then start communicating.
   While there are many advantages to this, the absence of control
   interactions complicates the process of behavioral enforcement.

   An additional complication is the very large IID space.  Again, this
   64-bit IID space provided by IPv6 has many advantages.  It provides
   the opportunity for many useful behaviors.  However, it also means
   that in the absence of controls, hosts can mint anonymous addresses
   as often as they like, modulo the idiosyncrasies of the duplicate
   address procedure.  Like many behaviors, this is a feature for some
   purposes and a problem for others.  For example, without claiming the
   entire IID space, an on-link attacker may be able to generate enough
   IP addresses to fill the Neighbor Discovery table space of the other
   Layer 3 (L3) devices on the link, including switches that are
   monitoring L3 behavior.  This could seriously interfere with the
   ability of other devices on the link to function.

6.  Analysis of Host Granularity Anti-spoofing

   Applying anti-spoofing techniques at the host level enables a site to
   achieve several valuable objectives.  While it is likely the case
   that for many site topologies and policies full source spoofing
   protection is not possible, it is also true that for many sites there
   are steps that can be taken that provide benefit.

   One important class of benefit is masquerade prevention.  Security
   threats involving one machine masquerading as another, for example,
   in order to hijack an apparently secure session, can occur within a
   site with significant impact.  Having mechanisms such that host-
   facing devices prevent this is a significant intra-site security
   improvement.  Given that security experts report that most security
   breaches are internal, this can be valuable.  One example of this is
   that such techniques should mitigate internal attacks on the site
   routing system.




RFC 6959                    SAVI Threat Scope                   May 2013


   A second class of benefit is related to the traceability described
   above.  When a security incident is detected, either within a site or
   externally (and traced to the site), it can be critical to determine
   the actual source of the incident.  If address usage can be tied to
   the kinds of anchors described earlier, this can help in responding
   to security incidents.

   In addition to these local observable benefits, there can be more
   global benefits.  For example, if address usage is tied to anchors,
   it may be possible to prevent or control the use of large numbers of
   anonymous IPv6 addresses for attacks, or at least to trace even those
   attacks back to their source.

   As described below in the security considerations, these operational
   behaviors need to be evaluated in the context of the reduction in
   user privacy implied if one logs traffic bindings.  In particular, in
   addition to the architectural trade-offs, the network administrator
   must plan for the proper handling of this relevant privacy
   information about his users.

7.  Security Considerations

   This document provides limited discussion of some security threats
   that source address validation improvements will help to mitigate.
   It is not meant to be all-inclusive, either from a threat analysis
   perspective or from the source address validation application side.

   It is seductive to think of SAVI solutions as providing the ability
   to use this technology to trace a datagram to the person, or at least
   end system, that originated it.  For several reasons, the technology
   can be used to derive circumstantial evidence, but does not actually
   solve that problem.

   In the Internet layer, the source address of a datagram should be the
   address of the system that originated it and to which any reply is
   expected to come.  But systems fall into several broad categories.
   Many are single-user systems, such as laptops and PDAs.  Multi-user
   systems are commonly used in industry, and a wide variety of
   middleware systems and application servers have no users at all, but
   by design relay messages or perform services on behalf of users of
   other systems (e.g., SMTP and peer-to-peer file sharing).

   Even if every Internet-connected network implements source address
   validation at the ultimate network ingress, and assurances exist that
   intermediate devices are to never modify datagram source addresses,
   source addresses cannot be used as an authentication mechanism.  The





RFC 6959                    SAVI Threat Scope                   May 2013


   only techniques for unquestionably validating source addresses of
   a received datagram are cryptographic authentication mechanisms
   such as IPsec.

   It must be presumed that there will be some failure modes in any SAVI
   deployment, given the history of technical security mechanisms.  A
   possible attack to be considered by network administrators is an
   inside attack probing the network for modes of spoofing that can be
   accomplished.  If the probes are conducted at a level below alarm
   thresholds, this might allow an internal attacker to safely determine
   what spoof modes he can use.  Thus, the use of these techniques must
   be managed in such a way as to avoid giving a false sense of security
   to the network administrator.

7.1.  Privacy Considerations

   It should be understood that enforcing and recording IP address
   bindings have privacy implications.  In some circumstances, this
   binding data may be considered to be personally identifying
   information.  In general, collecting private information about users
   brings ethical and legal responsibilities to the network
   administrator.

   For this reason, collection and retention of logged binding
   information need to be considered carefully.  Prevention of spoofing
   does not in itself require such retention.  Analysis of immediate
   events may rely on having logs of current bindings.  Thus, privacy
   issues can be ameliorated by removing binding logs after the binding
   lifetimes expire.  Logs of apparent spoof attempts are a separate
   matter and may require longer retention to detect patterns of
   deliberate or accidental abuse.

   With operations of the type described here, the network administrator
   is collecting information about where on his network the user is
   active.  In addition, the recorded bindings supplement address usage
   information about users that is available from DHCP logs.  For
   example, if IPv6 SLAAC is being used, and IP to Layer 2 address
   bindings are being logged, the administrator will have access to
   information associating users with their IP addresses even if IPv6
   privacy addresses are used.

   In addition to this, care must be taken in attributing actions to
   users on the basis of this sort of information.  Whatever the
   theoretical strength of the tools, administrators should always allow
   for such information being wrong and should be careful about any
   actions taken on the basis of apparent attribution.  These techniques
   do nothing about address spoofing from other sites, so any evaluation
   of attribution also needs to allow for such cases.



RFC 6959                    SAVI Threat Scope                   May 2013


8.  Acknowledgments

   A portion of the primer text in this document came directly from
   [SAVA], authored by Fred Baker and Ralph Droms.  Many thanks to
   Christian Vogt, Suresh Bhogavilli, and Pekka Savola for contributing
   text and a careful review of this document.

9.  References

9.1.  Normative References

   [RFC0791]  Postel, J., "Internet Protocol", STD 5, RFC 791,
              September 1981.

   [RFC2460]  Deering, S. and R. Hinden, "Internet Protocol, Version 6
              (IPv6) Specification", RFC 2460, December 1998.

9.2.  Informative References

   [IEEE802.1AX]
              IEEE, "IEEE Standard for Local and metropolitan area
              networks - Link Aggregation", IEEE 802.1AX, 2008.

   [RFC0826]  Plummer, D., "Ethernet Address Resolution Protocol: Or
              converting network protocol addresses to 48.bit Ethernet
              address for transmission on Ethernet hardware", STD 37,
              RFC 826, November 1982.

   [RFC2827]  Ferguson, P. and D. Senie, "Network Ingress Filtering:
              Defeating Denial of Service Attacks which employ IP Source
              Address Spoofing", BCP 38, RFC 2827, May 2000.

   [RFC3704]  Baker, F. and P. Savola, "Ingress Filtering for Multihomed
              Networks", BCP 84, RFC 3704, March 2004.

   [RFC4271]  Rekhter, Y., Li, T., and S. Hares, "A Border Gateway
              Protocol 4 (BGP-4)", RFC 4271, January 2006.

   [RFC4861]  Narten, T., Nordmark, E., Simpson, W., and H. Soliman,
              "Neighbor Discovery for IP version 6 (IPv6)", RFC 4861,
              September 2007.

   [RFC4862]  Thomson, S., Narten, T., and T. Jinmei, "IPv6 Stateless
              Address Autoconfiguration", RFC 4862, September 2007.

   [RFC4953]  Touch, J., "Defending TCP Against Spoofing Attacks",
              RFC 4953, July 2007.




RFC 6959                    SAVI Threat Scope                   May 2013


   [SAVA]     Baker, F. and R. Droms, "IPv4/IPv6 Source Address
              Verification", Work in Progress, June 2007.

   [VRSN-REPORT]
              Silva, K., Scalzo, F., and P. Barber, "Anatomy of Recent
              DNS Reflector Attacks from the Victim and Reflector Point
              of View", VeriSign White Paper, April 2006.

Authors' Addresses

   Danny McPherson
   VeriSign, Inc.

   EMail: dmcpherson@verisign.com


   Fred Baker
   Cisco Systems

   EMail: fred@cisco.com


   Joel M. Halpern
   Ericsson

   EMail: joel.halpern@ericsson.com